diff --git a/edge_deployment/fabric_switch_bootstrap.rst b/edge_deployment/fabric_switch_bootstrap.rst
index d40a878..3dad67a 100644
--- a/edge_deployment/fabric_switch_bootstrap.rst
+++ b/edge_deployment/fabric_switch_bootstrap.rst
@@ -2,20 +2,14 @@
    SPDX-FileCopyrightText: © 2020 Open Networking Foundation <support@opennetworking.org>
    SPDX-License-Identifier: Apache-2.0
 
-Fabric Switch Bootstrap (Beta)
-==============================
-
-.. note::
-
-   Fabric switches running the P4 UPF is a beta feature of the Aether 1.5
-   release, and the hardware and software setup is not required if using the
-   BESS UPF.
+Fabric Switch Bootstrap
+=======================
 
 The installation of the ONL OS image on the fabric switches uses the DHCP and
 HTTP server set up on the management server.
 
 The default image is downloaded during that installation process by the
-``onieboot`` role. Make changes to that roll and rerun the management playbook
+``onieboot`` role. Make changes to that role and rerun the management playbook
 to download a newer switch image.
 
 Preparation
@@ -25,109 +19,12 @@
 ONL. Find out the MAC addresses for both of these ports and enter it into
 NetBox.
 
-Change boot mode to ONIE Rescue mode
-------------------------------------
+Installing Open Network Linux
+-----------------------------
+See :ref:`Provision Switches <sdfabric:deployment:step 1: provision switches>`
+to learn about how to enter ONIE Rescue mode and install Open Network Linux on the switches.
 
-In order to reinstall an ONL image, you must change the ONIE bootloader to
-"Rescue Mode".
-
-Once the switch is powered on, it should retrieve an IP address on the OpenBMC
-interface with DHCP. OpenBMC uses these default credentials::
-
-  username: root
-  password: 0penBmc
-
-Login to OpenBMC with SSH::
-
-  $ ssh root@10.0.0.131
-  The authenticity of host '10.0.0.131 (10.0.0.131)' can't be established.
-  ECDSA key fingerprint is SHA256:...
-  Are you sure you want to continue connecting (yes/no)? yes
-  Warning: Permanently added '10.0.0.131' (ECDSA) to the list of known hosts.
-  root@10.0.0.131's password:
-  root@bmc:~#
-
-Using the Serial-over-LAN Console, enter ONL::
-
-  root@bmc:~# /usr/local/bin/sol.sh
-  You are in SOL session.
-  Use ctrl-x to quit.
-  -----------------------
-
-  root@onl:~#
-
-.. note::
-  If `sol.sh` is unresponsive, please try to restart the mainboard with::
-
-    root@onl:~# wedge_power.sh reset
-
-
-Change the boot mode to rescue mode with the command ``onl-onie-boot-mode
-rescue``, and reboot::
-
-  root@onl:~# onl-onie-boot-mode rescue
-  [1053033.768512] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
-  [1053033.936893] EXT4-fs (sda3): re-mounted. Opts: (null)
-  [1053033.996727] EXT4-fs (sda3): re-mounted. Opts: (null)
-  The system will boot into ONIE rescue mode at the next restart.
-  root@onl:~# reboot
-
-At this point, ONL will go through it's shutdown sequence and ONIE will start.
-If it does not start right away, press the Enter/Return key a few times - it
-may show you a boot selection screen. Pick ``ONIE`` and ``Rescue`` if given a
-choice.
-
-Installing an ONL image over HTTP
----------------------------------
-
-Now that the switch is in Rescue mode
-
-First, activate the Console by pressing Enter::
-
-  discover: Rescue mode detected.  Installer disabled.
-
-  Please press Enter to activate this console.
-  To check the install status inspect /var/log/onie.log.
-  Try this:  tail -f /var/log/onie.log
-
-  ** Rescue Mode Enabled **
-  ONIE:/ #
-
-Then run the ``onie-nos-install`` command, with the URL of the management
-server on the management network segment::
-
-  ONIE:/ # onie-nos-install http://10.0.0.129/onie-installer
-  discover: Rescue mode detected. No discover stopped.
-  ONIE: Unable to find 'Serial Number' TLV in EEPROM data.
-  Info: Fetching http://10.0.0.129/onie-installer ...
-  Connecting to 10.0.0.129 (10.0.0.129:80)
-  installer            100% |*******************************|   322M  0:00:00 ETA
-  ONIE: Executing installer: http://10.0.0.129/onie-installer
-  installer: computing checksum of original archive
-  installer: checksum is OK
-  ...
-
-The installation will now start, and then ONL will boot culminating in::
-
-  Open Network Linux OS ONL-wedge100bf-32qs, 2020-11-04.19:44-64100e9
-
-  localhost login:
-
-The default ONL login is::
-
-  username: root
-  password: onl
-
-If you login, you can verify that the switch is getting it's IP address via
-DHCP::
-
-  root@localhost:~# ip addr
-  ...
-  3: ma1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
-      link/ether 00:90:fb:5c:e1:97 brd ff:ff:ff:ff:ff:ff
-      inet 10.0.0.130/25 brd 10.0.0.255 scope global ma1
-  ...
-
+Please return here and continue the rest of the step once you finish ONL installation.
 
 Post-ONL Configuration
 ----------------------