diff --git a/scripts/cloudlab-disksetup.sh b/scripts/cloudlab-disksetup.sh
new file mode 100755
index 0000000..1e2765f
--- /dev/null
+++ b/scripts/cloudlab-disksetup.sh
@@ -0,0 +1,68 @@
+#!/usr/bin/env bash
+
+# Copyright 2017-present Open Networking Foundation
+#
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+###############################################
+# Disk setup and symlinks for a CloudLab node #
+###############################################
+
+# Don't do anything if not a CloudLab node
+[ ! -d /usr/local/etc/emulab ] && return
+
+# Mount extra space, if haven't already
+if [ ! -d /mnt/extra ]
+then
+    sudo mkdir -p /mnt/extra
+
+    # for NVME SSD on Utah m510, not supported by mkextrafs
+    if df | grep -q nvme0n1p1 && [ -e /usr/testbed/bin/mkextrafs ]
+    then
+        # set partition type of 4th partition to Linux, ignore errors
+        echo -e "t\\n4\\n82\\np\\nw\\nq" | sudo fdisk /dev/nvme0n1 || true
+
+        sudo mkfs.ext4 /dev/nvme0n1p4
+        echo "/dev/nvme0n1p4 /mnt/extra/ ext4 defaults 0 0" | sudo tee -a /etc/fstab
+        sudo mount /mnt/extra
+        mount | grep nvme0n1p4 || (echo "ERROR: NVME mkfs/mount failed, exiting!" && exit 1)
+
+    elif [ -e /usr/testbed/bin/mkextrafs ] && [ -b /dev/sdb ] # if on Clemson/Wisconsin Cloudlab
+    then
+        # Sometimes this command fails on the first try
+        sudo /usr/testbed/bin/mkextrafs -s 1 -r /dev/sdb -qf "/mnt/extra/" || sudo /usr/testbed/bin/mkextrafs -s 1 -r /dev/sdb -qf "/mnt/extra/"
+
+        # Check that the mount succeeded (sometimes mkextrafs succeeds but device not mounted)
+        mount | grep sdb || (echo "ERROR: mkextrafs failed, exiting!" && exit 1)
+
+    elif [ -e /usr/testbed/bin/mkextrafs ] && [ -b /dev/sda4 ] # if on Utah xl170
+    then
+        # set partition type of 4th partition to Linux, ignore errors
+        printf "t\\n4\\n83\\np\\nw\\nq" | sudo fdisk /dev/sda || true
+
+        sudo mkfs.ext4 /dev/sda4
+        echo "/dev/sda4 /mnt/extra/ ext4 defaults 0 0" | sudo tee -a /etc/fstab
+        sudo mount /mnt/extra
+        mount | grep sda4 || (echo "ERROR: mkfs/mount failed, exiting!" && exit 1)
+    fi
+fi
+
+for DIR in docker kubelet openstack-helm nova
+do
+    sudo mkdir -p "/mnt/extra/$DIR"
+    sudo chmod -R a+rwx "/mnt/extra/$DIR"
+    if [ ! -e "/var/lib/$DIR" ]
+    then
+        sudo ln -s "/mnt/extra/$DIR" "/var/lib/$DIR"
+    fi
+done
diff --git a/scripts/omec-nodesetup.sh b/scripts/omec-nodesetup.sh
new file mode 100755
index 0000000..e84bbb4
--- /dev/null
+++ b/scripts/omec-nodesetup.sh
@@ -0,0 +1,168 @@
+#!/bin/bash
+
+# Copyright 2019-present Open Networking Foundation
+#
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+SRIOV_PF=${1:?"Specify SR-IOV interface name as argv[1]"}
+NR_HUGEPAGE=32
+
+if [ "$(id -u)" != "0" ]; then
+        echo "FAIL: You should run this as root."
+        echo "HINT: sudo $0 $SRIOV_PF"
+        exit 1
+fi
+
+grub_updated=0
+function update_grub_cmdline {
+        local param=$1
+        IFS='=' read -r key value <<< "$param"
+        if ! grep -q "$key"= /etc/default/grub; then
+                sed -i "s/^GRUB_CMDLINE_LINUX=\"/&${param} /" /etc/default/grub
+        else
+                sed -i "s/\\(${key}=\\)\\w*/\\1${value}/g" /etc/default/grub
+        fi
+        echo "      Added \"${param}\" is to kernel parameters"
+        grub_updated=1
+}
+
+function check_vf {
+        local pfpci
+        local num_vfs
+
+        pfpci=$(readlink /sys/devices/pci*/*/*/net/"$SRIOV_PF"/device | awk '{print substr($1,10)}')
+        num_vfs=$(cat /sys/class/net/"$SRIOV_PF"/device/sriov_numvfs)
+        if [ "$num_vfs" = "0" ]; then
+                echo "FAIL: SR-IOV VFs are not created"
+                return 1
+        fi
+
+        local vfpci
+        local driver
+        for ((idx = 0; idx < num_vfs; idx++)); do
+                local vfn="virtfn$idx"
+                # shellcheck disable=SC2012
+                vfpci=$(ls -l /sys/devices/pci*/*/"$pfpci" | awk -v vfn=$vfn 'vfn==$9 {print substr($11,4)}')
+                driver=$(lspci -vvv -s "$vfpci" | grep "Kernel driver in use" | awk '{print $5}')
+                if [ "$driver" != "vfio-pci" ]; then
+                        echo "FAIL: SR-IOV VF $idx does not exist or bind to vfio-pci"
+                        return 1
+                fi
+        done
+        return 0
+}
+
+# Check hardware virtualization is enabled
+# --------------------------
+virt=$(grep -E -m1 -w '^flags[[:blank:]]*:' /proc/cpuinfo | grep -E -wo '(vmx|svm)') || true
+if [ -z "$virt" ]; then
+        echo "FATAL: Your CPU does not support hardware virtualization."
+        exit 1
+fi
+
+msr="/dev/cpu/0/msr"
+if [ ! -r "$msr" ]; then
+        modprobe msr
+fi
+
+disabled=0
+if [ "$virt" = "vmx" ]; then
+        BIT=$(rdmsr --bitfield 0:0 0x3a 2>/dev/null || true)
+        if [ "$BIT" = "1" ]; then
+                BIT=$(rdmsr --bitfield 2:2 0x3a 2>/dev/null || true)
+                if [ "$BIT" = "0" ]; then
+                        disabled=1
+                fi
+        fi
+elif [ "$virt" = "svm" ]; then
+        BIT=$(rdmsr --bitfield 4:4 0xc0010114 2>/dev/null || true)
+        if [ "$BIT" = "1" ]; then
+                disabled=1
+        fi
+else
+        echo "FATAL: Unknown virtualization extension: $virt."
+        exit 1
+fi
+
+if [ "$disabled" -eq 1 ]; then
+        echo "FAIL: $virt is disabled by BIOS"
+        echo "HINT: Enter your BIOS setup and enable Virtualization Technology (VT),"
+        echo "      and then hard poweroff/poweron your system"
+else
+        echo "  OK: $virt is enabled"
+fi
+
+# Ensure IOMMU is enabled
+# --------------------------
+if ! compgen -G "/sys/class/iommu/*/devices" > /dev/null; then
+        disabled=1
+        echo "FAIL: IOMMU is disabled"
+        update_grub_cmdline "intel_iommu=on"
+else
+        echo "  OK: IOMMU is enabled"
+fi
+
+# Ensure hugepage is enabled
+# --------------------------
+hugepage=$(grep -i HugePages_Total /proc/meminfo | awk '{print $2}') || true
+if [ "$hugepage" -eq "0" ]; then
+        disabled=1
+        echo "FAIL: Hugepage is disabled"
+
+        update_grub_cmdline "hugepages=$NR_HUGEPAGE"
+        update_grub_cmdline "default_hugepagesz=1G"
+        if ! grep -q "^vm.nr_hugepages" /etc/sysctl.conf; then
+                echo "vm.nr_hugepages=$NR_HUGEPAGE" >> /etc/sysctl.conf
+        fi
+else
+        echo "  OK: Hugepage is enabled"
+fi
+
+# Ensure SR-IOV is enabled
+# --------------------------
+if ! lsmod | grep -q vfio-pci; then
+        echo 'vfio-pci' | tee /etc/modules-load.d/sriov.conf 1> /dev/null
+        systemctl restart systemd-modules-load.service
+fi
+
+if ! check_vf; then
+        cp "$(cd "$(dirname "$0")" && pwd)/sriov.sh" /usr/bin/sriov.sh
+        tee "/etc/systemd/system/sriov.service" > /dev/null << EOF
+[Unit]
+Description=Create VFs on $SRIOV_PF
+
+[Service]
+Type=oneshot
+ExecStart=/usr/bin/sriov.sh -b $SRIOV_PF
+
+[Install]
+WantedBy=default.target
+EOF
+        systemctl daemon-reload
+        systemctl enable --now sriov.service &> /dev/null
+        echo "      Configured VFs on $SRIOV_PF"
+fi
+
+if check_vf; then
+        echo "  OK: SR-IOV is enabled on $SRIOV_PF"
+else
+        disabled=1
+fi
+
+if [ "$grub_updated" -eq 1 ]; then
+        update-grub &> /dev/null
+        echo "HINT: Grub was updated, reboot for changes to take effect"
+        exit 1
+fi
+
+exit $disabled
diff --git a/scripts/sriov.sh b/scripts/sriov.sh
new file mode 100755
index 0000000..a478541
--- /dev/null
+++ b/scripts/sriov.sh
@@ -0,0 +1,84 @@
+#!/bin/bash
+
+# Copyright (c) 2019 Intel Corporation
+#
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+# copied from https://github.com/clearlinux/cloud-native-setup/blob/master/clr-k8s-examples/9-multi-network/systemd/sriov.sh
+
+set -o errexit
+set -o pipefail
+set -o nounset
+set -x
+
+OPTIND=1
+bind="false"
+
+while getopts ":b" opt; do
+	case ${opt} in
+	b)
+		bind="true"
+		;;
+	\?)
+		echo "Usage: sriov.sh [-b] ens785f0 ens785f1 ..."
+		echo "-b	Bind to vfio-pci"
+		exit
+		;;
+	esac
+done
+shift $((OPTIND - 1))
+
+setup_pf() {
+	local pf=$1
+	local num_vfs
+
+	echo "Resetting PF $pf"
+	echo 0 | tee /sys/class/net/"$pf"/device/sriov_numvfs
+	num_vfs=$(cat /sys/class/net/"$pf"/device/sriov_totalvfs)
+	echo "Enabling $num_vfs VFs for $pf"
+	echo "$num_vfs" | tee /sys/class/net/"$pf"/device/sriov_numvfs
+	ip link set "$pf" up
+	sleep 1
+}
+
+vfio_bind() {
+	local pf=$1
+	local pfpci
+	local num_vfs
+
+	pfpci=$(readlink /sys/devices/pci*/*/*/net/"$pf"/device | awk '{print substr($1,10)}')
+	num_vfs=$(cat /sys/class/net/"$pf"/device/sriov_numvfs)
+
+	local vfpci
+	local mac
+	for ((idx = 0; idx < num_vfs; idx++)); do
+                #Some drivers does not support state change of VF
+		#ip link set dev $pf vf $idx state enable
+
+		local vfn="virtfn$idx"
+		# shellcheck disable=SC2012
+		vfpci=$(ls -l /sys/devices/pci*/*/"$pfpci" | awk -v vfn=$vfn 'vfn==$9 {print substr($11,4)}')
+		# Capture and set MAC of the VF before unbinding from linux, for later use in CNI
+		mac=$(cat /sys/bus/pci*/*/"$vfpci"/net/*/address)
+		ip link set dev "$pf" vf $idx mac "$mac"
+		# Bind VF to vfio-pci
+		echo "$vfpci" >/sys/bus/pci*/*/"$vfpci"/driver/unbind
+		echo "vfio-pci" >/sys/devices/pci*/*/"$vfpci"/driver_override
+		echo "$vfpci" >/sys/bus/pci/drivers/vfio-pci/bind
+	done
+}
+
+for pf in "$@"; do
+	setup_pf "$pf"
+        if [ $bind ]; then vfio_bind "$pf"; fi
+done