diff --git a/vendor/github.com/opencord/omci-lib-go/v2/generated/xdsllineconfigurationprofilepart3.go b/vendor/github.com/opencord/omci-lib-go/v2/generated/xdsllineconfigurationprofilepart3.go
new file mode 100644
index 0000000..48981e9
--- /dev/null
+++ b/vendor/github.com/opencord/omci-lib-go/v2/generated/xdsllineconfigurationprofilepart3.go
@@ -0,0 +1,218 @@
+/*
+ * Copyright (c) 2018 - present.  Boling Consulting Solutions (bcsw.net)
+ * Copyright 2020-present Open Networking Foundation
+
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+
+ * http://www.apache.org/licenses/LICENSE-2.0
+
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+/*
+ * NOTE: This file was generated, manual edits will be overwritten!
+ *
+ * Generated by 'goCodeGenerator.py':
+ *              https://github.com/cboling/OMCI-parser/README.md
+ */
+
+package generated
+
+import "github.com/deckarep/golang-set"
+
+// XdslLineConfigurationProfilePart3ClassID is the 16-bit ID for the OMCI
+// Managed entity xDSL line configuration profile part 3
+const XdslLineConfigurationProfilePart3ClassID = ClassID(106) // 0x006a
+
+var xdsllineconfigurationprofilepart3BME *ManagedEntityDefinition
+
+// XdslLineConfigurationProfilePart3 (Class ID: #106 / 0x006a)
+//	The overall xDSL line configuration profile is modelled in several parts, all of which are
+//	associated together through a common ME ID (the client PPTP xDSL UNI part 1 has a single
+//	pointer, which refers to the entire set of line configuration profile parts).
+//
+//	Relationships
+//		An instance of this ME may be associated with zero or more instances of an xDSL UNI.
+//
+//	Attributes
+//		Managed Entity Id
+//			This attribute uniquely identifies each instance of this ME. All xDSL and VDSL2 line
+//			configuration profiles and extensions that pertain to a given PPTP xDSL UNI must share a common
+//			ME ID. (R, setbycreate) (mandatory) (2-bytes)
+//
+//		Loop Diagnostics Mode Forced Ldsf
+//			Loop diagnostics mode forced (LDSF): This configuration parameter forces the line into loop
+//			diagnostic mode via the xTU-C. It is only valid for [ITUT-G.992.3], [ITUT-G.992.4] and
+//			[ITUT-G.992.5]. It is defined as follows.
+//
+//			0	Inhibits the xTU-C from performing loop diagnostic mode procedures on the line. Loop
+//			diagnostic mode procedures may still be initiated by the xTU-R.
+//
+//			1	Forces the xTU-C to perform loop diagnostics procedures.
+//
+//			Only while the line power management state is L3 can the line be forced into loop diagnostic
+//			mode. When loop diagnostic procedures complete successfully, the ONU resets this attribute to 0.
+//			The line remains in the L3 idle state. The loop diagnostics data are available at least until
+//			the line is forced to the L0 state. As long as loop diagnostic procedures have not completed
+//			successfully, attempts are made to do so, until the loop diagnostic mode is no longer forced on
+//			the line through this configuration parameter. If loop diagnostic procedures cannot be completed
+//			successfully after a vendordiscretionary number of retries or within a vendor-discretionary
+//			timeout, then an initialization failure occurs. (R,-W, setbycreate) (mandatory) (1-byte)
+//
+//		Automode Cold Start Forced
+//			This attribute is defined to improve testing of the performance of xTUs supporting automode.
+//			Valid values are 0 and 1. A change in value of this attribute indicates a change in loop
+//			conditions applied to the devices under test. The xTUs reset any historical information used for
+//			automode, for shortening an ITU-T G.994.1 handshake, or for shortening the initialization
+//			procedure.
+//
+//			Automode is defined as the case where multiple operation modes are enabled in xTSE (Table
+//			9.7.12-1) and where the selection of the operation mode to be used for transmission depends, not
+//			only on the common capabilities of both xTUs (as exchanged in [ITU-T G.994.1]), but also on
+//			achievable data rates under given loop conditions. (R,-W, setbycreate) (mandatory if automode is
+//			supported) (1-byte)
+//
+//		L2 Atpr
+//			L2ATPR:	This parameter specifies the maximum aggregate transmit power reduction that can be
+//			performed in the L2 request (i.e., at the transition of L0 to L2 state) or through a single
+//			power trim in the L2 state. It is only valid for [ITUT-G.992.3], [ITUT-G.992.4] and
+//			[ITUT-G.992.5]. This attribute ranges from 0 (0-dB) dB to 31 (31-dB). (R, W, setbycreate)
+//			(mandatory) (1 byte)
+//
+//		L2 Atprt
+//			L2ATPRT:	This parameter specifies the total maximum aggregate transmit power reduction (in
+//			decibels) that can be performed in an L2 state. This is the sum of all reductions of L2 requests
+//			(i.e., at transitions from L0 to L2 state) and power trims. This attribute ranges from 0 (0 dB)
+//			dB to 31 (31 dB). (R, W, setbycreate) (mandatory) (1 byte)
+//
+//		Force Inp Downstream
+//			When set to 1, the FORCEINPds attribute forces the framer settings of all downstream bearer
+//			channels to be selected such that the impulse noise protection (INP) computed according to the
+//			formula specified in the relevant Recommendation is greater than or equal to the minimal INP
+//			requirement. The default value 0 disables this function. (R, W) (mandatory for [ITU-T G.993.2],
+//			optional for other Recommendations that support it) (1 byte)
+//
+//		Force Inp Upstream
+//			When set to 1, the FORCEINPus attribute forces the framer settings of all upstream bearer
+//			channels to be selected such that the INP computed according to the formula specified in the
+//			relevant Recommendation is greater than or equal to the minimal INP requirement. The default
+//			value 0 disables this function. (R, W) (mandatory for [ITU-T G.993.2], optional for other
+//			Recommendations that support it) (1 byte)
+//
+//		Update Request Flag For Near_End Test Parameters
+//			Update request flag for near-end test parameters: The UPDATE-TEST-NE attribute forces an update
+//			of all near-end test parameters that can be updated during showtime in [ITU-T G.993.2]. Update
+//			is triggered by setting this attribute to 1, whereupon the near-end test parameters are expected
+//			to be updated within 10-s, and the ONU should reset the attribute value to 0. The update request
+//			flag is independent of any autonomous update process in the system. The update request attribute
+//			must be prepared to accept another set after a period not to exceed 3-min, a period that starts
+//			when the flag is set via the OMCI or by an autonomous process in the system. (R,-W) (optional)
+//			(1-byte)
+//
+//		Update Request Flag For Far_End Test Parameters
+//			Update request flag for far-end test parameters: The UPDATE-TEST-FE attribute forces an update
+//			of all far-end test parameters that can be updated during showtime in [ITU-T G.993.2]. Update is
+//			triggered by setting this attribute to 1, whereupon the far-end test parameters are expected to
+//			be updated within 10-s, and the ONU should reset the attribute value to 0. The update request
+//			flag is independent of any autonomous update process in the system. The update request attribute
+//			must be prepared to accept another set after a period not to exceed 3-min, a period that starts
+//			when the flag is set via the OMCI or by an autonomous process in the system. (R,-W) (optional)
+//			(1-byte)
+//
+//			The following eight attributes configure the impulse noise monitoring (INM) function, whose
+//			results are available via the xDSL impulse noise monitor PM history data ME. The downstream
+//			attributes are applicable to [ITUT G.993.2], [ITUT G.992.3] and [ITUT G.992.5]. Only [ITUT
+//			G.993.2] supports the upstream attributes.
+//
+//		Inm Inter Arrival Time Offset Upstream
+//			INM inter-arrival time offset upstream: INMIATOus is the inter-arrival time (IAT) offset that
+//			the xTU-C receiver uses to determine in which bin of the IAT histogram the IAT is reported.
+//			Valid values for INMIATO range from 3 to 511 discrete multi-tone (DMT) symbols in steps of 1 DMT
+//			symbol. (R,-W) (optional) (2-bytes)
+//
+//		Inm Inter_Arrival Time Step Upstream
+//			INM inter-arrival time step upstream: INMIATSus is the IAT step that the xTU-C receiver uses to
+//			determine in which bin of the IAT histogram the IAT is reported. Valid values for INMIATS range
+//			from 0 to 7 in steps of 1. (R,-W) (optional) (1-byte)
+//
+//		Inm Cluster Continuation Value Upstream
+//			INMCCus is the cluster continuation value that the xTU-C receiver uses in the cluster indication
+//			process described in the applicable Recommendation. Valid values for INMCC range from 0 to 64
+//			DMT symbols in steps of 1 DMT symbol. (R,-W) (optional) (1-byte)
+//
+//		Inm Equivalent Inp Mode Upstream
+//			INM_INPEQ_MODEus is the INM equivalent INP mode that the xTU-C receiver uses in the computation
+//			of the equivalent INP, as defined in the applicable Recommendation. Valid values for
+//			INM_INPEQ_MODE are 0..4. (R,-W) (optional) (1-byte)
+//
+//		Inm Inter Arrival Time Offset Downstream
+//			INM inter-arrival time offset downstream: INMIATOds is the IAT offset that the xTU-R receiver
+//			uses to determine in which bin of the IAT histogram the IAT is reported. Valid values for
+//			INMIATO range from 3 to 511 DMT symbols in steps of 1 DMT symbol. (R,-W) (optional) (2-bytes)
+//
+//		Inm Inter_Arrival Time Step Downstream
+//			INM inter-arrival time step downstream: INMIATSds is the IAT step that the xTU-R receiver uses
+//			to determine in which bin of the IAT histogram the IAT is reported. Valid values for INMIATS
+//			range from 0 to 7 in steps of 1. (R,-W) (optional) (1-byte)
+//
+//		Inm Cluster Continuation Value Downstream
+//			INMCCds is the cluster continuation value that the xTU-R receiver uses in the cluster indication
+//			process described in the applicable Recommendation. Valid values for INMCC range from 0 to 64
+//			DMT symbols in steps of 1 DMT symbol. (R,-W) (optional) (1-byte)
+//
+//		Inm Equivalent Inp Mode Downstream
+//			INM_INPEQ_MODEds is the INM equivalent INP mode that the xTU-R receiver uses in the computation
+//			of the equivalent INP, as defined in the applicable Recommendation. Valid values for
+//			INM_INPEQ_MODE are 0..4. (R,-W) (optional) (1-byte)
+//
+type XdslLineConfigurationProfilePart3 struct {
+	ManagedEntityDefinition
+	Attributes AttributeValueMap
+}
+
+func init() {
+	xdsllineconfigurationprofilepart3BME = &ManagedEntityDefinition{
+		Name:    "XdslLineConfigurationProfilePart3",
+		ClassID: 106,
+		MessageTypes: mapset.NewSetWith(
+			Create,
+			Delete,
+			Get,
+			Set,
+		),
+		AllowedAttributeMask: 0xffff,
+		AttributeDefinitions: AttributeDefinitionMap{
+			0:  Uint16Field("ManagedEntityId", PointerAttributeType, 0x0000, 0, mapset.NewSetWith(Read, SetByCreate), false, false, false, 0),
+			1:  ByteField("LoopDiagnosticsModeForcedLdsf", UnsignedIntegerAttributeType, 0x8000, 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, 1),
+			2:  ByteField("AutomodeColdStartForced", UnsignedIntegerAttributeType, 0x4000, 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, 2),
+			3:  ByteField("L2Atpr", UnsignedIntegerAttributeType, 0x2000, 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, 3),
+			4:  ByteField("L2Atprt", UnsignedIntegerAttributeType, 0x1000, 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, 4),
+			5:  ByteField("ForceInpDownstream", UnsignedIntegerAttributeType, 0x0800, 0, mapset.NewSetWith(Read, Write), false, false, false, 5),
+			6:  ByteField("ForceInpUpstream", UnsignedIntegerAttributeType, 0x0400, 0, mapset.NewSetWith(Read, Write), false, false, false, 6),
+			7:  ByteField("UpdateRequestFlagForNearEndTestParameters", UnsignedIntegerAttributeType, 0x0200, 0, mapset.NewSetWith(Read, Write), true, true, false, 7),
+			8:  ByteField("UpdateRequestFlagForFarEndTestParameters", UnsignedIntegerAttributeType, 0x0100, 0, mapset.NewSetWith(Read, Write), true, true, false, 8),
+			9:  Uint16Field("InmInterArrivalTimeOffsetUpstream", UnsignedIntegerAttributeType, 0x0080, 0, mapset.NewSetWith(Read, Write), false, true, false, 9),
+			10: ByteField("InmInterArrivalTimeStepUpstream", UnsignedIntegerAttributeType, 0x0040, 0, mapset.NewSetWith(Read, Write), false, true, false, 10),
+			11: ByteField("InmClusterContinuationValueUpstream", UnsignedIntegerAttributeType, 0x0020, 0, mapset.NewSetWith(Read, Write), false, true, false, 11),
+			12: ByteField("InmEquivalentInpModeUpstream", UnsignedIntegerAttributeType, 0x0010, 0, mapset.NewSetWith(Read, Write), false, true, false, 12),
+			13: Uint16Field("InmInterArrivalTimeOffsetDownstream", UnsignedIntegerAttributeType, 0x0008, 0, mapset.NewSetWith(Read, Write), false, true, false, 13),
+			14: ByteField("InmInterArrivalTimeStepDownstream", UnsignedIntegerAttributeType, 0x0004, 0, mapset.NewSetWith(Read, Write), false, true, false, 14),
+			15: ByteField("InmClusterContinuationValueDownstream", UnsignedIntegerAttributeType, 0x0002, 0, mapset.NewSetWith(Read, Write), false, true, false, 15),
+			16: ByteField("InmEquivalentInpModeDownstream", UnsignedIntegerAttributeType, 0x0001, 0, mapset.NewSetWith(Read, Write), false, true, false, 16),
+		},
+		Access:  CreatedByOlt,
+		Support: UnknownSupport,
+	}
+}
+
+// NewXdslLineConfigurationProfilePart3 (class ID 106) creates the basic
+// Managed Entity definition that is used to validate an ME of this type that
+// is received from or transmitted to the OMCC.
+func NewXdslLineConfigurationProfilePart3(params ...ParamData) (*ManagedEntity, OmciErrors) {
+	return NewManagedEntity(*xdsllineconfigurationprofilepart3BME, params...)
+}