Committing vendored dependencies and generated protos
Change-Id: I349c149b513d9de7d9f60bde2c954a939da2fc54
diff --git a/vendor/github.com/cboling/omci/generated/reani-g.go b/vendor/github.com/cboling/omci/generated/reani-g.go
new file mode 100644
index 0000000..7ee4996
--- /dev/null
+++ b/vendor/github.com/cboling/omci/generated/reani-g.go
@@ -0,0 +1,188 @@
+/*
+ * Copyright (c) 2018 - present. Boling Consulting Solutions (bcsw.net)
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ * http://www.apache.org/licenses/LICENSE-2.0
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+/*
+ * NOTE: This file was generated, manual edits will be overwritten!
+ *
+ * Generated by 'goCodeGenerator.py':
+ * https://github.com/cboling/OMCI-parser/README.md
+ */
+package generated
+
+import "github.com/deckarep/golang-set"
+
+const ReAniGClassId ClassID = ClassID(313)
+
+var reanigBME *ManagedEntityDefinition
+
+// ReAniG (class ID #313)
+// This ME organizes data associated with each R'/S' physical interface of an RE if the RE supports
+// OEO regeneration in either direction. The management ONU automatically creates one instance of
+// this ME for each R'/S' physical port (uni- or bidirectional) as follows.
+//
+// • When the RE has mid-span PON RE ANI interface ports built into its factory configuration.
+//
+// • When a cardholder is provisioned to expect a circuit pack of the mid-span PON RE ANI type.
+//
+// • When a cardholder provisioned for plug-and-play is equipped with a circuit pack of the midspan
+// PON RE ANI type. Note that the installation of a plug-and-play card may indicate the presence of
+// a mid-span PON RE ANI port via equipment ID as well as its type attribute, and indeed may cause
+// the management ONU to instantiate a port-mapping package to specify the ports precisely.
+//
+// The management ONU automatically deletes instances of this ME when a cardholder is neither
+// provisioned to expect a mid-span PON RE ANI circuit pack, nor is it equipped with a mid-span PON
+// RE ANI circuit pack.
+//
+// As illustrated in Figure 8.2.10-4, an RE ANI-G may share the physical port with an RE downstream
+// amplifier. The ONU declares a shared configuration through the port-mapping package combined
+// port table, whose structure defines one ME as the master. It is recommended that the RE ANI-G be
+// the master, with the RE downstream amplifier as a secondary ME.
+//
+// The administrative state, operational state and ARC attributes of the master ME override similar
+// attributes in secondary MEs associated with the same port. In the secondary ME, these attributes
+// are present, but cause no action when written and have undefined values when read. The RE
+// downstream amplifier should use its provisionable downstream alarm thresholds and should declare
+// downstream alarms as necessary; other isomorphic alarms should be declared by the RE ANI-G. The
+// test action should be addressed to the master ME.
+//
+// Relationships
+// An instance of this ME is associated with each R'/S' physical interface of an RE that includes
+// OEO regeneration in either direction, and with one or more instances of the PPTP RE UNI. It may
+// also be associated with an RE downstream amplifier.
+//
+// Attributes
+// Managed Entity Id
+// NOTE 1 – This ME ID may be identical to that of an RE downstream amplifier if it shares the same
+// physical slot and port.
+//
+// Administrative State
+// NOTE 2 – When an RE supports multiple PONs, or protected access to a single PON, its primary
+// ANI-G cannot be completely shut down, due to a loss of the management communications capability.
+// Complete blocking of service and removal of power may nevertheless be appropriate for secondary
+// RE ANI-Gs. Administrative lock suppresses alarms and notifications for an RE ANI-G, be it either
+// primary or secondary.
+//
+// Operational State
+// Operational state: This attribute indicates whether the ME is capable of performing its
+// function. Valid values are enabled (0) and disabled (1). (R) (optional) (1 byte)
+//
+// Arc
+// ARC: See clause A.1.4.3. (R, W) (optional) (1 byte)
+//
+// Arc Interval
+// ARC interval: See clause A.1.4.3. (R, W) (optional) (1 byte)
+//
+// Optical Signal Level
+// Optical signal level: This attribute reports the current measurement of total downstream optical
+// power. Its value is a 2s complement integer referred to 1 mW (i.e., dBm), with 0.002 dB
+// granularity. (R) (optional) (2 bytes)
+//
+// Lower Optical Threshold
+// Lower optical threshold: This attribute specifies the optical level that the RE uses to declare
+// the downstream low received optical power alarm. Valid values are –127 dBm (coded as 254) to
+// 0 dBm (coded as 0) in 0.5 dB increments. The default value 0xFF selects the RE's internal
+// policy. (R, W) (optional) (1 byte)
+//
+// Upper Optical Threshold
+// Upper optical threshold: This attribute specifies the optical level that the RE uses to declare
+// the downstream high received optical power alarm. Valid values are –127 dBm (coded as 254) to
+// 0 dBm (coded as 0) in 0.5 dB increments. The default value 0xFF selects the RE's internal
+// policy. (R, W) (optional) (1 byte)
+//
+// Transmit Optical Level
+// Transmit optical level: This attribute reports the current measurement of mean optical launch
+// power. Its value is a 2s complement integer referred to 1 mW (i.e., dBm), with 0.002 dB
+// granularity. (R) (optional) (2 bytes)
+//
+// Lower Transmit Power Threshold
+// Lower transmit power threshold: This attribute specifies the minimum mean optical launch power
+// that the RE uses to declare the low transmit optical power alarm. Its value is a 2s complement
+// integer referred to 1 mW (i.e., dBm), with 0.5 dB granularity. The default value 0x7F selects
+// the RE's internal policy. (R, W) (optional) (1 byte)
+//
+// Upper Transmit Power Threshold
+// Upper transmit power threshold: This attribute specifies the maximum mean optical launch power
+// that the RE uses to declare the high transmit optical power alarm. Its value is a 2s complement
+// integer referred to 1 mW (i.e., dBm), with 0.5 dB granularity. The default value 0x7F selects
+// the RE's internal policy. (R, W) (optional) (1 byte)
+//
+// Usage Mode
+// 3 This R'/S' interface is used as the uplink for both the embedded management ONU and one or
+// more PPTP RE UNI(s) (in a time division fashion).
+//
+// Target Upstream Frequency
+// Target upstream frequency: This attribute specifies the frequency of the converted upstream
+// signal on the optical trunk line (OTL), in gigahertz. The converted frequency must conform to
+// the frequency plan specified in [ITUT G.984.6]. The value 0 means that the upstream signal
+// frequency remains the same as the original frequency; no frequency conversion is done. If the RE
+// does not support provisionable upstream frequency (wavelength), this attribute should take the
+// fixed value representing the RE's capability and the RE should deny attempts to set the value of
+// the attribute. If the RE does support provisionable upstream frequency conversion, the default
+// value of this attribute is 0. (R, W) (optional) (4 bytes).
+//
+// Target Downstream Frequency
+// Target downstream frequency: This attribute specifies the frequency of the downstream signal
+// received by the RE on the OTL, in gigahertz. The incoming frequency must conform to the
+// frequency plan specified in [ITUT G.984.6]. The default value 0 means that the downstream
+// frequency remains the same as its original frequency; no frequency conversion is done. If the RE
+// does not support provisionable downstream frequency selectivity, this attribute should take the
+// fixed value representing the RE's capability, and the RE should deny attempts to set the value
+// of the attribute. If the RE does support provisionable downstream frequency selectivity, the
+// default value of this attribute is 0. (R, W) (optional) (4 bytes).
+//
+// Upstream Signal Transmission Mode
+// Upstream signal transmission mode: When true, this Boolean attribute enables conversion from
+// burst mode to continuous mode. The default value false specifies burst mode upstream
+// transmission. If the RE does not have the ability to convert from burst to continuous mode
+// transmission, it should deny attempts to set this attribute to true. (R, W) (optional) (1 byte)
+//
+type ReAniG struct {
+ ManagedEntityDefinition
+ Attributes AttributeValueMap
+}
+
+func init() {
+ reanigBME = &ManagedEntityDefinition{
+ Name: "ReAniG",
+ ClassID: 313,
+ MessageTypes: mapset.NewSetWith(
+ Get,
+ Set,
+ ),
+ AllowedAttributeMask: 0XFFFC,
+ AttributeDefinitions: AttributeDefinitionMap{
+ 0: Uint16Field("ManagedEntityId", 0, mapset.NewSetWith(Read), false, false, false, false, 0),
+ 1: ByteField("AdministrativeState", 0, mapset.NewSetWith(Read, Write), false, false, false, false, 1),
+ 2: ByteField("OperationalState", 0, mapset.NewSetWith(Read), true, false, true, false, 2),
+ 3: ByteField("Arc", 0, mapset.NewSetWith(Read, Write), true, false, true, false, 3),
+ 4: ByteField("ArcInterval", 0, mapset.NewSetWith(Read, Write), false, false, true, false, 4),
+ 5: Uint16Field("OpticalSignalLevel", 0, mapset.NewSetWith(Read), false, false, true, false, 5),
+ 6: ByteField("LowerOpticalThreshold", 0, mapset.NewSetWith(Read, Write), false, false, true, false, 6),
+ 7: ByteField("UpperOpticalThreshold", 0, mapset.NewSetWith(Read, Write), false, false, true, false, 7),
+ 8: Uint16Field("TransmitOpticalLevel", 0, mapset.NewSetWith(Read), false, false, true, false, 8),
+ 9: ByteField("LowerTransmitPowerThreshold", 0, mapset.NewSetWith(Read, Write), false, false, true, false, 9),
+ 10: ByteField("UpperTransmitPowerThreshold", 0, mapset.NewSetWith(Read, Write), false, false, true, false, 10),
+ 11: ByteField("UsageMode", 0, mapset.NewSetWith(Read, Write), false, false, false, false, 11),
+ 12: Uint32Field("TargetUpstreamFrequency", 0, mapset.NewSetWith(Read, Write), false, false, true, false, 12),
+ 13: Uint32Field("TargetDownstreamFrequency", 0, mapset.NewSetWith(Read, Write), false, false, true, false, 13),
+ 14: ByteField("UpstreamSignalTransmissionMode", 0, mapset.NewSetWith(Read, Write), false, false, true, false, 14),
+ },
+ }
+}
+
+// NewReAniG (class ID 313 creates the basic
+// Managed Entity definition that is used to validate an ME of this type that
+// is received from the wire, about to be sent on the wire.
+func NewReAniG(params ...ParamData) (*ManagedEntity, OmciErrors) {
+ return NewManagedEntity(reanigBME, params...)
+}