diff --git a/jjb/pipeline/voltha-dt-physical-build-and-tests.groovy b/jjb/pipeline/voltha-dt-physical-build-and-tests.groovy
new file mode 100644
index 0000000..916fe18
--- /dev/null
+++ b/jjb/pipeline/voltha-dt-physical-build-and-tests.groovy
@@ -0,0 +1,435 @@
+// Copyright 2019-present Open Networking Foundation
+//
+// Licensed under the Apache License, Version 2.0 (the "License");
+// you may not use this file except in compliance with the License.
+// You may obtain a copy of the License at
+//
+// http://www.apache.org/licenses/LICENSE-2.0
+//
+// Unless required by applicable law or agreed to in writing, software
+// distributed under the License is distributed on an "AS IS" BASIS,
+// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+// See the License for the specific language governing permissions and
+// limitations under the License.
+
+// deploy VOLTHA built from patchset on a physical pod and run e2e test
+// uses kind-voltha to deploy voltha-2.X
+
+// Need this so that deployment_config has global scope when it's read later
+deployment_config = null
+localDeploymentConfigFile = null
+localKindVolthaValuesFile = null
+localSadisConfigFile = null
+
+// The pipeline assumes these variables are always defined
+if ( params.manualBranch != "" ) {
+  GERRIT_EVENT_COMMENT_TEXT = ""
+  GERRIT_PROJECT = ""
+  GERRIT_BRANCH = "${params.manualBranch}"
+  GERRIT_CHANGE_NUMBER = ""
+  GERRIT_PATCHSET_NUMBER = ""
+}
+
+pipeline {
+
+  /* no label, executor is determined by JJB */
+  agent {
+    label "${params.buildNode}"
+  }
+  options {
+      timeout(time: 120, unit: 'MINUTES')
+  }
+
+  environment {
+    KUBECONFIG="$HOME/.kube/kind-config-voltha-minimal"
+    VOLTCONFIG="$HOME/.volt/config-minimal"
+    PATH="$WORKSPACE/voltha/kind-voltha/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin"
+    TYPE="minimal"
+    FANCY=0
+    //VOL-2194 ONOS SSH and REST ports hardcoded to 30115/30120 in tests
+    ONOS_SSH_PORT=30115
+    ONOS_API_PORT=30120
+  }
+
+  stages {
+    stage ('Initialize') {
+      steps {
+        sh returnStdout: false, script: """
+        test -e $WORKSPACE/voltha/kind-voltha/voltha && cd $WORKSPACE/voltha/kind-voltha && ./voltha down
+        cd $WORKSPACE
+        rm -rf $WORKSPACE/*
+        """
+        script {
+          if (env.configRepo && ! env.localConfigDir) {
+            env.localConfigDir = "$WORKSPACE"
+            sh returnStdout: false, script: "git clone -b master ${cordRepoUrl}/${configRepo}"
+          }
+          localDeploymentConfigFile = "${env.localConfigDir}/${params.deploymentConfigFile}"
+          localKindVolthaValuesFile = "${env.localConfigDir}/${params.kindVolthaValuesFile}"
+          localSadisConfigFile = "${env.localConfigDir}/${params.sadisConfigFile}"
+        }
+      }
+    }
+
+    stage('Repo') {
+      steps {
+        checkout(changelog: true,
+          poll: false,
+          scm: [$class: 'RepoScm',
+            manifestRepositoryUrl: "${params.manifestUrl}",
+            manifestBranch: "${params.branch}",
+            currentBranch: true,
+            destinationDir: 'voltha',
+            forceSync: true,
+            resetFirst: true,
+            quiet: true,
+            jobs: 4,
+            showAllChanges: true]
+          )
+      }
+    }
+
+    stage('Get Patch') {
+      when {
+        expression { params.manualBranch == "" }
+      }
+      steps {
+        sh returnStdout: false, script: """
+        cd voltha
+        repo download "${gerritProject}" "${gerritChangeNumber}/${gerritPatchsetNumber}"
+        """
+      }
+    }
+
+    stage('Check config files') {
+      steps {
+        script {
+          try {
+            deployment_config = readYaml file: "${localDeploymentConfigFile}"
+          } catch (err) {
+            echo "Error reading ${localDeploymentConfigFile}"
+            throw err
+          }
+          sh returnStdout: false, script: """
+          if [ ! -e ${localKindVolthaValuesFile} ]; then echo "${localKindVolthaValuesFile} not found"; exit 1; fi
+          if [ ! -e ${localSadisConfigFile} ]; then echo "${localSadisConfigFile} not found"; exit 1; fi
+          """
+        }
+      }
+    }
+
+    stage('Create KinD Cluster') {
+      steps {
+        sh returnStdout: false, script: """
+        if [ "${branch}" != "master" ]; then
+          echo "on branch: ${branch}, sourcing kind-voltha/releases/${branch}"
+          source "$WORKSPACE/voltha/kind-voltha/releases/${branch}"
+        else
+          echo "on master, using default settings for kind-voltha"
+        fi
+
+        cd $WORKSPACE/voltha/kind-voltha/
+        JUST_K8S=y ./voltha up
+        """
+      }
+    }
+
+    stage('Build and Push Images') {
+      when {
+        expression { params.manualBranch == "" }
+      }
+      steps {
+        sh returnStdout: false, script: """
+
+        if [ "${branch}" != "master" ]; then
+          echo "on branch: ${branch}, sourcing kind-voltha/releases/${branch}"
+          source "$WORKSPACE/voltha/kind-voltha/releases/${branch}"
+        else
+          echo "on master, using default settings for kind-voltha"
+        fi
+
+        if ! [[ "${gerritProject}" =~ ^(voltha-system-tests|kind-voltha|voltha-helm-charts)\$ ]]; then
+          make -C $WORKSPACE/voltha/${gerritProject} DOCKER_REPOSITORY=voltha/ DOCKER_TAG=citest docker-build
+          docker images | grep citest
+          for image in \$(docker images -f "reference=*/*citest" --format "{{.Repository}}")
+          do
+            echo "Pushing \$image to nodes"
+            kind load docker-image \$image:citest --name voltha-\$TYPE --nodes voltha-\$TYPE-worker,voltha-\$TYPE-worker2
+            docker rmi \$image:citest \$image:latest || true
+          done
+        fi
+        """
+      }
+    }
+
+    stage('Deploy Voltha') {
+      environment {
+        WITH_RADIUS="no"
+        WITH_EAPOL="no"
+        WITH_DHCP="no"
+        WITH_IGMP="no"
+        CONFIG_SADIS="no"
+        WITH_SIM_ADAPTERS="no"
+        DEPLOY_K8S="no"
+        VOLTHA_LOG_LEVEL="DEBUG"
+      }
+      steps {
+        script {
+          sh returnStdout: false, script: """
+          if [ "${branch}" != "master" ]; then
+            echo "on branch: ${branch}, sourcing kind-voltha/releases/${branch}"
+            source "$WORKSPACE/voltha/kind-voltha/releases/${branch}"
+          else
+            echo "on master, using default settings for kind-voltha"
+          fi
+
+          export EXTRA_HELM_FLAGS+='--set log_agent.enabled=False -f ${localKindVolthaValuesFile} '
+
+          IMAGES=""
+          if [ "${gerritProject}" = "voltha-go" ]; then
+              IMAGES="rw_core ro_core "
+          elif [ "${gerritProject}" = "ofagent-py" ]; then
+              IMAGES="ofagent "
+          elif [ "${gerritProject}" = "voltha-onos" ]; then
+              IMAGES="onos "
+          elif [ "${gerritProject}" = "voltha-openolt-adapter" ]; then
+              IMAGES="adapter_open_olt "
+          elif [ "${gerritProject}" = "voltha-openonu-adapter" ]; then
+              IMAGES="adapter_open_onu "
+          elif [ "${gerritProject}" = "voltha-api-server" ]; then
+              IMAGES="afrouter afrouterd "
+          else
+              echo "No images to push"
+          fi
+
+          for I in \$IMAGES
+          do
+              EXTRA_HELM_FLAGS+="--set images.\$I.tag=citest,images.\$I.pullPolicy=Never "
+          done
+
+          if [ "${gerritProject}" = "voltha-helm-charts" ]; then
+              export CHART_PATH=$WORKSPACE/voltha/voltha-helm-charts
+              export VOLTHA_CHART=\$CHART_PATH/voltha
+              export VOLTHA_ADAPTER_OPEN_OLT_CHART=\$CHART_PATH/voltha-adapter-openolt
+              export VOLTHA_ADAPTER_OPEN_ONU_CHART=\$CHART_PATH/voltha-adapter-openonu
+              helm dep update \$VOLTHA_CHART
+              helm dep update \$VOLTHA_ADAPTER_OPEN_OLT_CHART
+              helm dep update \$VOLTHA_ADAPTER_OPEN_ONU_CHART
+          fi
+
+          cd $WORKSPACE/voltha/kind-voltha/
+          echo \$EXTRA_HELM_FLAGS
+          kail -n voltha -n default > $WORKSPACE/onos-voltha-combined.log &
+          ./voltha up
+
+          set +e
+
+          # Remove noise from voltha-core logs
+          voltctl log level set WARN read-write-core#github.com/opencord/voltha-go/db/model
+          voltctl log level set WARN read-write-core#github.com/opencord/voltha-lib-go/v3/pkg/kafka
+          # Remove noise from openolt logs
+          voltctl log level set WARN adapter-open-olt#github.com/opencord/voltha-lib-go/v3/pkg/db
+          voltctl log level set WARN adapter-open-olt#github.com/opencord/voltha-lib-go/v3/pkg/probe
+          voltctl log level set WARN adapter-open-olt#github.com/opencord/voltha-lib-go/v3/pkg/kafka
+          """
+        }
+      }
+    }
+
+    stage('Deploy Kafka Dump Chart') {
+      steps {
+        script {
+          sh returnStdout: false, script: """
+              helm repo add cord https://charts.opencord.org
+              helm repo update
+              if helm version -c --short|grep v2 -q; then
+                helm install -n voltha-kafka-dump cord/voltha-kafka-dump
+              else
+                helm install voltha-kafka-dump cord/voltha-kafka-dump
+              fi
+          """
+        }
+      }
+    }
+
+    stage('Push Tech-Profile') {
+      when {
+        expression { params.profile != "Default" }
+      }
+      steps {
+        sh returnStdout: false, script: """
+        etcd_container=\$(kubectl get pods -n voltha | grep voltha-etcd-cluster | awk 'NR==1{print \$1}')
+        kubectl cp $WORKSPACE/voltha/voltha-system-tests/tests/data/TechProfile-${profile}.json voltha/\$etcd_container:/tmp/flexpod.json
+        kubectl exec -it \$etcd_container -n voltha -- /bin/sh -c 'cat /tmp/flexpod.json | ETCDCTL_API=3 etcdctl put service/voltha/technology_profiles/XGS-PON/64'
+        """
+      }
+    }
+
+    stage('Push Sadis-config') {
+      steps {
+        sh returnStdout: false, script: """
+        curl -sSL --user karaf:karaf -X POST -H Content-Type:application/json http://${deployment_config.nodes[0].ip}:$ONOS_API_PORT/onos/v1/network/configuration --data @${localSadisConfigFile}
+        """
+      }
+    }
+
+    stage('Reinstall OLT software') {
+      when {
+        expression { params.reinstallOlt }
+      }
+      steps {
+        script {
+          deployment_config.olts.each { olt ->
+            sh returnStdout: false, script: "sshpass -p ${olt.pass} ssh -l ${olt.user} ${olt.ip} 'dpkg --remove asfvolt16 && dpkg --purge asfvolt16'"
+            waitUntil {
+              olt_sw_present = sh returnStdout: true, script: "sshpass -p ${olt.pass} ssh -l ${olt.user} ${olt.ip} 'dpkg --list | grep asfvolt16 | wc -l'"
+              return olt_sw_present.toInteger() == 0
+            }
+            if ( params.branch == 'voltha-2.3' ) {
+              oltDebVersion = oltDebVersionVoltha23
+            } else {
+              oltDebVersion = oltDebVersionMaster
+            }
+            sh returnStdout: false, script: "sshpass -p ${olt.pass} ssh -l ${olt.user} ${olt.ip} 'dpkg --install ${oltDebVersion}'"
+            waitUntil {
+              olt_sw_present = sh returnStdout: true, script: "sshpass -p ${olt.pass} ssh -l ${olt.user} ${olt.ip} 'dpkg --list | grep asfvolt16 | wc -l'"
+              return olt_sw_present.toInteger() == 1
+            }
+            if ( olt.fortygig ) {
+              // If the OLT is connected to a 40G switch interface, set the NNI port to be downgraded
+              sh returnStdout: false, script: "sshpass -p ${olt.pass} ssh -l ${olt.user} ${olt.ip} 'echo port ce128 sp=40000 >> /broadcom/qax.soc ; /opt/bcm68620/svk_init.sh'"
+            }
+          }
+        }
+      }
+    }
+
+    stage('Restart OLT processes') {
+      steps {
+        script {
+          deployment_config.olts.each { olt ->
+            sh returnStdout: false, script: """
+            ssh-keyscan -H ${olt.ip} >> ~/.ssh/known_hosts
+            sshpass -p ${olt.pass} ssh -l ${olt.user} ${olt.ip} 'rm -f /var/log/openolt.log; rm -f /var/log/dev_mgmt_daemon.log; reboot'
+            sleep 120
+            """
+            waitUntil {
+              onu_discovered = sh returnStdout: true, script: "sshpass -p ${olt.pass} ssh -l ${olt.user} ${olt.ip} 'grep \"onu discover indication\" /var/log/openolt.log | wc -l'"
+              return onu_discovered.toInteger() > 0
+            }
+          }
+        }
+      }
+    }
+
+    stage('Run E2E Tests') {
+      environment {
+        ROBOT_CONFIG_FILE="${localDeploymentConfigFile}"
+        ROBOT_MISC_ARGS="${params.extraRobotArgs} --removekeywords wuks -d $WORKSPACE/RobotLogs -v container_log_dir:$WORKSPACE "
+        ROBOT_FILE="Voltha_DT_PODTests.robot"
+      }
+      steps {
+        sh returnStdout: false, script: """
+        cd voltha
+        mkdir -p $WORKSPACE/RobotLogs
+
+        # If the Gerrit comment contains a line with "functional tests" then run the full
+        # functional test suite.  This covers tests tagged either 'sanity' or 'functional'.
+        # Note: Gerrit comment text will be prefixed by "Patch set n:" and a blank line
+        REGEX="functional tests"
+        if [[ "$GERRIT_EVENT_COMMENT_TEXT" =~ \$REGEX ]]; then
+          ROBOT_MISC_ARGS+="-i functionalDt"
+        fi
+
+        make -C $WORKSPACE/voltha/voltha-system-tests voltha-dt-test || true
+        """
+      }
+    }
+
+    stage('After-Test Delay') {
+      when {
+        expression { params.manualBranch == "" }
+      }
+      steps {
+        sh returnStdout: false, script: """
+        # Note: Gerrit comment text will be prefixed by "Patch set n:" and a blank line
+        REGEX="hardware test with delay\$"
+        [[ "$GERRIT_EVENT_COMMENT_TEXT" =~ \$REGEX ]] && sleep 10m || true
+        """
+      }
+    }
+  }
+
+  post {
+    always {
+      sh returnStdout: false, script: '''
+      set +e
+      cp $WORKSPACE/voltha/kind-voltha/install-minimal.log $WORKSPACE/
+      kubectl get pods --all-namespaces -o jsonpath="{range .items[*].status.containerStatuses[*]}{.image}{'\\n'}" | sort | uniq
+      kubectl get pods --all-namespaces -o jsonpath="{range .items[*].status.containerStatuses[*]}{.imageID}{'\\n'}" | sort | uniq
+      kubectl get nodes -o wide
+      kubectl get pods -o wide
+      kubectl get pods -n voltha -o wide
+
+      sync
+      pkill kail || true
+
+      ## Pull out errors from log files
+      extract_errors_go() {
+        echo
+        echo "Error summary for $1:"
+        grep $1 $WORKSPACE/onos-voltha-combined.log | grep '"level":"error"' | cut -d ' ' -f 2- | jq -r '.msg'
+        echo
+      }
+
+      extract_errors_python() {
+        echo
+        echo "Error summary for $1:"
+        grep $1 $WORKSPACE/onos-voltha-combined.log | grep 'ERROR' | cut -d ' ' -f 2-
+        echo
+      }
+
+      extract_errors_go voltha-rw-core > $WORKSPACE/error-report.log
+      extract_errors_go adapter-open-olt >> $WORKSPACE/error-report.log
+      extract_errors_python adapter-open-onu >> $WORKSPACE/error-report.log
+      extract_errors_python voltha-ofagent >> $WORKSPACE/error-report.log
+
+      gzip $WORKSPACE/onos-voltha-combined.log
+
+      ## collect events, the chart should be running by now
+      kubectl get pods | grep -i voltha-kafka-dump | grep -i running
+      if [[ $? == 0 ]]; then
+         kubectl exec -it `kubectl get pods | grep -i voltha-kafka-dump | grep -i running | cut -f1 -d " "` ./voltha-dump-events.sh > $WORKSPACE/voltha-events.log
+      fi
+      '''
+      script {
+        deployment_config.olts.each { olt ->
+          sh returnStdout: false, script: """
+          until sshpass -p ${olt.pass} scp ${olt.user}@${olt.ip}:/var/log/openolt.log $WORKSPACE/openolt-${olt.ip}.log
+          do
+              echo "Fetching openolt.log log failed, retrying..."
+              sleep 10
+          done
+          sed -i 's/\\x1b\\[[0-9;]*[a-zA-Z]//g' $WORKSPACE/openolt-${olt.ip}.log  # Remove escape sequences
+          until sshpass -p ${olt.pass} scp ${olt.user}@${olt.ip}:/var/log/dev_mgmt_daemon.log $WORKSPACE/dev_mgmt_daemon-${olt.ip}.log
+          do
+              echo "Fetching dev_mgmt_daemon.log failed, retrying..."
+              sleep 10
+          done
+          sed -i 's/\\x1b\\[[0-9;]*[a-zA-Z]//g' $WORKSPACE/dev_mgmt_daemon-${olt.ip}.log  # Remove escape sequences
+          """
+        }
+      }
+      step([$class: 'RobotPublisher',
+        disableArchiveOutput: false,
+        logFileName: 'RobotLogs/log*.html',
+        otherFiles: '',
+        outputFileName: 'RobotLogs/output*.xml',
+        outputPath: '.',
+        passThreshold: 100,
+        reportFileName: 'RobotLogs/report*.html',
+        unstableThreshold: 0]);
+      archiveArtifacts artifacts: '*.log,*.gz'
+    }
+  }
+}
diff --git a/jjb/voltha-e2e.yaml b/jjb/voltha-e2e.yaml
index 60b9506..478f17e 100644
--- a/jjb/voltha-e2e.yaml
+++ b/jjb/voltha-e2e.yaml
@@ -100,6 +100,23 @@
           oltDebVersionMaster: 'openolt_asfvolt16-2.4.9-dev-d4aeca5a2094f7dc7c519913ab1558348c546dab.deb'
           oltDebVersionVoltha23: 'openolt_asfvolt16-2.4.9-dev-d4aeca5a2094f7dc7c519913ab1558348c546dab.deb'
           profile: 'Default'
+          trigger-string: 'hardware test'
+          default-test-args: '-i sanityORDeleteOLT -X'
+
+
+      # Per-patchset Pod builds on Tucson pod
+      - 'verify_physical_voltha_patchset_manual':
+          name: 'verify_physical_voltha_patchset_manual_DT'
+          build-node: 'tucson-pod'
+          config-pod: 'tucson-pod-DT'
+          oltDebVersionMaster: 'openolt_asfvolt16-2.4.9-dev-d4aeca5a2094f7dc7c519913ab1558348c546dab.deb'
+          oltDebVersionVoltha23: 'openolt_asfvolt16-2.4.9-dev-d4aeca5a2094f7dc7c519913ab1558348c546dab.deb'
+          profile: 'Default'
+          pipeline-script: 'voltha-dt-physical-build-and-tests.groovy'
+          trigger-string: 'DT hardware test'
+          default-test-args: '-i sanityDt -X'
+
+
 
       # Manual build job for Tucson pod
       # Allow local testing without disrupting above job
@@ -306,6 +323,7 @@
                   Copyright (c) 2019 Open Networking Foundation (ONF)
     sandbox: true
     pipeline-script: 'voltha-physical-build-and-tests.groovy'
+    default-test-args: '-i sanityORDeleteOLT -X'
 
     properties:
       - cord-infra-properties:
@@ -409,7 +427,7 @@
 
       - string:
           name: extraRobotArgs
-          default: '-i sanityORDeleteOLT -X'
+          default: '{default-test-args}'
           description: 'Arguments to pass to robot'
 
     project-type: pipeline
@@ -448,6 +466,8 @@
                   Copyright (c) 2019 Open Networking Foundation (ONF)
     sandbox: true
     pipeline-script: 'voltha-physical-build-and-tests.groovy'
+    trigger-string: 'hardware test'
+    default-test-args: '-i sanityORDeleteOLT -X'
 
     properties:
       - cord-infra-properties:
@@ -551,7 +571,7 @@
 
       - string:
           name: extraRobotArgs
-          default: '-i sanityORDeleteOLT -X'
+          default: '{default-test-args}'
           description: 'Arguments to pass to robot'
 
     project-type: pipeline
@@ -564,14 +584,14 @@
           server-name: '{gerrit-server-name}'
           dependency-jobs: '{dependency-jobs}'
           silent-start: false
-          successful-message: "PASSED hardware test"
-          failure-message: "FAILED hardware test"
-          unstable-message: "UNSTABLE hardware test"
+          successful-message: "PASSED {trigger-string}"
+          failure-message: "FAILED {trigger-string}"
+          unstable-message: "UNSTABLE {trigger-string}"
           trigger-on:
             - comment-added-contains-event:
-                comment-contains-value: '^hardware test$'
+                comment-contains-value: '^{trigger-string}$'
             - comment-added-contains-event:
-                comment-contains-value: '^hardware test with delay$'
+                comment-contains-value: '^{trigger-string} with delay$'
           projects:
             - project-compare-type: REG_EXP
               project-pattern: '^(voltha-go|voltha-openolt-adapter|voltha-openonu-adapter|voltha-api-server|voltha-system-tests|ofagent-py|ofagent-go|voltha-onos|kind-voltha|voltha-helm-charts)$'