# SPDX-FileCopyrightText: 2022 Open Networking Foundation <support@opennetworking.org>
#
# SPDX-License-Identifier: BSD-3-Clause

basic:
  cell_id: 100
  mme_address: 172.21.143.206
  mme_port: 36412
  plmn_list: "305010"
  pci_list: "100,101"
  allow_enodeb_transmit: False

  carrier_number: 2
  carrier_agg_enable: False

# Automation Configuration Server
acs:
  # To enable/disable to connect the management server (ACS)
  cwmp_enable: True
  # Define to enable/disable a periodic inform
  periodic_inform_enable: True
  # Interval of a preiodic inform send to ACS
  periodic_inform_interval: 180

cell:
  # If True, 64QAM is allowed [TS 36.331]
  enable64qam: True
  # Physical Cell ID for cell 1 and cell 2
  pci1: 100
  pci2: 101
  # Tracking Area Code for cell 1 and cell 2
  tac1: 501
  tac2: 502
  # Downlink/Uplink bandwidth
  downlink_bandwidth: 25
  uplink_bandwidth: 25
  # EARFCN for 1st frequency band
  earfcn_downlink1: 55440
  earfcn_uplink1: 55440
  # EARFCN for 2nd frequency band
  earfcn_downlink2: 55640
  earfcn_uplink2: 55640
  # EARFCN for 1st + 2nd frequency band
  earfcn_downlink_list: "55440,55640"
  earfcn_uplink_list: "55440,55640"
  # First/Second Frequency Band Indicator
  frequency_band_1: 48
  frequency_band_2: 48
  # Frequency Band List
  frequency_band_list: "48, 48"
  # The DL/UL subframe configuration
  subframe_assignment: 2
  # The TDD special sub-frame pattern [TS 36.331 sec 6.3.2]
  special_subframe_pattern: 7

  # The real TX power
  tx_power: 20
  # Tunnel type
  tunnel_type: "Device.IP.Interface.1.IPv4Address.1."


# Femtocell Access Point Control Parameters
fap_control:
  # The administrative state of LTE FAP
  #  If True, the cell unlock and enable RF to serve traffic
  admin_state: False
  # Radio Resource Management
  is_ca_frequency_contiguous: 0

# Radio Environment Map Parameters
rem:
  primary_source: "FREE_RUNNING"

# Spectrum Access System (SAS)
sas:
  # If True, eNodeB will be admistrated by SAS
  sas_enable: True
  # If True, it indicates device configuration was signed by CPI key
  cpi_enable: True
  # If True, add manufacturer name as prefix of Serial Number
  manufacturer_prefix_enable: True
  # The SAS server address
  sas_server_url: "https://sas.goog/v1.2/"
  # The username registered to SAS
  sas_uid: "aether"
  # Define device's SAS category [CFR 96.39(c)]
  sas_category: "A"
  # PAL or GAA
  sas_channel_type: "GAA"
  # The device's certification name, it uses to communicate with SAS server
  sas_cert_subject: "ENODEBD_CONFIGURED_SAS_CERT"
  # Location: indoor / outdoor
  sas_location: "indoor"
  # AGL or AMSL
  sas_height_type: "AGL"
  # FCC ID of device
  sas_fccid: "ENODEBD_CONFIGURED_FCCID"
  # RECEIVED_POWER_WITH_GRANT / RECEIVED_POWER_WITHOUT_GRANT
  sas_measure_capability: "RECEIVED_POWER_WITHOUT_GRANT"
  # Your CPI name
  sas_cpi_name: "ONF_CPI"
  # Your CPI Certification ID
  sas_cpi_id: "GOOG-999999"
  # Device antenna parameters
  sas_antenna_azimuth: 0
  sas_antenna_downtilt: 0
  sas_antenna_gain: 5
  sas_antenna_beamwidth: 360
  # The signature of configuration
  sas_cpi_signature_data: "ENODEBD_CONFIGURED_CPI_SIGNED_DATA"