OFTest OpenFlow Testing Framework

Introduction

OFTest is a Python based framework for OpenFlow switch testing.

In this project we use OFTest to ensure OpenFlow conformance of the switches used to implement the network infrastructure of the OpenCord project.

At this moment the switches supported are Accton switches. For more information abot that check the wiki page at wiki.opencord.org

This code base was forked from macauleycheng which was forked from floodlight. This documentationn aims to describe the specific test cases developed for OpenCord. To get started on the basics of OFTest please check their documentation.

How it is organized

This codebase is organized by branches. Each OFDPA release correspond to a different branch. At this moment the following releases are available:

OFDPA version	Branch	Status
i19	i19	Archived
i12	i12	Archived
i12_1.7	cord-1.0	Released
2.0 GA	2.0-ga	Archived
3.0 EA0	master	Developing <- current branch

The test case collection for OpenCord are under the folder ofdpa. They are listed under the section Test case collection.

Installing Prerequisites

Following packages need to be installed before running OFTest:

sudo apt-get install python python-pip python-dev python-lxml -y
sudo pip install ncclient
sudo pip install scapy pycripto
sudo apt-get install python-ecdsa git

Start Testing

On the switch side:

Purge the switch flow/group table by running
```
	client_cfg_purge
```

Connect the switch to the testing controller

	brcm-indigo-ofdpa-ofagent -t <controller_ip>

On the controller side:

Clone the source code and switch to the correct branch

	git clone -b master git://github.com/opencord/fabric-oftest

Run all test cases in OFTest
```
	sudo ./oft -V1.3 --test-dir=ofdpa flows -i 24@eth1 -i 12@eth2
```
This command assumes you connected the switch port 24 to interface eth1 on the OFtest server and port 12 to eth2

Useful commands

List all available test cases
```
	./oft --list --test-dir=ofdpa flows
```

Run only specific test case

	sudo ./oft -V1.3 --test-dir=ofdpa flows.PacketInArp -i 24@eth1 -i 12@eth2

Test Result Summary

The following tests are implemented and these are their results.

Test Results	i12_1.7	2.0 GA	3.0 EA0
/0Ucast	X	ok	ok
/24UnicastTagged	ok	ok	ok
/32UnicastTagged	ok	ok	ok
/24ECMPL3	ok	ok	ok
/32ECMPL3	ok	ok	ok
/24ECMPVPN	ok	ok	ok
/32ECMPVPN	ok	ok	ok
/32VPN	ok	ok	ok
/24VPN	ok	ok	ok
EcmpGroupMod	X	X	ok
PacketInArp	ok	ok	ok
MTU1500	ok	ok	ok
MplsTermination	ok	ok	ok
MplsFwd	X	ok	ok
L2FloodQinQ	ok	ok	ok
L2UnicastTagged	ok	ok	ok
L3McastToL3	ok	X	ok
L3McastToL2_1*	?	?	ok
L3McastToL2_2**	?	?	ok
L3McastToL2_3***	?	?	ok
L3McastToL2_4****	ok	?	ok
L3McastToL2_5*****	?	?	ok
FloodGroupMod	X	X	ok
PacketInUDP	ok	ok	ok
Unfiltered	X	ok	X
Untagged	ok	n/a	ok

  Untag -> Untag (4094 as internal vlan)

** Untag -> Tag *** Tag -> Untag **** Tag -> Tag ***** Tag -> Tag (Translated)

n/a means test is not available for that version of the pipeline.

VLAN Test Result Summary

The following tests are implemented in vlan_flows.py and these are their results.

Test Results	3.0 EA0
L2ForwardingStackedVLAN1	ok
L2ForwardingStackedVLAN2	ok
L2ForwardingStackedVLAN3	ok
L2ForwardingStackedVLAN4	ok
L2ForwardingStackedVLAN5	ok

For major details on the test look the comments in the code.

Pseudowire Test Result Summary

The following tests are implemented in pw_flows.py and these are their results.

Test Results	3.0 EA0
UntaggedPWInitiation_2_Labels	ok
Untagged2PWInitiation_2_Labels	ok
UntaggedPWInitiation_3_Labels	ok
Untagged2PWInitiation_3_Labels	ok
TaggedPWInitiation_2_Labels	?
Tagged2PWInitiation_2_Labels	?
TaggedPWInitiation_3_Labels	?
Tagged2PWInitiation_3_Labels	?
DoubleTaggedPWInitiation_2_Labels	?
DoubleTagged2PWInitiation_2_Labels	?
DoubleTaggedPWInitiation_3_Labels	?
DoubleTagged2PWInitiation_3_Labels	?
IntraCO_2_Labels	ok
IntraCO_3_Labels	ok
InterCO	ok
UntaggedPWTermination	ok
Untagged2PWTermination	?
TaggedPWTermination	ok
DoubleTaggedPWTermination	ok

For major details on the test look the comments in the code.