OFTest OpenFlow Testing Framework

Introduction

OFTest is a Python based framework for OpenFlow switch testing.

In this project we use OFTest to ensure OpenFlow conformance of the switches used to implement the network infrastructure of the OpenCord project.

At this moment the switches supported are OF-DPA based Accton switches. For more information, check the wiki page at wiki.opencord.org/display/CORD/Underlay+Fabric

This code base was forked from macauleycheng which was forked from floodlight. This documentationn aims to describe the specific test cases developed for OpenCord. To get started on the basics of OFTest please check their documentation.

How it is organized

This codebase is organized by branches. Each OFDPA release correspond to a different branch. At this moment the following releases are available:

OFDPA version	Branch	Status
i19	i19	Archived
i12	i12	Archived
i12_1.7	cord-1.0	Released
2.0 GA	2.0-ga	Archived
3.0 EA4	master	Developing <- current branch

The test case collection for OpenCord are under the folder ofdpa. They are listed under the section Test case collection.

Installing Prerequisites

Following packages need to be installed before running OFTest:

sudo apt-get install python python-pip python-dev python-lxml -y
sudo pip install ncclient
sudo pip install scapy pycrypto
sudo apt-get install python-ecdsa git

Start Testing

On the switch side (for OF-DPA version 3.0 EA4):

Connect the switch to the VM running OFTest on the management network
```
	launcher ofagentapp  -t <controller_ip>
```

On the controller side:

Clone the source code and switch to the correct branch

	git clone -b master git://github.com/opencord/fabric-oftest

Run all test cases (that are not disabled) in a sequence
```
	sudo ./oft -V1.3 --test-dir=ofdpa flows -i 24@eth1 -i 12@eth2
```
This command assumes you connected the switch port 24 to interface eth1 on the OFtest server and port 12 to eth2. It runs all the tests that are in ofdpa/flows.py

Useful commands

List all available test cases

	./oft -V1.3 --list --test-dir=ofdpa flows

Run only specific test case. Can also be used to run tests that are currently disabled.
```
	sudo ./oft -V1.3 --test-dir=ofdpa flows.PacketInArp -i 24@eth1 -i 12@eth2
```
Run specific test case for a specific switch type (only special case of switch type supported are Qumran based switches)
```
	sudo ./oft -V1.3 -Y qmx --test-dir=ofdpa flows.PacketInArp -i 24@eth1 -i 12@eth2
```

Test Result Summary

The following tests are implemented and these are their results.

Test Results	i12_1.7	2.0 GA	3.0 EA0	3.0 EA4	3.0 EA4 QMX
/0Ucast	X	ok	ok	ok	X
/24UnicastTagged	ok	ok	ok	ok	X
/32UnicastTagged	ok	ok	ok	ok	X
/24ECMPL3	ok	ok	ok	ok	X
/32ECMPL3	ok	ok	ok	ok	X
/24ECMPVPN~	ok	ok	ok	ok	X
/32ECMPVPN~	ok	ok	ok	ok	X
/32VPN~	ok	ok	ok	ok	X
/24VPN~	ok	ok	ok	ok	X
EcmpGroupMod	X	X	ok	ok	X
PacketInArp	ok	ok	ok	ok	ok
MTU1500	ok	ok	ok	ok	ok
MplsTermination~	ok	ok	ok	ok	X
MplsFwd~	X	ok	ok	ok	ok
L2FloodQinQ	ok	ok	ok	ok	X
L2UnicastTagged	ok	ok	ok	ok	ok
L3McastToL3	ok	X	ok	ok	X
L3McastToL2_1*	?	?	ok	ok	X
L3McastToL2_2**	?	?	ok	ok	X
L3McastToL2_3***	?	?	ok	ok	X
L3McastToL2_4****	ok	?	ok	ok	X
L3McastToL2_5*****	?	?	ok	ok	X
FloodGroupMod	X	X	ok	ok	X
PacketInUDP	ok	ok	ok	ok	ok
Unfiltered	X	ok	X	ok	ok
Untagged	ok	n/a	ok	ok	ok
PacketInIPTable~	X	X	ok	ok	X

~       Tests marked with tilda are currently disabled because of a bug which causes
        interference with other tests. The @disabled flag will be removed once the bug is fixed.
*       Untag -> Untag (4094 as internal vlan)
**      Untag -> Tag
***     Tag   -> Untag
****    Tag   -> Tag
*****   Tag   -> Tag (Translated)

n/a means test is not available for that version of the pipeline.

VLAN Test Result Summary

The following tests are implemented in vlan_flows.py and these are their results.

Test Results	3.0 EA0	3.0 EA4
L2ForwardingStackedVLAN	ok	ok
L2ForwardingStackedVLAN2	ok	ok
L2ForwardingStackedVLAN3	ok	ok
L2ForwardingStackedVLAN4	ok	ok
L2ForwardingStackedVLAN5	ok	ok

For major details on the test look the comments in the code.

Pseudowire Test Result Summary

The following tests are implemented in pw_flows.py and these are their results.

Test Results	3.0 EA0	3.0 EA4
UntaggedPWInitiation_2_Labels	ok	ok
Untagged2PWInitiation_2_Labels	ok	ok
UntaggedPWInitiation_3_Labels	ok	ok
Untagged2PWInitiation_3_Labels	ok	ok
TaggedPWInitiation_2_Labels	x	ok*
Tagged2PWInitiation_2_Labels	x	ok*
TaggedPWInitiation_3_Labels	x	ok*
Tagged2PWInitiation_3_Labels	x	ok*
DoubleTaggedPWInitiation_2_Labels	x	ok*
DoubleTagged2PWInitiation_2_Labels	x	ok*
DoubleTaggedPWInitiation_3_Labels	x	ok*
DoubleTagged2PWInitiation_3_Labels	x	ok*
IntraCO_2_Labels	ok	ok*
IntraCO_3_Labels	ok	ok*
InterCO	ok	ok*
UntaggedPWTermination	ok	ok
Untagged2PWTermination	x	x
TaggedPWTermination	ok	ok
DoubleTaggedPWTermination	ok	ok
BoSBug	x	x

The test may fail intermittently

For major details on the test look the comments in the code.

IPv6 Test Result Summary

The following tests are implemented in ipv6_flows.py and these are their results.

Test Results	3.0 EA0	3.0 EA4
PacketInICMPv6	ok	ok
PacketInIPv6Table	ok	ok
_128UcastUnTagged	ok	ok
_128ECMPVpn	ok	ok
_128ECMPL3	ok	ok
_64UcastUntagged	ok	ok
_64ECMPVpn	ok	ok
_64ECMPL3	ok	ok
_0UcastV6	ok	ok
_MPLSTerminationV6	ok	ok

For major details on the test look the comments in the code.