The Fabric service is responsible for configuring the fabric switches in ONOS.
At this point we assume you followed the Fabric setup guide and your physical infrastructure is configured and ready to go.
The fabric service is composed of the following models:
FabricService. Global service-related parameters such as the name of the serviceautoconfig. Determines whether the fabric is automatically configured.Switch. Represents a fabric switch.name. Name of switch.ofId. Openflow ID of switch.driver. Driver used by the SDN controller, defaults to ofdpa3.ipv4NodeSid. MPLS label used by the switch.ipv4Loopback. Fabric loopback interface IP address.routerMac. MAC address of the fabric switch used for all interfaces.isEdgeRouter. True if the switch is a leaf, false if it is a spine.SwitchPort. Represents a port on a fabric Switch.switch. Relation to Switch that owns this port.portId. Unique OpenFlow port ID.host_learning. True to enable autodiscovery.PortInterface. Represents an interface on a Port.port. Relation to the SwitchPort that owns this interface.name. The unique name of the fabric switch port.vlanUntagged. Optional untagged VLAN ID for the interface.NodeToSwitchPort. Connects a SwitchPort to a Node.port. SwitchPort that will be connected.node. Node that will be connected.FabricIpAddress. Specifies an IP address attached to a PortInterface.interface. PortInterface that this IP address belongs to.ip. IP Address.description. A short description of this IP address.Here is an example of how to configure a Switch and Ports for OLT and BNG on your fabric. This particular configuration is used in Seba-in-a-Box with an OpenVSwitch software switch, but it should be straightforward to adapt this example to a physical switch.
tosca_definitions_version: tosca_simple_yaml_1_0 imports: - custom_types/switch.yaml - custom_types/switchport.yaml description: Configures the Ponsim SEBA POD with AT&T workflow topology_template: node_templates: # Fabric configuration switch#leaf_1: type: tosca.nodes.Switch properties: driver: ofdpa-ovs # The driver used by the SDN controller ipv4Loopback: 192.168.0.201 # Fabric loopback interface ipv4NodeSid: 17 # The MPLS label used by the switch [17 - 1048576] isEdgeRouter: True # Whether is a leaf (True) or a spine (False) name: leaf_1 ofId: of:0000000000000001 # The unique OpenFlow ID of the fabric switch routerMac: 00:00:02:01:06:01 # MAC address of the fabric switch used for all interfaces # Setup the OLT switch port port#olt_port: type: tosca.nodes.SwitchPort properties: portId: 2 # The unique port OpenFlow port ID host_learning: false # True to enable autodiscovery requirements: - switch: node: switch#leaf_1 relationship: tosca.relationships.BelongsToOne # Port connected to the BNG port#bng_port: type: tosca.nodes.SwitchPort properties: portId: 1 requirements: - switch: node: switch#leaf_1 relationship: tosca.relationships.BelongsToOne
Note: This section is primarily for OpenStack-based compute nodes. It is not necessarily relevant to Kubernetes-based compute nodes at this time.
Compute nodes may be attached to the fabric in order to attach compute-based VNFs to the data plane. The following section assumes the fabric switches have already been setup. The example uses the following nodes:
node1.cord.lab has ip 10.6.1.17 on interface fabricbridge and it is attached to port 17 on the switch leaf1 (and has a route like 10.6.2.0/24 via 10.6.1.254 dev fabricbridge or the default route is pointing to the fabric)node2.cord.lab has ip 10.6.2.18 on interface fabricbridge and it is attached to port 18 on the switch leaf1 (and has a route like 10.6.1.0/24 via 10.6.2.254 dev fabricbridge or the default route is pointing to the fabric)you can use the following TOSCA recipe to:
tosca_definitions_version: tosca_simple_yaml_1_0 description: Set up Fabric service and attach it to ONOS (note that onos-service needs to be loaded) imports: - custom_types/node.yaml - custom_types/nodetoswitchport.yaml - custom_types/switch.yaml - custom_types/switchport.yaml - custom_types/deployment.yaml - custom_types/site.yaml - custom_types/sitedeployment.yaml topology_template: node_templates: # nodes node#node1: type: tosca.nodes.Node properties: dataPlaneIntf: fabricbridge dataPlaneIp: 10.6.1.17/24 name: node1.cord.lab requirements: - site_deployment: node: site_deployment relationship: tosca.relationships.BelongsToOne node#node2: type: tosca.nodes.Node properties: dataPlaneIntf: fabricbridge dataPlaneIp: 10.6.2.18/24 name: node2.cord.lab requirements: - site_deployment: node: site_deployment relationship: tosca.relationships.BelongsToOne # ports (defined in the above recipe) switch#leaf1: type: tosca.nodes.Switch properties: name: leaf1 must-exist: true port#port17: type: tosca.nodes.SwitchPort properties: portId: 17 requirements: - switch: node: switch#leaf1 relationship: tosca.relationships.BelongsToOne port#port18: type: tosca.nodes.SwitchPort properties: portId: 18 requirements: - switch: node: switch#leaf1 relationship: tosca.relationships.BelongsToOne # attaching nodes to ports node1_to_port17: type: tosca.nodes.NodeToSwitchPort requirements: - port: node: port#port17 relationship: tosca.relationships.BelongsToOne - node: node: node#node1 relationship: tosca.relationships.BelongsToOne node2_to_port18: type: tosca.nodes.NodeToSwitchPort requirements: - port: node: port#port18 relationship: tosca.relationships.BelongsToOne - node: node: node#node2 relationship: tosca.relationships.BelongsToOne # extra setup required by XOS (note that this needs to be customized to your installation) mySite: type: tosca.nodes.Site properties: name: mySite login_base: opencord abbreviated_name: ms site_url: http://opencord.org/ hosts_nodes: true myDeployment: type: tosca.nodes.Deployment properties: name: myDeployment site_deployment: type: tosca.nodes.SiteDeployment requirements: - site: node: mySite relationship: tosca.relationships.BelongsToOne - deployment: node: myDeployment relationship: tosca.relationships.BelongsToOne
This will cause the correct fabric configuration to be generated and pushed to the fabric.
The Fabric Service is an infrastructure service that supports other services, and does not provide ServiceInstances of its own. The Fabric Service depends upon the ONOS Service, as Fabric is implemented as an ONOS Application.
When Switch or SwitchPort are created, modified, or deleted, the appropriate REST API calls are performed to ONOS using the /onos/v1/network/configuration/ endpoint.
If an event is received that indicates ONOS has been restarted, then all Switch and SwitchPort objects will be dirtied, causing the state to be resynchronized to ONOS.