tree: 7541106f6e7861236f9778178bd14cdbfd403365 [path history] [tgz]
  1. README.md
docs/README.md

Fabric service

The Fabric service is responsible for configuring the fabric switches in ONOS.

At this point we assume you followed the Fabric setup guide and your physical infrastructure is configured and ready to go.

Models

The fabric service is composed of the following models:

  • FabricService. Global service-related parameters such as the name of the service
    • autoconfig. Determines whether the fabric is automatically configured.
  • Switch. Represents a fabric switch.
    • name. Name of switch.
    • ofId. Openflow ID of switch.
    • driver. Driver used by the SDN controller, defaults to ofdpa3.
    • ipv4NodeSid. MPLS label used by the switch.
    • ipv4Loopback. Fabric loopback interface IP address.
    • routerMac. MAC address of the fabric switch used for all interfaces.
    • isEdgeRouter. True if the switch is a leaf, false if it is a spine.
    • managementAddress. Address where this switch can be managed.
  • SwitchPort. Represents a port on a fabric Switch.
    • switch. Relation to Switch that owns this port.
    • portId. Unique OpenFlow port ID.
    • host_learning. True to enable autodiscovery.
    • admin_state. [enabled | disabled]. Desired administrative state, pushed to device.
    • oper_status. [enabled | disabled]. Operational status, feedback from switch.
    • kind. [access | internet]. Kind of port.
  • PortInterface. Represents an interface on a Port.
    • port. Relation to the SwitchPort that owns this interface.
    • name. The unique name of the fabric switch port.
    • vlanUntagged. Optional untagged VLAN ID for the interface.
  • NodeToSwitchPort. Connects a SwitchPort to a Node.
    • port. SwitchPort that will be connected.
    • node. Node that will be connected.
  • FabricIpAddress. Specifies an IP address attached to a PortInterface.
    • interface. PortInterface that this IP address belongs to.
    • ip. IP Address.
    • description. A short description of this IP address.

Example TOSCA - Configuring Switches and Ports

Here is an example of how to configure a Switch and Ports for OLT and BNG on your fabric. This particular configuration is used in Seba-in-a-Box with an OpenVSwitch software switch, but it should be straightforward to adapt this example to a physical switch.

tosca_definitions_version: tosca_simple_yaml_1_0
imports:
  - custom_types/switch.yaml
  - custom_types/switchport.yaml

description: Configures the Ponsim SEBA POD with AT&T workflow

topology_template:
  node_templates:
    # Fabric configuration
    switch#leaf_1:
      type: tosca.nodes.Switch
      properties:
        driver: ofdpa-ovs # The driver used by the SDN controller
        ipv4Loopback: 192.168.0.201 # Fabric loopback interface
        ipv4NodeSid: 17 # The MPLS label used by the switch [17 - 1048576]
        isEdgeRouter: True # Whether is a leaf (True) or a spine (False)
        name: leaf_1
        ofId: of:0000000000000001 # The unique OpenFlow ID of the fabric switch
        routerMac: 00:00:02:01:06:01 # MAC address of the fabric switch used for all interfaces

    # Setup the OLT switch port
    port#olt_port:
      type: tosca.nodes.SwitchPort
      properties:
        portId: 2 # The unique port OpenFlow port ID
        host_learning: false # True to enable autodiscovery
      requirements:
        - switch:
            node: switch#leaf_1
            relationship: tosca.relationships.BelongsToOne

    # Port connected to the BNG
    port#bng_port:
      type: tosca.nodes.SwitchPort
      properties:
        portId: 1
      requirements:
        - switch:
            node: switch#leaf_1
            relationship: tosca.relationships.BelongsToOne

Example TOSCA - Attaching Compute Nodes

Note: This section is primarily for OpenStack-based compute nodes. It is not necessarily relevant to Kubernetes-based compute nodes at this time.

Compute nodes may be attached to the fabric in order to attach compute-based VNFs to the data plane. The following section assumes the fabric switches have already been setup. The example uses the following nodes:

  • node1.cord.lab has ip 10.6.1.17 on interface fabricbridge and it is attached to port 17 on the switch leaf1 (and has a route like 10.6.2.0/24 via 10.6.1.254 dev fabricbridge or the default route is pointing to the fabric)
  • node2.cord.lab has ip 10.6.2.18 on interface fabricbridge and it is attached to port 18 on the switch leaf1 (and has a route like 10.6.1.0/24 via 10.6.2.254 dev fabricbridge or the default route is pointing to the fabric)

you can use the following TOSCA recipe to:

  • add the Nodes to XOS
  • add the two Ports to the Switch
  • associate each Node to a Port
tosca_definitions_version: tosca_simple_yaml_1_0
description: Set up Fabric service and attach it to ONOS (note that onos-service needs to be loaded)
imports:
  - custom_types/node.yaml
  - custom_types/nodetoswitchport.yaml
  - custom_types/switch.yaml
  - custom_types/switchport.yaml
  - custom_types/site.yaml

topology_template:
  node_templates:

    # nodes
    node#node1:
        type: tosca.nodes.Node
        properties:
            dataPlaneIntf: fabricbridge
            dataPlaneIp: 10.6.1.17/24
            name: node1.cord.lab
        requirements:
            - site:
                node: mySite
                relationship: tosca.relationships.BelongsToOne

    node#node2:
        type: tosca.nodes.Node
        properties:
            dataPlaneIntf: fabricbridge
            dataPlaneIp: 10.6.2.18/24
            name: node2.cord.lab
        requirements:
            - site:
                node: mySite
                relationship: tosca.relationships.BelongsToOne

    # ports (defined in the above recipe)
    switch#leaf1:
      type: tosca.nodes.Switch
      properties:
        name: leaf1
        must-exist: true

    port#port17:
      type: tosca.nodes.SwitchPort
      properties:
        portId: 17
      requirements:
        - switch:
            node: switch#leaf1
            relationship: tosca.relationships.BelongsToOne

    port#port18:
      type: tosca.nodes.SwitchPort
      properties:
        portId: 18
      requirements:
        - switch:
            node: switch#leaf1
            relationship: tosca.relationships.BelongsToOne

    # attaching nodes to ports
    node1_to_port17:
        type: tosca.nodes.NodeToSwitchPort
        requirements:
            - port:
                node: port#port17
                relationship: tosca.relationships.BelongsToOne
            - node:
                node: node#node1
                relationship: tosca.relationships.BelongsToOne

    node2_to_port18:
        type: tosca.nodes.NodeToSwitchPort
        requirements:
            - port:
                node: port#port18
                relationship: tosca.relationships.BelongsToOne
            - node:
                node: node#node2
                relationship: tosca.relationships.BelongsToOne

    # extra setup required by XOS (note that this needs to be customized to your installation)
    mySite:
      type: tosca.nodes.Site
      properties:
          name: mySite
          login_base: opencord
          abbreviated_name: ms
          site_url: http://opencord.org/
          hosts_nodes: true

This will cause the correct fabric configuration to be generated and pushed to the fabric.

Integration with other Services

The Fabric Service is an infrastructure service that supports other services, and does not provide ServiceInstances of its own. The Fabric Service depends upon the ONOS Service, as Fabric is implemented as an ONOS Application.

Synchronization workflow

Switch, SwitchPort

When Switch or SwitchPort are created, modified, or deleted, the appropriate REST API calls are performed to ONOS using the /onos/v1/network/configuration/ endpoint.

Event Steps

If an event is received that indicates ONOS has been restarted, then all Switch and SwitchPort objects will be dirtied, causing the state to be resynchronized to ONOS.

If an event is received from ONOS that indicates port status has changed, then the appropriate Switch and/or SwitchPort objects will be updated.