VOLTHA DEPLOYMENT TOOL

Thie repository describes how to the the voltha script to install a VOLTHA deployment. voltha can be used to deploy an instance into an existing Kubernetes cluster (physical or virtual) or can be start up a local docker-in-docker KinD Kuberentes cluster in which to deploy VOLTHA.

When deploying VOLTHA there are several configuration options tha can be set as described in the CONFIGURATION section below. All configuration options are specified as envirment variables.

PREREQUISITES

The voltha script uses several standard Linux tools to deploy VOLTHA including curl, sed, and jq. This tools must be installed before using the script. The script checks for the presence of these tools before it deployes VOLTHA and will exit with an error if the tools are not present.

NOTE: If you are deploying a KinD Kubernetes cluster using the voltha script, you must also also have Docker installed

INSTALL TYPE

The voltha script can install two variations or types of a VOLTHA deployment: minimal or full. The difference is characterized in the following table:

Throughout this README.md file deployment and configuration files are referenced in the form $TYPE-cluster.cfg and $TYPE-values.yaml. Depending on which type of deloyment you wish to install replace $TYPE with either minimal or full. If you set the environment variable TYPE to the desired deployment type, example below, then the commands can be executed via a simply copy and paste to your command line.

export TYPE=minimal

TL;DR

OK, if you really don't care how it starts and you just want it started. After cloning the repository and making sure you have the prerequisites installed, just execute

DEPLOY_K8S=y WITH_BBSIM=y WITH_RADIUS=y CONFIG_SADIS=y  ./voltha up

and the minimal cluster should start.

To remove voltha use DEPLOY_K8S=y ./voltha down

RUN WITHOUT CLONING REPOSITORY

The voltha script can be run without cloning the complete repository. To do so, download the script and run it.

curl -sSL https://raw.githubusercontent.com/opencord/kind-voltha/master/voltha --output ./voltha
chmod +x ./voltha
DEPLOY_K8S=y WITH_BBSIM=y WITH_RADIUS=y CONFIG_SADIS=y  ./voltha up

NOTE: Shown significantly sped up (20x), actual install was about 8 minutes.

CONFIGURATION

The option should be set using environment variables, thus to start VOLTHA with the BBSIM POD, RADIUS, and ONOS SADIS configured you could use the following command:

WITH_BBSIM=yes WITH_RADIUS=y CONFIG_SADIS=y  voltha up

To start a specific version of VOLTHA, e.g. 2.3, you could use the following commands:

git checkout tags/3.0.3 -b 3.0.3
source releases/voltha-2.3 && voltha up

Please check the releases folder to see the available ones and pick the correct tag associatet do that release.

Custom Namespaces

Separate namespaces can be specified for various components

• VOLTHA_NS (default: voltha) for cores, ofagent, Etcd (yes), Kafka (yes)
• ADAPTER_NS (default: voltha) for device adapters
• INFRA_NS (default: default) for RADIUS, ONOS, Etcd (external), Kafka (external)
• BBSIM_NS (default: voltha) for BBSIM instances

As an example BBSIM_NS=devices deployes BBSim in the devices namespace.

External Kafka, Etcd and ONOS

WITH_ETCD, WITH_KAFKA and WITH_ONOS can have different values depending on the deployment needs:

When specifying the <endpoint> of the service the format for each of these is service-name[:port]. Port is optional and will default to the standard port for the given service. For example, WITH_KAFA=kafka.infra.svc.cluster.local

Specifying the endpoint enable to use ./voltha up incrementally, for example:

DEPLOY_K8S=n WITH_BBSIM=y WITH_RADIUS=no CONFIG_SADIS=no  WITH_ONOS=onos-openflow.infra.svc.cluster.local  WITH_ETCD=etcd-cluster-client.infra.svc.cluster.local WITH_KAFKA=kafka.infra.svc.cluster.local  INFRA_NS=infra BBSIM_NS=devices ADAPTER_NS=adapters ./voltha up

starts VOLTHA with external ONOS,KAFKA,ETCD in the infra namespace.

CONFIG_SADIS Values

Controlling VOLTHA with an ONOS cluster

To provide HA, resilinecy and failover ONOS can be configured in cluster mode. A 3 node ONOS deployment for example can be achieved via the full configuration:

TYPE=full WITH_ONOS=classic NUM_OF_ONOS=3 NUM_OF_ATOMIX=3 ./voltha up

Please note the TYPE=full that deploys a 3 worker nodes for k8s and WITH_ONOS=classic that uses the cluster-enabled helm chart for ONOS (version 2.2). The NUM_OF_ONOS=3 NUM_OF_ATOMIX=3 flags set the number of Atomix nodes and ONOS nodes. As usual one can add as many other options, for example CONFIG_SADIS=y.

GENERATED CONFIGURATION

When the voltha script is run it generates a file that contains the configuration settings. This file will be named $TYPE-env.sh. The user can source this file to set the configuration as well as establish key environment variables in order to access VOLTHA, including:

After voltha up is run, it is useful to source this file.

QUICK CHECK

After source the $TYPE-env.sh file, you should be able to access VOLTHA via the control application voltctl. To validate this you can use the following command

voltctl version

and should see output similar to

Client:
 Version        1.0.14
 Go version:    go1.12.8
 Vcs reference: 086629f0403fe67213fa0df5dc4d7b7ee317cbac
 Vcs dirty:     false
 Built:         2020-03-03T13:48:00Z
 OS/Arch:       linux/amd64

Cluster:
 Version        2.3.3-dev
 Go version:    1.13.8
 Vcs feference: aa8bd4dcc3510caf2c5362106d9bff2852663d31
 Vcs dirty:     false
 Built:         2020-03-06T16:16:47Z
 OS/Arch:       linux/amd64

If you've run the voltha script with WITH_BBSIM=y you can now create a BBSIM OLT with

voltctl device create -t openolt -H bbsim0.voltha.svc:50060

TROUBLESHOOTING

When VOLTHA is installed the install log is written to the file install-$TYPE.log. If the install appears stalled or is not completing consulting this file may indicate the reason.

Similarly, when VOLTHA is uninstalled down-$TYPE.log is written and should be consulted in the event of an error or unexpected result.