diff --git a/generated/reani-g.go b/generated/reani-g.go
new file mode 100644
index 0000000..dce1d9d
--- /dev/null
+++ b/generated/reani-g.go
@@ -0,0 +1,193 @@
+/*
+ * Copyright (c) 2018 - present.  Boling Consulting Solutions (bcsw.net)
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ * http://www.apache.org/licenses/LICENSE-2.0
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+/*
+ * NOTE: This file was generated, manual edits will be overwritten!
+ *
+ * Generated by 'goCodeGenerator.py':
+ *              https://github.com/cboling/OMCI-parser/README.md
+ */
+
+package generated
+
+import "github.com/deckarep/golang-set"
+
+// ReAniGClassID is the 16-bit ID for the OMCI
+// Managed entity RE ANI-G
+const ReAniGClassID ClassID = ClassID(313)
+
+var reanigBME *ManagedEntityDefinition
+
+// ReAniG (class ID #313)
+//	This ME organizes data associated with each R'/S' physical interface of an RE if the RE supports
+//	OEO regeneration in either direction. The management ONU automatically creates one instance of
+//	this ME for each R'/S' physical port (uni- or bidirectional) as follows.
+//
+//	o	When the RE has mid-span PON RE ANI interface ports built into its 	factory configuration.
+//
+//	o	When a cardholder is provisioned to expect a circuit pack of the mid-span PON RE ANI type.
+//
+//	o	When a cardholder provisioned for plug-and-play is equipped with a circuit pack of the midspan
+//	PON RE ANI type. Note that the installation of a plug-and-play card may indicate the presence of
+//	a mid-span PON RE ANI port via equipment ID as well as its type attribute, and indeed may cause
+//	the management ONU to instantiate a port-mapping package to specify the ports precisely.
+//
+//	The management ONU automatically deletes instances of this ME when a cardholder is neither
+//	provisioned to expect a mid-span PON RE ANI circuit pack, nor is it equipped with a mid-span PON
+//	RE ANI circuit pack.
+//
+//	As illustrated in Figure 8.2.10-4, an RE ANI-G may share the physical port with an RE downstream
+//	amplifier. The ONU declares a shared configuration through the port-mapping package combined
+//	port table, whose structure defines one ME as the master. It is recommended that the RE ANI-G be
+//	the master, with the RE downstream amplifier as a secondary ME.
+//
+//	The administrative state, operational state and ARC attributes of the master ME override similar
+//	attributes in secondary MEs associated with the same port. In the secondary ME, these attributes
+//	are present, but cause no action when written and have undefined values when read. The RE
+//	downstream amplifier should use its provisionable downstream alarm thresholds and should declare
+//	downstream alarms as necessary; other isomorphic alarms should be declared by the RE ANI-G. The
+//	test action should be addressed to the master ME.
+//
+//	Relationships
+//		An instance of this ME is associated with each R'/S' physical interface of an RE that includes
+//		OEO regeneration in either direction, and with one or more instances of the PPTP RE UNI. It may
+//		also be associated with an RE downstream amplifier.
+//
+//	Attributes
+//		Managed Entity Id
+//			NOTE 1 - This ME ID may be identical to that of an RE downstream amplifier if it shares the same
+//			physical slot and port.
+//
+//		Administrative State
+//			NOTE 2 - When an RE supports multiple PONs, or protected access to a single PON, its primary
+//			ANI-G cannot be completely shut down, due to a loss of the management communications capability.
+//			Complete blocking of service and removal of power may nevertheless be appropriate for secondary
+//			RE ANI-Gs. Administrative lock suppresses alarms and notifications for an RE ANI-G, be it either
+//			primary or secondary.
+//
+//		Operational State
+//			Operational state: This attribute indicates whether the ME is capable of performing its
+//			function. Valid values are enabled (0) and disabled (1). (R) (optional) (1-byte)
+//
+//		Arc
+//			ARC:	See clause A.1.4.3. (R,-W) (optional) (1-byte)
+//
+//		Arc Interval
+//			ARC interval: See clause A.1.4.3. (R,-W) (optional) (1-byte)
+//
+//		Optical Signal Level
+//			Optical signal level: This attribute reports the current measurement of total downstream optical
+//			power. Its value is a 2s complement integer referred to 1-mW (i.e., dBm), with 0.002-dB
+//			granularity. (R) (optional) (2-bytes)
+//
+//		Lower Optical Threshold
+//			Lower optical threshold: This attribute specifies the optical level that the RE uses to declare
+//			the downstream low received optical power alarm. Valid values are  -127-dBm (coded as 254) to
+//			0-dBm (coded as 0) in 0.5-dB increments. The default value 0xFF selects the RE's internal
+//			policy. (R,-W) (optional) (1-byte)
+//
+//		Upper Optical Threshold
+//			Upper optical threshold: This attribute specifies the optical level that the RE uses to declare
+//			the downstream high received optical power alarm. Valid values are  -127-dBm (coded as 254) to
+//			0-dBm (coded as 0) in 0.5 dB increments. The default value 0xFF selects the RE's internal
+//			policy. (R,-W) (optional) (1-byte)
+//
+//		Transmit Optical Level
+//			Transmit optical level: This attribute reports the current measurement of mean optical launch
+//			power. Its value is a 2s complement integer referred to 1-mW (i.e., dBm), with 0.002-dB
+//			granularity. (R) (optional) (2-bytes)
+//
+//		Lower Transmit Power Threshold
+//			Lower transmit power threshold: This attribute specifies the minimum mean optical launch power
+//			that the RE uses to declare the low transmit optical power alarm. Its value is a 2s-complement
+//			integer referred to 1-mW (i.e., dBm), with 0.5-dB granularity. The default value 0x7F selects
+//			the RE's internal policy. (R,-W) (optional) (1-byte)
+//
+//		Upper Transmit Power Threshold
+//			Upper transmit power threshold: This attribute specifies the maximum mean optical launch power
+//			that the RE uses to declare the high transmit optical power alarm. Its value is a 2s-complement
+//			integer referred to 1-mW (i.e., dBm), with 0.5-dB granularity. The default value 0x7F selects
+//			the RE's internal policy. (R,-W) (optional) (1-byte)
+//
+//		Usage Mode
+//			3	This R'/S' interface is used as the uplink for both the embedded management ONU and one or
+//			more PPTP RE UNI(s) (in a time division fashion).
+//
+//		Target Upstream Frequency
+//			Target upstream frequency: This attribute specifies the frequency of the converted upstream
+//			signal on the optical trunk line (OTL), in gigahertz. The converted frequency must conform to
+//			the frequency plan specified in [ITUT G.984.6]. The value 0 means that the upstream signal
+//			frequency remains the same as the original frequency; no frequency conversion is done. If the RE
+//			does not support provisionable upstream frequency (wavelength), this attribute should take the
+//			fixed value representing the RE's capability and the RE should deny attempts to set the value of
+//			the attribute. If the RE does support provisionable upstream frequency conversion, the default
+//			value of this attribute is 0. (R, W) (optional) (4 bytes).
+//
+//		Target Downstream Frequency
+//			Target downstream frequency: This attribute specifies the frequency of the downstream signal
+//			received by the RE on the OTL, in gigahertz. The incoming frequency must conform to the
+//			frequency plan specified in [ITUT G.984.6]. The default value 0 means that the downstream
+//			frequency remains the same as its original frequency; no frequency conversion is done. If the RE
+//			does not support provisionable downstream frequency selectivity, this attribute should take the
+//			fixed value representing the RE's capability, and the RE should deny attempts to set the value
+//			of the attribute. If the RE does support provisionable downstream frequency selectivity, the
+//			default value of this attribute is 0. (R, W) (optional) (4 bytes).
+//
+//		Upstream Signal Transmission Mode
+//			Upstream signal transmission mode: When true, this Boolean attribute enables conversion from
+//			burst mode to continuous mode. The default value false specifies burst mode upstream
+//			transmission. If the RE does not have the ability to convert from burst to continuous mode
+//			transmission, it should deny attempts to set this attribute to true. (R, W) (optional) (1 byte)
+//
+type ReAniG struct {
+	ManagedEntityDefinition
+	Attributes AttributeValueMap
+}
+
+func init() {
+	reanigBME = &ManagedEntityDefinition{
+		Name:    "ReAniG",
+		ClassID: 313,
+		MessageTypes: mapset.NewSetWith(
+			Get,
+			Set,
+		),
+		AllowedAttributeMask: 0xfffc,
+		AttributeDefinitions: AttributeDefinitionMap{
+			0:  Uint16Field("ManagedEntityId", PointerAttributeType, 0x0000, 0, mapset.NewSetWith(Read), false, false, false, 0),
+			1:  ByteField("AdministrativeState", UnsignedIntegerAttributeType, 0x8000, 0, mapset.NewSetWith(Read, Write), false, false, false, 1),
+			2:  ByteField("OperationalState", UnsignedIntegerAttributeType, 0x4000, 0, mapset.NewSetWith(Read), true, true, false, 2),
+			3:  ByteField("Arc", UnsignedIntegerAttributeType, 0x2000, 0, mapset.NewSetWith(Read, Write), true, true, false, 3),
+			4:  ByteField("ArcInterval", UnsignedIntegerAttributeType, 0x1000, 0, mapset.NewSetWith(Read, Write), false, true, false, 4),
+			5:  Uint16Field("OpticalSignalLevel", UnsignedIntegerAttributeType, 0x0800, 0, mapset.NewSetWith(Read), false, true, false, 5),
+			6:  ByteField("LowerOpticalThreshold", UnsignedIntegerAttributeType, 0x0400, 0, mapset.NewSetWith(Read, Write), false, true, false, 6),
+			7:  ByteField("UpperOpticalThreshold", UnsignedIntegerAttributeType, 0x0200, 0, mapset.NewSetWith(Read, Write), false, true, false, 7),
+			8:  Uint16Field("TransmitOpticalLevel", UnsignedIntegerAttributeType, 0x0100, 0, mapset.NewSetWith(Read), false, true, false, 8),
+			9:  ByteField("LowerTransmitPowerThreshold", UnsignedIntegerAttributeType, 0x0080, 0, mapset.NewSetWith(Read, Write), false, true, false, 9),
+			10: ByteField("UpperTransmitPowerThreshold", UnsignedIntegerAttributeType, 0x0040, 0, mapset.NewSetWith(Read, Write), false, true, false, 10),
+			11: ByteField("UsageMode", UnsignedIntegerAttributeType, 0x0020, 0, mapset.NewSetWith(Read, Write), false, false, false, 11),
+			12: Uint32Field("TargetUpstreamFrequency", UnsignedIntegerAttributeType, 0x0010, 0, mapset.NewSetWith(Read, Write), false, true, false, 12),
+			13: Uint32Field("TargetDownstreamFrequency", UnsignedIntegerAttributeType, 0x0008, 0, mapset.NewSetWith(Read, Write), false, true, false, 13),
+			14: ByteField("UpstreamSignalTransmissionMode", UnsignedIntegerAttributeType, 0x0004, 0, mapset.NewSetWith(Read, Write), false, true, false, 14),
+		},
+		Access:  CreatedByOnu,
+		Support: UnknownSupport,
+	}
+}
+
+// NewReAniG (class ID 313) creates the basic
+// Managed Entity definition that is used to validate an ME of this type that
+// is received from or transmitted to the OMCC.
+func NewReAniG(params ...ParamData) (*ManagedEntity, OmciErrors) {
+	return NewManagedEntity(*reanigBME, params...)
+}