Adapting PODs configurations to the new build system - master
Change-Id: Ifbefa708d67fc8f9ff183bb7b6504b7d5baeec37
diff --git a/qct-pod4.yml b/qct-pod4.yml
index c093b48..8566451 100644
--- a/qct-pod4.yml
+++ b/qct-pod4.yml
@@ -13,67 +13,67 @@
# See the License for the specific language governing permissions and
# limitations under the License.
-
-# Deployment configuration for a physical hardware POD
---
-# this is used to generate the genconfig/cord-inv file
-headnode:
- ip: '10.201.101.41'
- ansible_user: 'cord'
- ansible_ssh_pass: 'cord'
- ansible_ssh_port: 22
+cord_scenario: cord
+cord_profile: rcord
-common:
+vagrant_vms:
+ - 'corddev'
- # set to the profile of cord you want to install
- cord_profile: 'rcord'
+# Variables
+credentials_dir: '/opt/credentials'
+pki_dir: '/opt/pki'
+ssh_pki_dir: '/opt/ssh_pki'
- # cord dir is shared to corddev VM, causing permissions issues if these aren't set
- credentials_dir: '/opt/credentials'
- pki_dir: '/opt/pki'
- ssh_pki_dir: '/opt/ssh_pki'
+fabric_ip: '10.6.1.1/24'
+management_ip: '10.6.0.1/24'
+external_ip: '10.201.101.41/24'
+external_gw: '10.201.101.1'
+external_iface: 'eth2'
+management_network: 10.6.0.0/24
- # all of these are written to genconfig/config.yml, and needs a rework
+deploy_docker_registry: "10.201.101.41:5000"
- # Network address information for the head node:
- #
- # fabric_ip - the IP address and mask bits to be used to configure the network
- # interface connected to the leaf - spine fabric
- #
- # management_ip - the IP address and mask bits to be used to configure the network
- # interface connecting the head node to the POD internal
- # management network. The head node will deliver DHCP addresses to
- # the other compute nodes over this interface
- #
- # external_ip - the IP address and mask bits to be used to configure the network
- # interface connecting the head node (and the POD) to the
- # Internet. All traffic in the POD to external hosts will be
- # NAT-ed through this interface
- fabric_ip: '10.6.1.1/24'
- management_ip: '10.6.0.1/24'
- external_ip: '10.201.101.41/24'
- external_iface: 'eth2'
- external_gw: '10.201.101.1'
- skipTags:
- extraVars:
- - 'management_ignore_names=eth0'
+headnode: cord@10.201.101.41
-passwords:
- compute_node: "ubuntu"
- maas_admin: "admin"
- maas_user: "cord"
+# NOTE: The `host_cord_profile_dir` variable below is the path to the cord_profile dir that
+# gets mounted to corddev VM.This `cord_profile` dir typically lives in a directory
+# one level up from the `cord` directory
+host_cord_profile_dir: "/var/jenkins_home/workspace/cord_profile"
-docker:
- imageVersion: candidate
+build_targets:
+ - 'setup-automation'
-otherNodes:
- # Experimental
- #
- # Specifies the subnet and address range that will be used to allocate IP addresses
- # to the compute nodes as they are deployed into the POD.
- fabric:
- network: 10.6.1.1/24
- range_low: 10.6.1.2
- range_high: 10.6.1.253
+copy_cord_prereqs:
+ - 'config-ssh-key'
+skipTags:
+ - 'set_compute_node_password'
+
+# Wait until headnode prepped before building containers, for consistent DNS
+docker_images_prereqs:
+ - 'prep-headnode'
+
+# node topology
+physical_node_list:
+ - name: head1
+ aliases:
+ - head
+
+management_ignore_names: 'eth0'
+
+# Inventory for ansible, used to generate inventory.ini
+inventory_groups:
+ config:
+ localhost:
+ ansible_connection: local
+ build:
+ corddev:
+ head:
+ head1:
+ ansible_host: 10.201.101.41
+ ansible_port: 22
+ ansible_user: cord
+ ansible_ssh_pass: cord
+ compute: