Adding config files for qct pods 3 and 4
Change-Id: I1ee0e9b18e172f136b3674f68adc6b71f44e6328
diff --git a/qct-pod3.yml b/qct-pod3.yml
new file mode 100644
index 0000000..6f4fab6
--- /dev/null
+++ b/qct-pod3.yml
@@ -0,0 +1,63 @@
+# Deployment configuration for a physical hardware POD
+---
+
+# this is used to generate the genconfig/cord-inv file
+headnode:
+ ip: '10.201.101.31'
+ ansible_user: 'cord'
+ ansible_ssh_pass: 'cord'
+ ansible_ssh_port: 22
+
+common:
+
+ # set to the profile of cord you want to install
+ cord_profile: 'rcord'
+
+ # directories on the head node that the cord dir is copied to, and profile is created in
+ cord_dir: '/opt/cord'
+ cord_profile_dir: '/opt/cord_profile'
+
+
+ # all of these are written to genconfig/config.yml, and needs a rework
+
+ # Network address information for the head node:
+ #
+ # fabric_ip - the IP address and mask bits to be used to configure the network
+ # interface connected to the leaf - spine fabric
+ #
+ # management_ip - the IP address and mask bits to be used to configure the network
+ # interface connecting the head node to the POD internal
+ # management network. The head node will deliver DHCP addresses to
+ # the other compute nodes over this interface
+ #
+ # external_ip - the IP address and mask bits to be used to configure the network
+ # interface connecting the head node (and the POD) to the
+ # Internet. All traffic in the POD to external hosts will be
+ # NAT-ed through this interface
+ fabric_ip: '10.6.1.1/24'
+ management_ip: '10.6.0.1/24'
+ external_ip: '10.201.101.31/24'
+ external_iface: 'eth2'
+ external_gw: '10.201.101.1'
+ skipTags:
+ extraVars:
+ - 'management_ignore_names=eth0'
+
+passwords:
+ compute_node: "ubuntu"
+ maas_admin: "admin"
+ maas_user: "cord"
+
+docker:
+ imageVersion: candidate
+
+otherNodes:
+ # Experimental
+ #
+ # Specifies the subnet and address range that will be used to allocate IP addresses
+ # to the compute nodes as they are deployed into the POD.
+ fabric:
+ network: 10.6.1.1/24
+ range_low: 10.6.1.2
+ range_high: 10.6.1.253
+
diff --git a/qct-pod4.yml b/qct-pod4.yml
new file mode 100644
index 0000000..ff4c390
--- /dev/null
+++ b/qct-pod4.yml
@@ -0,0 +1,63 @@
+# Deployment configuration for a physical hardware POD
+---
+
+# this is used to generate the genconfig/cord-inv file
+headnode:
+ ip: '10.201.101.41'
+ ansible_user: 'cord'
+ ansible_ssh_pass: 'cord'
+ ansible_ssh_port: 22
+
+common:
+
+ # set to the profile of cord you want to install
+ cord_profile: 'rcord'
+
+ # directories on the head node that the cord dir is copied to, and profile is created in
+ cord_dir: '/opt/cord'
+ cord_profile_dir: '/opt/cord_profile'
+
+
+ # all of these are written to genconfig/config.yml, and needs a rework
+
+ # Network address information for the head node:
+ #
+ # fabric_ip - the IP address and mask bits to be used to configure the network
+ # interface connected to the leaf - spine fabric
+ #
+ # management_ip - the IP address and mask bits to be used to configure the network
+ # interface connecting the head node to the POD internal
+ # management network. The head node will deliver DHCP addresses to
+ # the other compute nodes over this interface
+ #
+ # external_ip - the IP address and mask bits to be used to configure the network
+ # interface connecting the head node (and the POD) to the
+ # Internet. All traffic in the POD to external hosts will be
+ # NAT-ed through this interface
+ fabric_ip: '10.6.1.1/24'
+ management_ip: '10.6.0.1/24'
+ external_ip: '10.201.101.41/24'
+ external_iface: 'eth2'
+ external_gw: '10.201.101.1'
+ skipTags:
+ extraVars:
+ - 'management_ignore_names=eth0'
+
+passwords:
+ compute_node: "ubuntu"
+ maas_admin: "admin"
+ maas_user: "cord"
+
+docker:
+ imageVersion: candidate
+
+otherNodes:
+ # Experimental
+ #
+ # Specifies the subnet and address range that will be used to allocate IP addresses
+ # to the compute nodes as they are deployed into the POD.
+ fabric:
+ network: 10.6.1.1/24
+ range_low: 10.6.1.2
+ range_high: 10.6.1.253
+