2004-11-06 Paul Jakma <paul@dishone.st>
* defines.texi.in: New file, texi variables should be set here,
autoconf substitution is available. Define common AUTHORS,
COPYRIGHT_YEAR and COPYRIGHT_STR vars.
* (global): Make use of makeinfo node pointer auto-creation
to avoid having to fully specify links for nodes, so we only have
to specify current node name - simplifies text slightly.
Remove extraneous newlines which appear to cause extra blank pages
to be added in output.
Update copyright strings which appear in various places to
use the new COPYRIGHT_STR texinfo variable.
Change url to uref, the former need not output an actual
hyperlink depending on version of texinfo, the latter should if
supported by the format (eg PDF).
* texinfo.tex: Update to a more recent version. previous file
was many many years old. This file should possibly be removed
altogether, and allowed to be installed by automake.
* quagga.texi: Make use of automake's version.texi feature to
have VERSION and some other vars auto-defined. include
defines.texi. Change copyright strings to use the COPYRIGHT_STR
variable.
* install.texi: Make the privs section an actual section. Ditto for
the Linux notes.
* overview.texi: Supply URL for Quagga, where format allows. Tidy up
one or two paragraphs slightly.
Update the section on supported platforms.
Remove the ZNOG list stuff, direct reader to the website for
further information on email lists.
* vtysh.texi: Update the integrated config file section. Make the
commands sections so correct PDF indexes are built.
diff --git a/doc/ospfd.texi b/doc/ospfd.texi
index aa66ce1..789e9bf 100644
--- a/doc/ospfd.texi
+++ b/doc/ospfd.texi
@@ -1,5 +1,4 @@
-@node OSPFv2, OSPFv3, RIPng, Top
-@comment node-name, next, previous, up
+@node OSPFv2
@chapter OSPFv2
OSPF version 2 is a routing protocol which described in
@@ -18,8 +17,7 @@
* Debugging OSPF::
@end menu
-@node Configuring ospfd, OSPF router, OSPFv2, OSPFv2
-@comment node-name, next, previous, up
+@node Configuring ospfd
@section Configuring ospfd
There is no @command{ospfd} specific options. Common options can be
@@ -31,8 +29,7 @@
Like other daemons, @command{ospfd} configuration is done in OSPF
specific configuration file @file{ospfd.conf}.
-@node OSPF router, OSPF area, Configuring ospfd, OSPFv2
-@comment node-name, next, previous, up
+@node OSPF router
@section OSPF router
To start OSPF process you have to specify the OSPF router. As of this
@@ -112,8 +109,7 @@
address 192.168.1.129/25.
@end deffn
-@node OSPF area, OSPF interface, OSPF router, OSPFv2
-@comment node-name, next, previous, up
+@node OSPF area
@section OSPF area
@deffn {OSPF Command} {area @var{a.b.c.d} range @var{a.b.c.d/m}} {}
@@ -244,8 +240,7 @@
@deffnx {OSPF Command} {area <0-4294967295> authentication message-digest} {}
@end deffn
-@node OSPF interface, Redistribute routes to OSPF, OSPF area, OSPFv2
-@comment node-name, next, previous, up
+@node OSPF interface
@section OSPF interface
@deffn {Interface Command} {ip ospf authentication-key AUTH_KEY} {}
@@ -318,8 +313,7 @@
The default value is 1 seconds.
@end deffn
-@node Redistribute routes to OSPF, Showing OSPF information, OSPF interface, OSPFv2
-@comment node-name, next, previous, up
+@node Redistribute routes to OSPF
@section Redistribute routes to OSPF
@deffn {OSPF Command} {redistribute (kernel|connected|static|rip|bgp)} {}
@@ -364,8 +358,7 @@
@deffnx {Command} {no router zebra} {}
@end deffn
-@node Showing OSPF information, Debugging OSPF, Redistribute routes to OSPF, OSPFv2
-@comment node-name, next, previous, up
+@node Showing OSPF information
@section Showing OSPF information
@deffn {Command} {show ip ospf} {}
@@ -403,8 +396,7 @@
@deffn {Command} {show ip ospf route} {}
@end deffn
-@node Debugging OSPF, , Showing OSPF information, OSPFv2
-@comment node-name, next, previous, up
+@node Debugging OSPF
@section Debugging OSPF
@deffn {Command} {debug ospf packet (hello|dd|ls-request|ls-update|ls-ack|all) (send|recv) [detail]} {}