OSPFV3-MIB DEFINITIONS ::= BEGIN 
 
IMPORTS 
        MODULE-IDENTITY, OBJECT-TYPE, mib-2, experimental,
        Counter32, Gauge32, Integer32, IpAddress, 
        Unsigned32 
                FROM SNMPv2-SMI 
        TEXTUAL-CONVENTION, TruthValue, StorageType, RowStatus 
                FROM SNMPv2-TC 
        MODULE-COMPLIANCE, OBJECT-GROUP 
                FROM SNMPv2-CONF 
        InterfaceIndex 
                FROM IF-MIB 
        InetAddressType, InetAddress, InetAddressPrefixLength 
                FROM INET-ADDRESS-MIB 
        AreaID, RouterID, Metric, BigMetric, Status,  
        HelloRange, DesignatedRouterPriority 
                FROM OSPF-MIB; 

ospfv3MIB MODULE-IDENTITY 
        LAST-UPDATED "200404081200Z" 
        ORGANIZATION "IETF OSPF Working Group" 
        CONTACT-INFO 
            "WG E-Mail: ospf@peach.ease.lsoft.com 
             WG Chairs: John.Moy@sycamorenet.com   
                        acee@redback.com 
                        rohit@xebeo.com 
 
             Dan Joyal 
             Nortel Networks 
             600 Technology Park Drive 
             Billerica, MA  01821, USA 
             djoyal@nortelnetworks.com 
 
             Vishwas Manral 
             SiNett Corporation 
             2/1, First Floor 
             Embassy Icon Annex 
             Infantry Road 
             Bangalore 560001 
             vishwas@sinett.com" 
 
         DESCRIPTION 
             "The MIB module to describe OSPF version 3" 
         REVISION "200404081200Z" 
         DESCRIPTION -- RFC Editor assigns RFC xxxx 
             "Initial version, published as RFC xxxx" 
         ::= { experimental 102 } -- IANA assigns xx 
 
-- Texual conventions 
 
UpToRefreshInterval ::= TEXTUAL-CONVENTION 
         STATUS        current 
         DESCRIPTION 
            "The values one might be able to configure for                  
            variables bounded by the Refresh Interval" 
         SYNTAX        Integer32 (1..1800) 
 
RouterDeadRange ::= TEXTUAL-CONVENTION 
         STATUS        current 
         DESCRIPTION 
            "The range of intervals in seconds that a routers hello 
            must have not been seen before a neighbor declares the 
            router down" 
         SYNTAX        Integer32 (1..'FFFF'h) 

 
-- Top-level structure of MIB 
ospfv3Objects        OBJECT IDENTIFIER ::= { ospfv3MIB 1 } 
ospfv3Conformance    OBJECT IDENTIFIER ::= { ospfv3MIB 2 } 
 
-- OSPFv3 General Variables 
 
-- These parameters apply globally to the Router's 
-- OSPFv3 Process. 
 
ospfv3GeneralGroup OBJECT IDENTIFIER ::= { ospfv3Objects 1 } 
 
ospfv3RouterId OBJECT-TYPE 
        SYNTAX         RouterID 
        MAX-ACCESS     read-write 
        STATUS         current 
        DESCRIPTION 
            "A  32-bit  integer  uniquely  identifying  the 
            router in the Autonomous System. 
            To  ensure  uniqueness, this may 
            default  to  the  value  of  one of the 
            router's IPv4 interface addresses if IPv4 is 
            configured on the router." 
        ::= { ospfv3GeneralGroup 1 } 
 
ospfv3AdminStat OBJECT-TYPE 
        SYNTAX          Status 
        MAX-ACCESS      read-write 
        STATUS          current 
        DESCRIPTION 
            "The  administrative  status  of  OSPFv3  in  the 
            router.   The  value 'enabled' denotes that the 
            OSPFv3 Process is active on at least  one  inter- 
            face;  'disabled'  disables  it  on  all inter- 
            faces." 
        ::= { ospfv3GeneralGroup 2 } 
 
ospfv3VersionNumber OBJECT-TYPE 
        SYNTAX          INTEGER { version3(3) } 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The version number of OSPF for IPv6 is 3." 
        ::= { ospfv3GeneralGroup 3 } 
 
ospfv3AreaBdrRtrStatus OBJECT-TYPE 
        SYNTAX          TruthValue 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "A flag to note whether this router is an  area 
            border router." 
        REFERENCE 
            "OSPF Version 2, Section 3 Splitting the AS into 
            Areas" 
        ::= { ospfv3GeneralGroup 4 } 
 
ospfv3ASBdrRtrStatus OBJECT-TYPE 
        SYNTAX          TruthValue 
        MAX-ACCESS      read-write 
        STATUS          current 
        DESCRIPTION 
            "A flag to note whether this router is  config- 
            ured as an Autonomous System border router." 
        REFERENCE 
            "OSPF Version 2, Section 3.3  Classification  of 
            routers" 
        ::= { ospfv3GeneralGroup 5 } 
 
ospfv3AsScopeLsaCount OBJECT-TYPE 
        SYNTAX          Gauge32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The number of AS-Scope (e.g. AS-External) link-state 
            advertisements in the link-state database." 
        ::= { ospfv3GeneralGroup 6 } 
 
ospfv3AsScopeLsaCksumSum OBJECT-TYPE 
        SYNTAX          Integer32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The 32-bit unsigned sum of the LS checksums of 
            the  AS-scoped link-state advertisements  con- 
            tained in the link-state database. This sum 
            can  be  used  to determine if there has been a 
            change in a router's link state  database,  and 
            to  compare  the  link-state  database  of  two 
            routers." 
        ::= { ospfv3GeneralGroup 7 } 
 
ospfv3OriginateNewLsas OBJECT-TYPE 
        SYNTAX          Counter32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The number of  new  link-state  advertisements 
            that  have been originated.  This number is in- 
            cremented each time the router originates a new 
            LSA." 
        ::= { ospfv3GeneralGroup 8 } 
 
ospfv3RxNewLsas OBJECT-TYPE 
        SYNTAX          Counter32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The number of  link-state  advertisements  re- 
            ceived  determined  to  be  new instantiations. 
            This number does not include  newer  instantia- 
            tions  of self-originated link-state advertise- 
            ments." 
        ::= { ospfv3GeneralGroup 9 } 
 
ospfv3ExtLsaCount OBJECT-TYPE 
        SYNTAX          Gauge32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The number of External(LS type 0x4005) in the link-
            state database" 
        ::= { ospfv3GeneralGroup 10 } 
 
 
ospfv3ExtAreaLsdbLimit OBJECT-TYPE 
        SYNTAX          Integer32 (-1..'7FFFFFFF'h) 
        MAX-ACCESS      read-write 
        STATUS          current 
        DESCRIPTION 
            "The  maximum   number   of   non-default   AS- 
            external-LSAs entries that can be stored in the 
            link-state database.  If the value is -1, then 
            there is no limit. 
 
            When the number of non-default AS-external-LSAs 
            in   a  router's  link-state  database  reaches 
            ospfv3ExtAreaLsdbLimit, the router  enters  Overflow- 
            State.   The   router  never  holds  more  than 
            ospfv3ExtAreaLsdbLimit  non-default  AS-external-LSAs 
            in  its  database. OspfExtAreaLsdbLimit MUST be set 
            identically in all routers attached to the OSPFv3 
            backbone  and/or  any regular OSPFv3 area. (i.e., 
            OSPFv3 stub areas and NSSAs are excluded)." 
        ::= { ospfv3GeneralGroup 11 } 
 
ospfv3MulticastExtensions OBJECT-TYPE 
        SYNTAX          BITS { 
                                 intraAreaMulticast(0), 
                                 interAreaMulticast(1), 
                                 interAsMulticast(2) 
                             } 
                                     
        MAX-ACCESS      read-write 
        STATUS          current 
        DESCRIPTION 
            "A Bit Mask indicating whether the router is 
            forwarding IPv6 multicast datagrams 
            based on the algorithms defined in the  Multi- 
            cast Extensions to OSPF. 
 
            If intraAreaMulticast set, indicates that the router 
            can forward  IPv6 multicast datagrams in the router's 
            directly attached areas (called intra-area mul- 
            ticast routing). 
 
            If interAreaMulticast set, indicates that the router 
            can forward IPv6 multicast datagrams between OSPFv3 
            areas (called inter-area multicast routing). 
 
            If interAsMulticast set, indicates that the router can 
            forward  IPv6  multicast datagrams between Auto- 
            nomous Systems (called inter-AS multicast rout- 
            ing). 
 
            Only certain combinations of bit settings are 
            allowed, namely: 
                    - All bits cleared (no multicasting) 
                    - intraAreaMulticast only, 
                    - intraAreaMulticast and interAreaMulticast, 
                    - intraAreaMulticast and interAsMulticast 
                    - intraAreaMulticast, interAreaMulticast and 
                            interAsMulticast 
            By default, all bits are cleared." 
        ::= { ospfv3GeneralGroup 12 } 
 
ospfv3ExitOverflowInterval OBJECT-TYPE 
        SYNTAX          Unsigned32 
        UNITS           "seconds" 
        MAX-ACCESS      read-write 
        STATUS          current 
        DESCRIPTION 
            "The number of  seconds  that,  after  entering 
            OverflowState,  a  router will attempt to leave 
            OverflowState. This allows the router to  again 
            originate  non-default  AS-External-LSAs.  When 
            set to 0, the router will not  leave  Overflow- 
            State until restarted." 
        ::= { ospfv3GeneralGroup 13 } 
 
ospfv3DemandExtensions OBJECT-TYPE 
        SYNTAX         TruthValue 
        MAX-ACCESS     read-write 
        STATUS         current 
        DESCRIPTION 
            "The router's support for demand routing." 
        REFERENCE 
            "OSPF Version 2, Appendix on Demand Routing" 
        ::= { ospfv3GeneralGroup 14 } 
 
ospfv3TrafficEngineeringSupport OBJECT-TYPE 
        SYNTAX          TruthValue 
        MAX-ACCESS      read-write 
        STATUS          current 
        DESCRIPTION 
            "The router's support for traffic engineering 
            extensions." 
        ::= { ospfv3GeneralGroup 15 } 
 
ospfv3ReferenceBandwidth OBJECT-TYPE  
       SYNTAX       Unsigned32  
       MAX-ACCESS   read-write  
       STATUS       current  
       DESCRIPTION  
          "Reference bandwidth in kilobits/second for  
          calculating default interface metrics. The  
          default value is 100,000 KBPS (100 MBPS)"  
    ::= { ospfv3GeneralGroup 16 } 
 
ospfv3RestartSupport OBJECT-TYPE  
       SYNTAX       INTEGER { none (1),  
                              plannedOnly (2),  
                              plannedAndUnplanned (3)  
                         } 
       MAX-ACCESS   read-write  
       STATUS       current  
       DESCRIPTION  
          "The router's support for OSPF hitless restart.  
          Options include: no restart support, only planned  
          restarts or both planned and unplanned restarts."  
       ::= { ospfv3GeneralGroup 17 }  
    
ospfv3RestartInterval OBJECT-TYPE  
       SYNTAX       UpToRefreshInterval 
       UNITS        "seconds"  
       MAX-ACCESS   read-write  
       STATUS       current  
       DESCRIPTION  
          "Configured OSPF hitless restart timeout interval."  
       ::= { ospfv3GeneralGroup 18 }  
    
ospfv3RestartStatus OBJECT-TYPE  
       SYNTAX       INTEGER { notRestarting (1),  
                              plannedRestart (2),  
                              unplannedRestart (3)  
                            }  
       MAX-ACCESS   read-only  
       STATUS       current  
       DESCRIPTION  
          "Current status of OSPF hitless restart."  
       ::= { ospfv3GeneralGroup 19 }  
    
ospfv3RestartAge OBJECT-TYPE  
       SYNTAX       UpToRefreshInterval 
       UNITS        "seconds"  
       MAX-ACCESS   read-only  
       STATUS       current  
       DESCRIPTION  
          "Remaining time in current OSPF hitless restart  
          interval."  
       ::= { ospfv3GeneralGroup 20 }  
    
ospfv3RestartExitReason OBJECT-TYPE  
       SYNTAX       INTEGER { none (1),           -- none attempted  
                              inProgress (2),     -- restart in  
                                                  -- progress  
                              completed (3),      -- successfully  
                                                  -- completed  
                              timedOut (4),       -- timed out  
                              topologyChanged (5) -- aborted due to  
                                                  -- topologychange.  
                            }  
       MAX-ACCESS   read-only  
       STATUS       current  
       DESCRIPTION  
          "Describes the outcome of the last attempt at a  
          hitless restart. If the value is 'none', no restart  
           has yet been attempted. If the value is 'inProgress',  
          a restart attempt is currently underway."  
    ::= { ospfv3GeneralGroup 21 } 
 
 
-- The OSPFv3 Area Data Structure contains information 
-- regarding the various areas. The interfaces and 
-- virtual links are configured as part of these areas. 
-- Area 0.0.0.0, by definition, is the Backbone Area 
 
ospfv3AreaTable OBJECT-TYPE 
        SYNTAX          SEQUENCE OF Ospfv3AreaEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "Information describing the configured  parame- 
            ters  and cumulative statistics of the router's 
            attached areas." 
        REFERENCE 
            "OSPF Version 2, Section 6 The Area Data Struc- 
            ture" 
        ::= { ospfv3Objects 2 } 
 
ospfv3AreaEntry OBJECT-TYPE 
        SYNTAX          Ospfv3AreaEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "Information describing the configured parame- 
            ters and cumulative statistics of one of the 
            router's attached areas." 
        INDEX           { ospfv3AreaId } 
        ::= { ospfv3AreaTable 1 } 
 
Ospfv3AreaEntry ::= SEQUENCE { 
        ospfv3AreaId 
                AreaID, 
        ospfv3ImportAsExtern 
                INTEGER, 
        ospfv3AreaSpfRuns 
                Counter32, 
        ospfv3AreaBdrRtrCount 
                Gauge32, 
        ospfv3AreaAsBdrRtrCount 
                Gauge32, 
        ospfv3AreaScopeLsaCount 
                Gauge32, 
        ospfv3AreaScopeLsaCksumSum 
                Integer32, 
        ospfv3AreaSummary 
                INTEGER, 
        ospfv3AreaStatus 
                RowStatus, 
        ospfv3StubMetric 
                BigMetric, 
        ospfv3AreaNssaTranslatorRole 
                INTEGER, 
        ospfv3AreaNssaTranslatorState 
                INTEGER, 
        ospfv3AreaNssaTranslatorStabilityInterval 
                Unsigned32, 
        ospfv3AreaNssaTranslatorEvents 
                Counter32, 
        ospfv3AreaStubMetricType 
                INTEGER 
        } 
 
ospfv3AreaId OBJECT-TYPE 
        SYNTAX          AreaID 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "A 32-bit integer uniquely identifying an area. 
            Area ID 0.0.0.0 is used for the OSPFv3 backbone." 
        REFERENCE 
            "OSPF Version 2, Appendix C.2 Area parameters" 
        ::= { ospfv3AreaEntry 1 } 
 
ospfv3ImportAsExtern OBJECT-TYPE 
        SYNTAX          INTEGER { 
                        importExternal(1),   -- normal area 
                        importNoExternal(2), -- stub area 
                        importNssa(3)        -- not-so-stubby-area 
                        } 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "Indicates whether an area is a Stub area, NSSA, or 
            standard area. AS-scope LSAs are not imported into Stub 
            Areas or NSSAs. NSSAs import AS-External data as Type-7 
            LSAs which have Area-scope" 
        REFERENCE 
            "OSPF Version 2, Appendix C.2 Area parameters" 
        DEFVAL { importExternal } 
        ::= { ospfv3AreaEntry 2 } 
 
ospfv3AreaSpfRuns OBJECT-TYPE 
        SYNTAX          Counter32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The number of times that the intra-area  route 
            table  has  been  calculated  using this area's 
            link-state database.  This  is  typically  done 
            using Dijkstra's algorithm." 
        ::= { ospfv3AreaEntry 3 } 
 
ospfv3AreaBdrRtrCount OBJECT-TYPE 
        SYNTAX          Gauge32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The total number of area border routers reach- 
            able within this area.  This is initially zero, 
            and is calculated in each SPF Pass." 
        ::= { ospfv3AreaEntry 4 } 
 
ospfv3AreaAsBdrRtrCount OBJECT-TYPE 
        SYNTAX          Gauge32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The total number of Autonomous  System  border 
            routers  reachable  within  this area.  This is 
            initially zero, and is calculated in  each  SPF 
            Pass." 
        ::= { ospfv3AreaEntry 5 } 
 
ospfv3AreaScopeLsaCount OBJECT-TYPE 
        SYNTAX          Gauge32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The total number of Area-Scope link-state  
            advertisements in  this  area's link-state  
            database." 
        ::= { ospfv3AreaEntry 6 } 
 
ospfv3AreaScopeLsaCksumSum OBJECT-TYPE 
        SYNTAX          Integer32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The 32-bit unsigned sum of the Area-Scope link-state 
            advertisements'  LS  checksums  contained in this 
            area's link-state database.  The sum can be used 
            to determine if  there  has been  a  change  in a 
            router's link state database, and to compare the 
            link-state database of two routers." 
        ::= { ospfv3AreaEntry 7 } 
 
ospfv3AreaSummary OBJECT-TYPE 
        SYNTAX          INTEGER { 
                        noAreaSummary(1), 
                        sendAreaSummary(2) 
                        } 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The variable ospfv3AreaSummary controls the  im- 
            port  of  Inter-Area LSAs into stub areas.  It has 
            no effect on other areas. 
 
            If it is noAreaSummary, the router will neither 
            originate  nor  propagate Inter-Area LSAs into the 
            stub area.  It will rely entirely  on  its  de- 
            fault route. 
 
            If it is sendAreaSummary, the router will  both 
            summarize and propagate Inter-Area LSAs." 
        DEFVAL   { sendAreaSummary } 
        ::= { ospfv3AreaEntry 8 } 
 
ospfv3AreaStatus OBJECT-TYPE 
        SYNTAX          RowStatus 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "This variable controls the status of  the  en- 
            try. The use of RowStatus is covered in more detail 
            in [6]." 
        ::= { ospfv3AreaEntry 9 } 
 
ospfv3StubMetric OBJECT-TYPE 
        SYNTAX          BigMetric 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The metric value advertised for the default route 
             into Stub and NSSA areas." 
        ::= { ospfv3AreaEntry 10 } 
 
ospfv3AreaNssaTranslatorRole OBJECT-TYPE 
        SYNTAX          INTEGER { always(1), candidate(2) } 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "Indicates an NSSA Border router's ability to 
            perform NSSA translation of type-7 LSAs into 
            type-5 LSAs." 
        DEFVAL { candidate } 
        ::= { ospfv3AreaEntry 11 } 
 
ospfv3AreaNssaTranslatorState OBJECT-TYPE 
        SYNTAX          INTEGER { 
                        enabled(1), 
                        elected(2), 
                        disabled(3) 
                        } 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "Indicates if and how an NSSA Border router is 
             performing NSSA translation of type-7 LSAs into type-5 
             LSAs. When this object is set to enabled, the NSSA 
             Border router's ospfv3AreaNssTranslatorRole 
             has been set to always. When this object is set to 
             elected, a candidate NSSA Border router is translating 
             type-7 LSAs into type-5. When this object is set to 
             disabled, a candidate NSSA Border router is NOT 
             translating type-7 LSAs into type-5." 
        ::= { ospfv3AreaEntry 12 } 
 
ospfv3AreaNssaTranslatorStabilityInterval OBJECT-TYPE 
        SYNTAX          Unsigned32 
        UNITS           "seconds" 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The number of seconds after an elected translator 
            determines its services are no longer required, that 
            it should continue to perform its translation duties." 
        DEFVAL { 40 } 
        ::= { ospfv3AreaEntry 13 } 
 
ospfv3AreaNssaTranslatorEvents OBJECT-TYPE 
        SYNTAX          Counter32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "Indicates the number of Translator State changes 
            that have occurred since the last boot-up." 
        ::= { ospfv3AreaEntry 14 } 

ospfv3AreaStubMetricType OBJECT-TYPE 
        SYNTAX       INTEGER { 
                        ospfv3Metric (1),  -- OSPF Metric 
                        comparableCost (2), -- external type 1 
                        nonComparable  (3) -- external type 2 
                        } 
        MAX-ACCESS   read-create 
        STATUS       current 
        DESCRIPTION 
           "This variable displays the type of metric ad- 
           vertised as a default route." 
        DEFVAL { ospfv3Metric } 
        ::= { ospfv3AreaEntry 15 } 

-- OSPFv3 AS-Scope Link State Database 
 
-- The Link State Database contains the AS-Scope Link State 
-- Advertisements from throughout the areas that the 
-- device is attached to. 
 
ospfv3AsLsdbTable OBJECT-TYPE 
        SYNTAX          SEQUENCE OF Ospfv3AsLsdbEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "The OSPFv3 Process's AS-Scope Link State Database." 
        ::= { ospfv3Objects 3 } 
 
ospfv3AsLsdbEntry OBJECT-TYPE 
        SYNTAX          Ospfv3AsLsdbEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "A single AS-Scope Link State Advertisement." 
        INDEX           { ospfv3AsLsdbType, 
                          ospfv3AsLsdbRouterId, 
                          ospfv3AsLsdbLsid } 
        ::= { ospfv3AsLsdbTable 1 } 
 
Ospfv3AsLsdbEntry ::= SEQUENCE { 
        ospfv3AsLsdbType 
                Unsigned32, 
        ospfv3AsLsdbRouterId 
                RouterID, 
        ospfv3AsLsdbLsid 
                IpAddress, 
        ospfv3AsLsdbSequence 
                Integer32, 
        ospfv3AsLsdbAge 
                Integer32, 
        ospfv3AsLsdbChecksum 
                Integer32, 
        ospfv3AsLsdbAdvertisement 
                OCTET STRING, 
        ospfv3AsLsdbTypeKnown 
                TruthValue 
        } 
 
ospfv3AsLsdbType OBJECT-TYPE 
        SYNTAX          Unsigned32 (0..4294967295)
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The type of the link state advertisement. 
            Each link state type has a separate advertise- 
            ment format. AS-Scope LSAs not recognized by 
            the router may be stored in the database." 
        ::= { ospfv3AsLsdbEntry 1 } 
 
ospfv3AsLsdbRouterId OBJECT-TYPE 
        SYNTAX          RouterID 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The 32 bit number that uniquely identifies the 
            originating router in the Autonomous System." 
        REFERENCE 
            "OSPF Version 2, Appendix C.1 Global parameters" 
        ::= { ospfv3AsLsdbEntry 2 } 
 
ospfv3AsLsdbLsid OBJECT-TYPE 
        SYNTAX          IpAddress 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The Link State ID is an LS Type Specific field 
            containing a unique identifier; 
            it identifies the piece of the  routing  domain 
            that is being described by the advertisement. 
            In contrast to OSPFv2, the LSID has no 
            addressing semantics." 
        ::= { ospfv3AsLsdbEntry 3 } 
 
-- Note that the OSPF Sequence Number is a 32 bit signed 
-- integer.  It starts with the value '80000001'h, 
-- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h 
-- Thus, a typical sequence number will be very negative. 
 
ospfv3AsLsdbSequence OBJECT-TYPE 
        SYNTAX          Integer32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The sequence number field is a  signed  32-bit 
            integer.   It  is used to detect old and dupli- 
            cate link state advertisements.  The  space  of 
            sequence  numbers  is  linearly  ordered.   The 
            larger the sequence number the more recent  the 
            advertisement." 
        REFERENCE 
            "OSPF Version  2,  Section  12.1.6  LS  sequence 
            number" 
        ::= { ospfv3AsLsdbEntry 4 } 
 
ospfv3AsLsdbAge OBJECT-TYPE 
        SYNTAX          Integer32 -- Should be 0..MaxAge 
                                  -- unless DoNotAge bit is set 
        UNITS           "seconds" 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "This field is the age of the link state adver- 
            tisement in seconds." 
        REFERENCE 
            "OSPF Version 2, Section 12.1.1 LS age" 
        ::= { ospfv3AsLsdbEntry 5 } 
 
ospfv3AsLsdbChecksum OBJECT-TYPE 
        SYNTAX          Integer32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "This field is the  checksum  of  the  complete 
            contents  of  the  advertisement, excepting the 
            age field.  The age field is excepted  so  that 
            an   advertisement's  age  can  be  incremented 
            without updating the  checksum.   The  checksum 
            used  is  the same that is used for ISO connec- 
            tionless datagrams; it is commonly referred  to 
            as the Fletcher checksum." 
        REFERENCE 
            "OSPF Version 2, Section 12.1.7 LS checksum" 
        ::= { ospfv3AsLsdbEntry 6 } 
 
ospfv3AsLsdbAdvertisement OBJECT-TYPE 
        SYNTAX          OCTET STRING (SIZE (1..65535)) 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The entire Link State Advertisement, including 
            its header." 
        ::= { ospfv3AsLsdbEntry 7 } 
 
ospfv3AsLsdbTypeKnown OBJECT-TYPE 
        SYNTAX          TruthValue 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "Is the LSA type recognized by this Router?" 
        ::= { ospfv3AsLsdbEntry 8 } 
 
 
-- OSPFv3 Area-Scope Link State Database 
 
-- The Link State Database contains the Area-Scope Link State 
-- Advertisements from throughout the area that the 
-- device is attached to. 
 
ospfv3AreaLsdbTable OBJECT-TYPE 
        SYNTAX          SEQUENCE OF Ospfv3AreaLsdbEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "The OSPFv3 Process's Area-Scope Link State Database." 
        ::= { ospfv3Objects 4 } 
 
ospfv3AreaLsdbEntry OBJECT-TYPE 
        SYNTAX          Ospfv3AreaLsdbEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "A single Area-Scope Link State Advertisement." 
        INDEX           { ospfv3AreaLsdbAreaId, 
                          ospfv3AreaLsdbType, 
                          ospfv3AreaLsdbRouterId, 
                          ospfv3AreaLsdbLsid } 
        ::= { ospfv3AreaLsdbTable 1 } 
 
Ospfv3AreaLsdbEntry ::= SEQUENCE { 
        ospfv3AreaLsdbAreaId 
                AreaID, 
        ospfv3AreaLsdbType 
                Unsigned32, 
        ospfv3AreaLsdbRouterId 
                RouterID, 
        ospfv3AreaLsdbLsid 
                IpAddress, 
        ospfv3AreaLsdbSequence 
                Integer32, 
        ospfv3AreaLsdbAge 
                Integer32, 
        ospfv3AreaLsdbChecksum 
                Integer32, 
        ospfv3AreaLsdbAdvertisement 
                OCTET STRING, 
        ospfv3AreaLsdbTypeKnown 
                TruthValue 
        } 
 
ospfv3AreaLsdbAreaId OBJECT-TYPE 
        SYNTAX          AreaID 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The 32 bit identifier of the Area from which the 
            LSA was received." 
        REFERENCE 
            "OSPF Version 2, Appendix C.2 Area parameters" 
        ::= { ospfv3AreaLsdbEntry 1 } 
 
ospfv3AreaLsdbType OBJECT-TYPE 
        SYNTAX          Unsigned32 (0..4294967295)
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The type  of  the  link  state  advertisement. 
            Each  link state type has a separate advertise- 
            ment format. Area-Scope LSAs unrecognized by the 
            router are also stored in this database." 
        ::= { ospfv3AreaLsdbEntry 2 } 
 
ospfv3AreaLsdbRouterId OBJECT-TYPE 
        SYNTAX          RouterID 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The 32 bit number that uniquely identifies the 
            originating router in the Autonomous System." 
        REFERENCE 
            "OSPF Version 2, Appendix C.1 Global parameters" 
        ::= { ospfv3AreaLsdbEntry 3 } 
 
ospfv3AreaLsdbLsid OBJECT-TYPE 
        SYNTAX          IpAddress 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The Link State ID is an LS Type Specific field 
            containing a unique identifier; 
            it identifies the piece of the  routing  domain 
            that is being described by the advertisement. 
            In contrast to OSPFv2, the LSID has no 
            addressing semantics." 
        ::= { ospfv3AreaLsdbEntry 4 } 
 
-- Note that the OSPF Sequence Number is a 32 bit signed 
-- integer.  It starts with the value '80000001'h, 
-- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h 
-- Thus, a typical sequence number will be very negative. 
 
ospfv3AreaLsdbSequence OBJECT-TYPE 
        SYNTAX          Integer32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The sequence number field is a  signed  32-bit 
            integer.   It  is used to detect old and dupli- 
            cate link state advertisements.  The  space  of 
            sequence  numbers  is  linearly  ordered.   The 
            larger the sequence number the more recent  the 
            advertisement." 
        REFERENCE 
            "OSPF Version  2,  Section  12.1.6  LS  sequence 
            number" 
        ::= { ospfv3AreaLsdbEntry 5 } 
 
ospfv3AreaLsdbAge OBJECT-TYPE 
        SYNTAX          Integer32 -- Should be 0..MaxAge 
                                  -- unless DoNotAge bit is set 
        UNITS           "seconds" 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "This field is the age of the link state adver- 
            tisement in seconds." 
        REFERENCE 
            "OSPF Version 2, Section 12.1.1 LS age" 
        ::= { ospfv3AreaLsdbEntry 6 } 
 
ospfv3AreaLsdbChecksum OBJECT-TYPE 
        SYNTAX          Integer32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "This field is the  checksum  of  the  complete 
            contents  of  the  advertisement, excepting the 
            age field.  The age field is excepted  so  that 
            an   advertisement's  age  can  be  incremented 
            without updating the  checksum.   The  checksum 
            used  is  the same that is used for ISO connec- 
            tionless datagrams; it is commonly referred  to 
            as the Fletcher checksum." 
        REFERENCE 
            "OSPF Version 2, Section 12.1.7 LS checksum" 
        ::= { ospfv3AreaLsdbEntry 7 } 
 
ospfv3AreaLsdbAdvertisement OBJECT-TYPE 
        SYNTAX          OCTET STRING (SIZE (1..65535)) 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The entire Link State Advertisement, including 
            its header." 
        ::= { ospfv3AreaLsdbEntry 8 } 
 
ospfv3AreaLsdbTypeKnown OBJECT-TYPE 
        SYNTAX          TruthValue 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "Is the LSA type recognized by this Router?" 
        ::= { ospfv3AreaLsdbEntry 9 } 
 
-- OSPFv3 Link-Scope Link State Database 
 
-- The Link State Database contains the Link-Scope Link State 
-- Advertisements from the links that the 
-- device is attached to. 
 
ospfv3LinkLsdbTable OBJECT-TYPE 
        SYNTAX          SEQUENCE OF Ospfv3LinkLsdbEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "The OSPFv3 Process's Link-Scope Link State Database." 
        ::= { ospfv3Objects 5 } 
 
ospfv3LinkLsdbEntry OBJECT-TYPE 
        SYNTAX          Ospfv3LinkLsdbEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "A single Link-Scope Link State Advertisement." 
        INDEX           { ospfv3LinkLsdbIfIndex, 
                          ospfv3LinkLsdbType, 
                          ospfv3LinkLsdbRouterId, 
                          ospfv3LinkLsdbLsid } 
        ::= { ospfv3LinkLsdbTable 1 } 
 
Ospfv3LinkLsdbEntry ::= SEQUENCE { 
        ospfv3LinkLsdbIfIndex 
                InterfaceIndex, 
        ospfv3LinkLsdbType 
                Unsigned32, 
        ospfv3LinkLsdbRouterId 
                RouterID, 
        ospfv3LinkLsdbLsid 
                IpAddress, 
        ospfv3LinkLsdbSequence 
                Integer32, 
        ospfv3LinkLsdbAge 
                Integer32, 
        ospfv3LinkLsdbChecksum 
                Integer32, 
        ospfv3LinkLsdbAdvertisement 
                OCTET STRING, 
        ospfv3LinkLsdbTypeKnown 
                TruthValue 
        } 
 
ospfv3LinkLsdbIfIndex OBJECT-TYPE 
        SYNTAX         InterfaceIndex 
        MAX-ACCESS     read-only 
        STATUS         current 
        DESCRIPTION 
            "The identifier of the link from which the LSA 
            was received." 
        REFERENCE 
            "OSPF Version 2, Appendix C.2 Area parameters" 
        ::= { ospfv3LinkLsdbEntry 1 } 
 
ospfv3LinkLsdbType OBJECT-TYPE 
        SYNTAX          Unsigned32 (0..4294967295)
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The type of the link state advertisement. 
            Each link state type has a separate advertise- 
            ment format. Link-Scope LSAs unrecognized by the 
            router are also stored in this database." 
        ::= { ospfv3LinkLsdbEntry 2 } 
 
ospfv3LinkLsdbRouterId OBJECT-TYPE 
        SYNTAX          RouterID 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The 32 bit number that uniquely identifies the 
            originating router in the Autonomous System." 
        REFERENCE 
            "OSPF Version 2, Appendix C.1 Global parameters" 
        ::= { ospfv3LinkLsdbEntry 3 } 
 
ospfv3LinkLsdbLsid OBJECT-TYPE 
        SYNTAX        IpAddress 
        MAX-ACCESS    read-only 
        STATUS        current 
        DESCRIPTION 
            "The Link State ID is an LS Type Specific field 
            containing a unique identifier; 
            it identifies the piece of the  routing  domain 
            that is being described by the advertisement. 
            In contrast to OSPFv2, the LSID has no 
            addressing semantics." 
        ::= { ospfv3LinkLsdbEntry 4 } 
 
-- Note that the OSPF Sequence Number is a 32 bit signed 
-- integer.  It starts with the value '80000001'h, 
-- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h 
-- Thus, a typical sequence number will be very negative. 
 
ospfv3LinkLsdbSequence OBJECT-TYPE 
        SYNTAX          Integer32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The sequence number field is a  signed  32-bit 
            integer.   It  is used to detect old and dupli- 
            cate link state advertisements.  The  space  of 
            sequence  numbers  is  linearly  ordered.   The 
            larger the sequence number the more recent  the 
            advertisement." 
        REFERENCE 
            "OSPF Version  2,  Section  12.1.6  LS  sequence 
            number" 
        ::= { ospfv3LinkLsdbEntry 5 } 
 
ospfv3LinkLsdbAge OBJECT-TYPE 
        SYNTAX          Integer32 -- Should be 0..MaxAge 
                                  -- unless DoNotAge bit is set 
        UNITS           "seconds" 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "This field is the age of the link state 
            advertisement in seconds." 
        REFERENCE 
            "OSPF Version 2, Section 12.1.1 LS age" 
        ::= { ospfv3LinkLsdbEntry 6 } 
 
ospfv3LinkLsdbChecksum OBJECT-TYPE 
        SYNTAX          Integer32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "This field is the  checksum  of  the  complete 
            contents  of  the  advertisement, excepting the 
            age field.  The age field is excepted  so  that 
            an   advertisement's  age  can  be  incremented 
            without updating the  checksum.   The  checksum 
            used  is  the same that is used for ISO connec- 
            tionless datagrams; it is commonly referred  to 
            as the Fletcher checksum." 
        REFERENCE 
            "OSPF Version 2, Section 12.1.7 LS checksum" 
        ::= { ospfv3LinkLsdbEntry 7 } 
 
ospfv3LinkLsdbAdvertisement OBJECT-TYPE 
        SYNTAX          OCTET STRING (SIZE (1..65535)) 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The entire Link State Advertisement, including 
            its header." 
        ::= { ospfv3LinkLsdbEntry 8 } 
 
ospfv3LinkLsdbTypeKnown OBJECT-TYPE 
        SYNTAX          TruthValue 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "Indicates whether the LSA type is recognized by this 
             Router." 
        ::= { ospfv3LinkLsdbEntry 9 } 
 
 
-- OSPF Host Table 
 
-- The Host/Metric Table indicates what hosts are directly 
-- attached to the Router, and what metrics and types of 
-- service should be advertised for them. 
 
ospfv3HostTable OBJECT-TYPE 
        SYNTAX          SEQUENCE OF Ospfv3HostEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "The list of Hosts, and their metrics, that the 
            router will advertise as host routes." 
        REFERENCE 
            "OSPF Version 2, Appendix C.6  Host route param- 
            eters" 
        ::= { ospfv3Objects 6 } 
 
ospfv3HostEntry OBJECT-TYPE 
        SYNTAX          Ospfv3HostEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "A metric to be advertised when a given host is 
            reachable." 
        INDEX           { ospfv3HostAddressType, 
                          ospfv3HostAddress } 
        ::= { ospfv3HostTable 1 } 
 
Ospfv3HostEntry ::= SEQUENCE { 
        ospfv3HostAddressType 
                InetAddressType, 
        ospfv3HostAddress 
                InetAddress, 
        ospfv3HostMetric 
                Metric, 
        ospfv3HostStatus 
                RowStatus, 
        ospfv3HostAreaID 
                AreaID 
        } 
 
ospfv3HostAddressType OBJECT-TYPE 
        SYNTAX          InetAddressType 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The address type of ospfv3HostAddress. Only IPv6 
            addresses without zone index are expected." 
        REFERENCE 
            "OSPF Version 2, Appendix C.6 Host route parame- 
            ters" 
        ::= { ospfv3HostEntry 1 } 
 
 
ospfv3HostAddress OBJECT-TYPE 
        SYNTAX          InetAddress (SIZE (16)) 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The IPv6 Address of the Host. Must be a Global 
             or Site-local address." 
        REFERENCE 
            "OSPF Version 2, Appendix C.6 Host route parame- 
            ters" 
        ::= { ospfv3HostEntry 2 } 
 
ospfv3HostMetric OBJECT-TYPE 
        SYNTAX          Metric 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The Metric to be advertised." 
        REFERENCE 
            "OSPF Version 2, Appendix C.6 Host route parame- 
            ters" 
        ::= { ospfv3HostEntry 3 } 
 
ospfv3HostStatus OBJECT-TYPE 
        SYNTAX          RowStatus 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "This variable controls the status of  the  en- 
            try. The use of RowStatus is covered in more detail 
            in [6]." 
        ::= { ospfv3HostEntry 4 } 
 
ospfv3HostAreaID OBJECT-TYPE 
        SYNTAX          AreaID 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The Area the Host Entry is to be found within. 
            By  default, the area that a subsuming OSPFv3 in- 
            terface is in, or 0.0.0.0" 
        REFERENCE 
            "OSPF Version 2, Appendix C.2 Area parameters" 
        ::= { ospfv3HostEntry 5 } 
 
-- OSPFv3 Interface Table 
 
ospfv3IfTable OBJECT-TYPE 
        SYNTAX          SEQUENCE OF Ospfv3IfEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "The OSPFv3 Interface Table describes the  inter- 
            faces from the viewpoint of OSPFv3." 
        REFERENCE 
            "OSPF Version 2, Appendix C.3  Router  interface 
            parameters" 
        ::= { ospfv3Objects 7 } 
 
ospfv3IfEntry OBJECT-TYPE 
        SYNTAX          Ospfv3IfEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "The OSPFv3 Interface Entry describes one  inter- 
            face from the viewpoint of OSPFv3." 
        INDEX           { ospfv3IfIndex } 
        ::= { ospfv3IfTable 1 } 
 
 
Ospfv3IfEntry ::= SEQUENCE { 
        ospfv3IfIndex 
                InterfaceIndex, 
        ospfv3IfAreaId 
                AreaID, 
        ospfv3IfType 
                INTEGER, 
        ospfv3IfAdminStat 
                Status, 
        ospfv3IfRtrPriority 
                DesignatedRouterPriority, 
        ospfv3IfTransitDelay 
                UpToRefreshInterval, 
        ospfv3IfRetransInterval 
                UpToRefreshInterval, 
        ospfv3IfHelloInterval 
                HelloRange, 
        ospfv3IfRtrDeadInterval 
                 RouterDeadRange, 
        ospfv3IfPollInterval 
                Unsigned32, 
        ospfv3IfState 
                INTEGER, 
        ospfv3IfDesignatedRouter 
                RouterID, 
        ospfv3IfBackupDesignatedRouter 
                RouterID, 
        ospfv3IfEvents 
                Counter32, 
        ospfv3IfStatus 
                RowStatus, 
        ospfv3IfMulticastForwarding 
                INTEGER, 
        ospfv3IfDemand 
                TruthValue, 
        ospfv3IfMetricValue 
                Metric, 
        ospfv3IfLinkScopeLsaCount 
                Gauge32, 
        ospfv3IfLinkLsaCksumSum 
                Integer32, 
        ospfv3IfInstId 
                Integer32, 
        ospfv3IfDemandNbrProbe 
                TruthValue, 
        ospfv3IfDemandNbrProbeRetxLimit  
                Unsigned32, 
        ospfv3IfDemandNbrProbeInterval  
                Unsigned32 
        } 
 
ospfv3IfIndex OBJECT-TYPE 
        SYNTAX          InterfaceIndex 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The interface index of this OSPFv3 interface. 
             It corresponds to the interface index of the 
             IPv6 interface on which OSPFv3 is configured." 
        ::= { ospfv3IfEntry 1 } 
 
ospfv3IfAreaId OBJECT-TYPE 
        SYNTAX          AreaID 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "A 32-bit integer uniquely identifying the area 
            to  which  the  interface  connects.   Area  ID 
            0.0.0.0 is used for the OSPFv3 backbone." 
        DEFVAL          { '00000000'H } -- 0.0.0.0 
        ::= { ospfv3IfEntry 2 } 
 
ospfv3IfType OBJECT-TYPE 
        SYNTAX          INTEGER { 
                        broadcast(1), 
                        nbma(2), 
                        pointToPoint(3), 
                        pointToMultipoint(5) 
                        } 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The OSPFv3 interface type." 
        ::= { ospfv3IfEntry 3 } 
 
ospfv3IfAdminStat OBJECT-TYPE 
        SYNTAX          Status 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The OSPFv3 interface's  administrative  status. 
            The  value formed on the interface, and the in- 
            terface will be advertised as an internal route 
            to  some  area.   The  value 'disabled' denotes 
            that the interface is external to OSPFv3." 
        DEFVAL          { enabled } 
        ::= { ospfv3IfEntry 4 } 
 
ospfv3IfRtrPriority OBJECT-TYPE 
        SYNTAX          DesignatedRouterPriority 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The  priority  of  this  interface.   Used  in 
            multi-access  networks,  this  field is used in 
            the designated router election algorithm.   The 
            value 0 signifies that the router is not eligi- 
            ble to become the  designated  router  on  this 
            particular  network.   In the event of a tie in 
            this value, routers will use their Router ID as 
            a tie breaker." 
        DEFVAL          { 1 } 
        ::= { ospfv3IfEntry 5 } 
 
ospfv3IfTransitDelay OBJECT-TYPE 
        SYNTAX          UpToRefreshInterval 
        UNITS           "seconds" 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The estimated number of seconds  it  takes  to 
            transmit  a  link state update packet over this 
            interface." 
        DEFVAL          { 1 } 
        ::= { ospfv3IfEntry 6 } 
 
ospfv3IfRetransInterval OBJECT-TYPE 
        SYNTAX          UpToRefreshInterval 
        UNITS           "seconds" 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The number of seconds between  link-state  ad- 
            vertisement  retransmissions,  for  adjacencies 
            belonging to this  interface.   This  value  is 
            also used when retransmitting database descrip- 
            tion and link-state request packets." 
        DEFVAL          { 5 } 
        ::= { ospfv3IfEntry 7 } 
 
ospfv3IfHelloInterval OBJECT-TYPE 
        SYNTAX          HelloRange 
        UNITS           "seconds" 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The length of time, in  seconds,  between  the 
            Hello  packets that the router sends on the in- 
            terface.  This value must be the same  for  all 
            routers attached to a common network." 
        DEFVAL          { 10 } 
        ::= { ospfv3IfEntry 8 } 
 
ospfv3IfRtrDeadInterval OBJECT-TYPE 
        SYNTAX          RouterDeadRange 
        UNITS           "seconds" 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The number of seconds that  a  router's  Hello 
            packets  have  not been seen before it's neigh- 
            bors declare the router down.  This  should  be 
            some  multiple  of  the  Hello  interval.  This 
            value must be the same for all routers attached 
            to a common network." 
        DEFVAL          { 40 } 
        ::= { ospfv3IfEntry 9 } 
 
ospfv3IfPollInterval OBJECT-TYPE 
        SYNTAX          Unsigned32 
        UNITS           "seconds" 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The larger time interval, in seconds,  between 
            the  Hello  packets  sent  to  an inactive non- 
            broadcast multi- access neighbor." 
        DEFVAL          { 120 } 
        ::= { ospfv3IfEntry 10 } 
 
ospfv3IfState OBJECT-TYPE 
        SYNTAX          INTEGER { 
                        down(1), 
                        loopback(2), 
                        waiting(3), 
                        pointToPoint(4), 
                        designatedRouter(5), 
                        backupDesignatedRouter(6), 
                        otherDesignatedRouter(7) 
                        } 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The OSPFv3 Interface State." 
        ::= { ospfv3IfEntry 11 } 
 
ospfv3IfDesignatedRouter OBJECT-TYPE 
        SYNTAX          RouterID 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The Router ID of the Designated Router." 
        ::= { ospfv3IfEntry 12 } 
 
ospfv3IfBackupDesignatedRouter OBJECT-TYPE 
        SYNTAX          RouterID 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The  Router ID of  the  Backup   Designated 
            Router." 
        ::= { ospfv3IfEntry 14 } 
 
ospfv3IfEvents OBJECT-TYPE 
        SYNTAX          Counter32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The number of times this  OSPF  interface  has 
            changed its state, or an error has occurred." 
        ::= { ospfv3IfEntry 15 } 
 
 ospfv3IfStatus OBJECT-TYPE 
        SYNTAX          RowStatus 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "This variable controls the status of  the  en- 
            try. The use of RowStatus is covered in more detail in 
            [6]." 
        ::= { ospfv3IfEntry 17 } 
 
ospfv3IfMulticastForwarding OBJECT-TYPE 
        SYNTAX          INTEGER { 
                        blocked(1),   -- no multicast forwarding 
                        multicast(2), -- using multicast address 
                        unicast(3)    -- to each OSPFv3 neighbor 
                        } 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The way multicasts should  forwarded  on  this 
            interface;  not  forwarded,  forwarded  as data 
            link multicasts, or forwarded as data link uni- 
            casts.   Data link multicasting is not meaning- 
            ful on point to point and NBMA interfaces,  and 
            setting ospfv3MulticastForwarding to 0 effective- 
            ly disables all multicast forwarding." 
        DEFVAL { blocked } 
        ::= { ospfv3IfEntry 18 } 
 
ospfv3IfDemand OBJECT-TYPE 
        SYNTAX          TruthValue 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "Indicates whether Demand OSPFv3 procedures (hel- 
            lo suppression to FULL neighbors and setting the 
            DoNotAge flag on propagated LSAs) should be per- 
            formed on this interface." 
        DEFVAL { false } 
        ::= { ospfv3IfEntry 19 } 
 
ospfv3IfMetricValue OBJECT-TYPE 
        SYNTAX          Metric 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The metric assigned to this interface. 
             The default value of the Metric is 
            Reference Bandwidth / ifSpeed. The value of the   
            reference bandwidth is configured by the 
            ospfv3ReferenceBandwidth object." 
        ::= { ospfv3IfEntry 20 } 
 
 ospfv3IfLinkScopeLsaCount OBJECT-TYPE 
        SYNTAX          Gauge32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The total number of Link-Scope link-state 
            advertisements in  this  link's link-state database." 
        ::= { ospfv3IfEntry 21 } 
 
 ospfv3IfLinkLsaCksumSum OBJECT-TYPE 
        SYNTAX          Integer32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The 32-bit unsigned sum of the Link-Scope link-state 
            advertisements'  LS  checksums  contained in this 
            link's link-state database.  The sum can be used 
            to determine if  there  has been  a  change  in a 
            router's link state database, and to compare the 
            link-state database of two routers." 
        ::= { ospfv3IfEntry 22 } 
 
ospfv3IfInstId OBJECT-TYPE 
        SYNTAX          Integer32 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "Enables multiple instances of OSPFv3 to be run over 
            a single link. Each protocol instance would be assigned 
            a separate ID. This ID has local link significance 
            only." 
        DEFVAL          { 0 } 
        ::= { ospfv3IfEntry 23 } 
 
ospfv3IfDemandNbrProbe OBJECT-TYPE 
        SYNTAX          TruthValue 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
               " Indicates whether or not neighbor probing is 
                 enabled to determine whether or not the neighbor  
                 is inactive. Neighbor probing is disabled by  
                 default." 
        DEFVAL { false } 
        ::= { ospfv3IfEntry 24 } 
 
   ospfv3IfDemandNbrProbeRetxLimit OBJECT-TYPE  
       SYNTAX       Unsigned32  
       UNITS        "seconds"  
       MAX-ACCESS   read-create 
       STATUS       current  
       DESCRIPTION  
          " The number of consecutive LSA retransmissions before 
            the neighbor is deemed inactive and the neighbor  
            adjacency is brought down."  
       DEFVAL          { 10 } 
       ::= { ospfv3IfEntry 25 }  
 
 
   ospfv3IfDemandNbrProbeInterval OBJECT-TYPE  
       SYNTAX       Unsigned32  
       UNITS        "seconds"  
       MAX-ACCESS   read-create 
       STATUS       current  
       DESCRIPTION  
          " Defines how often the neighbor will be probed."  
       DEFVAL          { 120 } 
       ::= { ospfv3IfEntry 26 }  
 
 
-- OSPFv3 Virtual Interface Table 
 
-- The Virtual Interface Table describes the virtual 
-- links that the OSPFv3 Process is configured to 
-- carry on. 
 
ospfv3VirtIfTable OBJECT-TYPE 
        SYNTAX          SEQUENCE OF Ospfv3VirtIfEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "Information about this router's virtual inter- 
            faces." 
        REFERENCE 
            "OSPF Version  2,  Appendix  C.4   Virtual  link 
            parameters" 
        ::= { ospfv3Objects 8 } 
 
ospfv3VirtIfEntry OBJECT-TYPE 
        SYNTAX          Ospfv3VirtIfEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "Information about a single Virtual Interface." 
        INDEX           { ospfv3VirtIfAreaId, 
                          ospfv3VirtIfNeighbor } 
        ::= { ospfv3VirtIfTable 1 } 
 
Ospfv3VirtIfEntry ::= SEQUENCE { 
        ospfv3VirtIfAreaId 
                AreaID, 
        ospfv3VirtIfNeighbor 
                RouterID, 
        ospfv3VirtIfIndex 
                InterfaceIndex, 
        ospfv3VirtIfTransitDelay 
                UpToRefreshInterval, 
        ospfv3VirtIfRetransInterval 
                UpToRefreshInterval, 
        ospfv3VirtIfHelloInterval 
                HelloRange, 
        ospfv3VirtIfRtrDeadInterval 
                 RouterDeadRange, 
        ospfv3VirtIfState 
                INTEGER, 
        ospfv3VirtIfEvents 
                Counter32, 
        ospfv3VirtIfStatus 
                RowStatus, 
        ospfv3VirtIfLinkScopeLsaCount 
                Gauge32, 
        ospfv3VirtIfLinkLsaCksumSum 
                   Integer32 
        } 
 
ospfv3VirtIfAreaId OBJECT-TYPE 
        SYNTAX          AreaID 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The  Transit  Area  that  the   Virtual   Link 
            traverses.  By definition, this is not 0.0.0.0" 
        ::= { ospfv3VirtIfEntry 1 } 
 
ospfv3VirtIfNeighbor OBJECT-TYPE 
        SYNTAX          RouterID 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The Router ID of the Virtual Neighbor." 
        ::= { ospfv3VirtIfEntry 2 } 
 
ospfv3VirtIfIndex OBJECT-TYPE 
        SYNTAX          InterfaceIndex 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The interface ID assigned to this OSPFv3 virtual 
            interface. It is advertised in Hello's sent over 
            the virtal link and in the router's router-LSAs." 
        ::= { ospfv3VirtIfEntry 3 } 
 
ospfv3VirtIfTransitDelay OBJECT-TYPE 
        SYNTAX          UpToRefreshInterval 
        UNITS           "seconds" 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The estimated number of seconds  it  takes  to 
            transmit  a link- state update packet over this 
            interface." 
        DEFVAL          { 1 } 
        ::= { ospfv3VirtIfEntry 4 } 
 
ospfv3VirtIfRetransInterval OBJECT-TYPE 
        SYNTAX          UpToRefreshInterval 
        UNITS           "seconds" 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The number of seconds between  link-state  ad- 
            vertisement  retransmissions,  for  adjacencies 
            belonging to this  interface.   This  value  is 
            also used when retransmitting database descrip- 
            tion  and  link-state  request  packets.   This 
            value  should  be well over the expected round- 
            trip time." 
        DEFVAL          { 5 } 
        ::= { ospfv3VirtIfEntry 5 } 
 
ospfv3VirtIfHelloInterval OBJECT-TYPE 
        SYNTAX          HelloRange 
        UNITS           "seconds" 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The length of time, in  seconds,  between  the 
            Hello  packets that the router sends on the in- 
            terface.  This value must be the same  for  the 
            virtual neighbor." 
        DEFVAL          { 10 } 
        ::= { ospfv3VirtIfEntry 6 } 
 
ospfv3VirtIfRtrDeadInterval OBJECT-TYPE 
        SYNTAX          RouterDeadRange 
        UNITS           "seconds" 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The number of seconds that  a  router's  Hello 
            packets  have  not been seen before it's neigh- 
            bors declare the router down.  This  should  be 
            some  multiple  of  the  Hello  interval.  This 
            value must be the same for the  virtual  neigh- 
            bor." 
        DEFVAL          { 60 } 
        ::= { ospfv3VirtIfEntry 7 } 
 
ospfv3VirtIfState OBJECT-TYPE 
        SYNTAX          INTEGER { 
                        down(1), -- these use the same encoding 
                        pointToPoint(4) -- as the ospfv3IfTable 
                        } 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "OSPF virtual interface states." 
        ::= { ospfv3VirtIfEntry 8 } 
 
ospfv3VirtIfEvents OBJECT-TYPE 
        SYNTAX          Counter32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The number of state changes or error events on 
            this Virtual Link" 
        ::= { ospfv3VirtIfEntry 9 } 
 
ospfv3VirtIfStatus OBJECT-TYPE 
        SYNTAX          RowStatus 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "This variable controls the status of  the  en- 
            try. The use of RowStatus is covered in more detail 
            in [6]." 
        ::= { ospfv3VirtIfEntry 10 } 
 
ospfv3VirtIfLinkScopeLsaCount OBJECT-TYPE 
        SYNTAX          Gauge32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The total number of Link-Scope link-state 
            advertisements in  this  virtual link's link-state 
            database." 
        ::= { ospfv3VirtIfEntry 11 } 
 
ospfv3VirtIfLinkLsaCksumSum OBJECT-TYPE 
        SYNTAX          Integer32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The 32-bit unsigned sum of the Link-Scope link-state 
            advertisements'  LS  checksums  contained in this 
            virtual link's link-state database.  The sum can be used 
            to determine if  there  has been  a  change  in a 
            router's link state database, and to compare the 
            link-state database of two routers." 
        ::= { ospfv3VirtIfEntry 12 } 
 
 
-- OSPFv3 Neighbor Table 
 
-- The OSPFv3 Neighbor Table describes all neighbors in 
-- the locality of the subject router. 
 
ospfv3NbrTable OBJECT-TYPE 
        SYNTAX          SEQUENCE OF Ospfv3NbrEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "A table of non-virtual neighbor information." 
        REFERENCE 
            "OSPF Version 2, Section 10  The  Neighbor  Data 
            Structure" 
        ::= { ospfv3Objects 9 } 
 
ospfv3NbrEntry OBJECT-TYPE 
        SYNTAX          Ospfv3NbrEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "The information regarding a single neighbor." 
        REFERENCE 
            "OSPF Version 2, Section 10  The  Neighbor  Data 
            Structure" 
        INDEX           { ospfv3NbrIfIndex, 
                          ospfv3NbrRtrId } 
        ::= { ospfv3NbrTable 1 } 
 
Ospfv3NbrEntry ::= SEQUENCE { 
        ospfv3NbrIfIndex 
                InterfaceIndex, 
        ospfv3NbrRtrId 
                RouterID, 
        ospfv3NbrAddressType 
                InetAddressType, 
        ospfv3NbrAddress 
                InetAddress,             
        ospfv3NbrOptions 
                Integer32, 
        ospfv3NbrPriority 
                DesignatedRouterPriority, 
        ospfv3NbrState 
                INTEGER, 
        ospfv3NbrEvents 
                Counter32, 
        ospfv3NbrLsRetransQLen 
                Gauge32, 
        ospfv3NbrHelloSuppressed 
                TruthValue, 
        ospfv3NbrIfId 
                InterfaceIndex, 
        ospfv3NbrRestartHelperStatus  
                INTEGER,  
        ospfv3NbrRestartHelperAge  
                UpToRefreshInterval,  
        ospfv3NbrRestartHelperExitReason  
                INTEGER 
        } 
 
ospfv3NbrIfIndex OBJECT-TYPE 
        SYNTAX          InterfaceIndex 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The local link ID of the link over which the 
             neighbor can be reached." 
        ::= { ospfv3NbrEntry 1 } 
 
ospfv3NbrRtrId OBJECT-TYPE 
        SYNTAX          RouterID 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "A 32-bit integer (represented as a type  IpAd- 
            dress)  uniquely  identifying  the  neighboring 
            router in the Autonomous System." 
        ::= { ospfv3NbrEntry 2 } 
 
ospfv3NbrAddressType OBJECT-TYPE 
        SYNTAX          InetAddressType 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The address type of ospfv3NbrAddress. Only IPv6 
            addresses without zone index are expected." 
        ::= { ospfv3NbrEntry 3 } 
 
ospfv3NbrAddress OBJECT-TYPE 
        SYNTAX          InetAddress (SIZE (16)) 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The IPv6 address of the neighbor associated with 
            the local link." 
        ::= { ospfv3NbrEntry 4 } 
 
ospfv3NbrOptions OBJECT-TYPE 
        SYNTAX          Integer32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "A Bit Mask corresponding to the neighbor's op- 
            tions field." 
        REFERENCE 
            "OSPF Version 3, Appendix A.2 the Options field" 
        ::= { ospfv3NbrEntry 5 } 
 
ospfv3NbrPriority OBJECT-TYPE 
        SYNTAX          DesignatedRouterPriority 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The priority of this neighbor in the designat- 
            ed router election algorithm.  The value 0 sig- 
            nifies that the neighbor is not eligible to be- 
            come  the  designated router on this particular 
            network." 
        ::= { ospfv3NbrEntry 6 } 
 
ospfv3NbrState OBJECT-TYPE 
        SYNTAX          INTEGER { 
                        down(1), 
                        attempt(2), 
                        init(3), 
                        twoWay(4), 
                        exchangeStart(5), 
                        exchange(6), 
                        loading(7), 
                        full(8) 
                        } 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The State of the relationship with this Neigh- 
            bor." 
        REFERENCE 
            "OSPF Version 2, Section 10.1 Neighbor States" 
        ::= { ospfv3NbrEntry 7 } 
 
ospfv3NbrEvents OBJECT-TYPE 
        SYNTAX          Counter32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The number of times this neighbor relationship 
            has changed state, or an error has occurred." 
        ::= { ospfv3NbrEntry 8 } 
 
ospfv3NbrLsRetransQLen OBJECT-TYPE 
        SYNTAX          Gauge32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The  current  length  of  the   retransmission 
            queue." 
        ::= { ospfv3NbrEntry 9 } 
 
ospfv3NbrHelloSuppressed OBJECT-TYPE 
        SYNTAX          TruthValue 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "Indicates whether Hellos are being  suppressed 
            to the neighbor" 
        ::= { ospfv3NbrEntry 10 } 
 
ospfv3NbrIfId OBJECT-TYPE 
        SYNTAX          InterfaceIndex 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The interface ID that the neighbor advertises 
            in its Hello Packets on this link, that is, the 
            neighbor's local interface index." 
        ::= { ospfv3NbrEntry 11 } 
 
ospfv3NbrRestartHelperStatus OBJECT-TYPE  
       SYNTAX       INTEGER { notHelping (1),  
                              helping (2)  
                            }  
       MAX-ACCESS   read-only  
       STATUS       current  
       DESCRIPTION  
          "Indicates whether the router is acting  
          as a hitless restart helper for the neighbor."  
          ::= { ospfv3NbrEntry 12 }  
    
ospfv3NbrRestartHelperAge OBJECT-TYPE  
       SYNTAX       UpToRefreshInterval 
       UNITS        "seconds"  
       MAX-ACCESS   read-only  
       STATUS       current  
       DESCRIPTION  
          "Remaining time in current OSPF hitless restart  
          interval, if the router is acting as a restart  
          helper for the neighbor."  
       ::= { ospfv3NbrEntry 13 }  
    
ospfv3NbrRestartHelperExitReason OBJECT-TYPE  
       SYNTAX       INTEGER { none (1),           -- not attempted  
                              inProgress (2),     -- restart in  
                                                  -- progress  
                              completed (3),      -- successfully  
                                                  -- completed  
                              timedOut (4),       -- timed out  
                              topologyChanged (5) -- aborted due to  
                                                  -- topology  
                                                  -- change.  
                            }  
       MAX-ACCESS   read-only  
       STATUS       current  
       DESCRIPTION  
          "Describes the outcome of the last attempt at acting  
           as a hitless restart helper for the neighbor."  
    ::= { ospfv3NbrEntry 14 } 
 
 
-- OSPFv3 NBMA Neighbor Table 
 
-- The OSPFv3 NBMA Neighbor Table describes all configured 
-- NBMA neighbors and neighbors dynamically discovered by 
-- lower-level protocols such as Inverse Neighbor Discovery. 
 
ospfv3NbmaNbrTable OBJECT-TYPE 
        SYNTAX          SEQUENCE OF Ospfv3NbmaNbrEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "A table of configured non-virtual neighbor 
            information and neighbors dynamically discovered 
            by lower-level protocols such as Inverse Neighbor 
            Discovery." 
        REFERENCE 
            "OSPF Version 2, Section 10  The  Neighbor  Data 
            Structure" 
        ::= { ospfv3Objects 10 } 
 
ospfv3NbmaNbrEntry OBJECT-TYPE 
        SYNTAX          Ospfv3NbmaNbrEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "The information regarding a single configured 
            neighbor or neighbor discovered by lower-level 
            protocols such as Inverse Neighbor Discovery." 
        REFERENCE 
            "OSPF Version 2, Section 10  The  Neighbor  Data 
            Structure" 
        INDEX           { ospfv3NbmaNbrIfIndex, 
                          ospfv3NbmaNbrAddressType, 
                          ospfv3NbmaNbrAddress } 
        ::= { ospfv3NbmaNbrTable 1 } 
 
Ospfv3NbmaNbrEntry ::= SEQUENCE { 
        ospfv3NbmaNbrIfIndex 
                InterfaceIndex, 
        ospfv3NbmaNbrAddressType 
                InetAddressType, 
        ospfv3NbmaNbrAddress 
                InetAddress, 
        ospfv3NbmaNbrPriority 
                DesignatedRouterPriority, 
        ospfv3NbmaNbrRtrId 
                RouterID, 
        ospfv3NbmaNbrState 
                INTEGER, 
        ospfv3NbmaNbrStorageType 
                StorageType, 
        ospfv3NbmaNbrStatus 
                RowStatus 
        } 
 
ospfv3NbmaNbrIfIndex OBJECT-TYPE 
        SYNTAX          InterfaceIndex 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The local link ID of the link over which the 
             neighbor can be reached." 
        ::= { ospfv3NbmaNbrEntry 1 } 
 
ospfv3NbmaNbrAddressType OBJECT-TYPE 
        SYNTAX          InetAddressType 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The address type of ospfv3NbrAddress. Only IPv6 
            addresses without zone index are expected." 
        ::= { ospfv3NbmaNbrEntry 2 } 
 
ospfv3NbmaNbrAddress OBJECT-TYPE 
        SYNTAX          InetAddress (SIZE (16)) 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The IPv6 address of the neighbor associated with 
            the local link." 
        ::= { ospfv3NbmaNbrEntry 3 } 
 
ospfv3NbmaNbrPriority OBJECT-TYPE 
        SYNTAX          DesignatedRouterPriority 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The priority of this neighbor in the designat- 
            ed router election algorithm. The value 0 sig- 
            nifies that the neighbor is not eligible to be- 
            come  the  designated router on this particular 
            network." 
        DEFVAL          { 1 } 
        ::= { ospfv3NbmaNbrEntry 4 } 
 
ospfv3NbmaNbrRtrId OBJECT-TYPE 
        SYNTAX          RouterID 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "A 32-bit integer (represented as a type IpAd- 
            dress) uniquely identifying the neighboring 
            router in the Autonomous System. A value of 
            0.0.0.0 is returned until a Hello is received 
            from the configured neighbor." 
        ::= { ospfv3NbmaNbrEntry 5 } 
 
ospfv3NbmaNbrState OBJECT-TYPE 
        SYNTAX          INTEGER { 
                        down(1), 
                        attempt(2), 
                        init(3), 
                        twoWay(4), 
                        exchangeStart(5), 
                        exchange(6), 
                        loading(7), 
                        full(8) 
                        } 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The State of the relationship with this Neigh- 
            bor." 
        REFERENCE 
            "OSPF Version 2, Section 10.1 Neighbor States" 
        ::= { ospfv3NbmaNbrEntry 6 } 
 
ospfv3NbmaNbrStorageType OBJECT-TYPE 
        SYNTAX          StorageType 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "The storage type for this conceptual row. 
            Conceptual rows having the value 'permanent' need not 
            allow write-access to any columnar objects in the row. 
            Manually configured entries will have a storage type 
            of nonVolatile while entries dynamically created as a 
            result of a lower-level protocol such as Inverse 
            Neighbor Discovery will have a storage type of 
            volatile." 
        DEFVAL          { nonVolatile } 
        ::= { ospfv3NbmaNbrEntry 7 } 
 
ospfv3NbmaNbrStatus OBJECT-TYPE 
        SYNTAX          RowStatus 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "This variable controls the status of the en- 
            try. The use of RowStatus is covered in more detail 
            in [6]." 
        ::= { ospfv3NbmaNbrEntry 8 } 
 
-- OSPFv3 Virtual Neighbor Table 
 
-- This table describes all virtual neighbors. 
-- Since Virtual Links are configured in the 
-- virtual interface table, this table is read-only. 
 
ospfv3VirtNbrTable OBJECT-TYPE 
        SYNTAX          SEQUENCE OF Ospfv3VirtNbrEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "A table of virtual neighbor information." 
        REFERENCE 
            "OSPF Version 2, Section 15 Virtual Links" 
        ::= { ospfv3Objects 11 } 
 
ospfv3VirtNbrEntry OBJECT-TYPE 
        SYNTAX          Ospfv3VirtNbrEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "Virtual neighbor information." 
        INDEX           { ospfv3VirtNbrArea, 
                          ospfv3VirtNbrRtrId } 
        ::= { ospfv3VirtNbrTable 1 } 
 
Ospfv3VirtNbrEntry ::= SEQUENCE { 
        ospfv3VirtNbrArea 
                AreaID, 
        ospfv3VirtNbrRtrId 
                RouterID, 
        ospfv3VirtNbrIfIndex 
                InterfaceIndex, 
        ospfv3VirtNbrAddressType 
                InetAddressType, 
        ospfv3VirtNbrAddress 
                InetAddress, 
        ospfv3VirtNbrOptions 
                Integer32, 
        ospfv3VirtNbrState 
                INTEGER, 
        ospfv3VirtNbrEvents 
                Counter32, 
        ospfv3VirtNbrLsRetransQLen 
                Gauge32, 
        ospfv3VirtNbrHelloSuppressed 
                TruthValue, 
        ospfv3VirtNbrIfId 
                InterfaceIndex, 
        ospfv3VirtNbrRestartHelperStatus  
                INTEGER,  
        ospfv3VirtNbrRestartHelperAge  
                UpToRefreshInterval,  
        ospfv3VirtNbrRestartHelperExitReason  
                INTEGER 
        } 
 
ospfv3VirtNbrArea OBJECT-TYPE 
        SYNTAX          AreaID 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The Transit Area Identifier." 
        ::= { ospfv3VirtNbrEntry 1 } 
 
ospfv3VirtNbrRtrId OBJECT-TYPE 
        SYNTAX          RouterID 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "A  32-bit  integer  uniquely  identifying  the 
            neighboring router in the Autonomous System." 
        ::= { ospfv3VirtNbrEntry 2 } 
 
ospfv3VirtNbrIfIndex OBJECT-TYPE 
        SYNTAX          InterfaceIndex 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The local interface ID for the virtual link over 
            which the neighbor can be reached." 
        ::= { ospfv3VirtNbrEntry 3 } 
 
ospfv3VirtNbrAddressType OBJECT-TYPE 
        SYNTAX          InetAddressType 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The address type of ospfv3VirtNbrAddress. Only IPv6 
            addresses without zone index are expected." 
        ::= { ospfv3VirtNbrEntry 4 } 
 
ospfv3VirtNbrAddress OBJECT-TYPE 
        SYNTAX          InetAddress (SIZE (16)) 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The IPv6 address advertised by this Virtual Neighbor. 
            It must be a Site-Local or Global scope address." 
        ::= { ospfv3VirtNbrEntry 5 } 
 
ospfv3VirtNbrOptions OBJECT-TYPE 
        SYNTAX          Integer32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "A Bit Mask corresponding to the neighbor's op- 
            tions field." 
        REFERENCE 
            "OSPF Version 3, Appendix A.2 the Options field" 
        ::= { ospfv3VirtNbrEntry 6 } 
 
ospfv3VirtNbrState OBJECT-TYPE 
        SYNTAX          INTEGER { 
                        down(1), 
                        attempt(2), 
                        init(3), 
                        twoWay(4), 
                        exchangeStart(5), 
                        exchange(6), 
                        loading(7), 
                        full(8) 
                        } 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The state of the Virtual Neighbor Relation- 
            ship." 
        ::= { ospfv3VirtNbrEntry 7 } 
 
ospfv3VirtNbrEvents OBJECT-TYPE 
        SYNTAX          Counter32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The number of  times  this  virtual  link  has 
            changed its state, or an error has occurred." 
        ::= { ospfv3VirtNbrEntry 8 } 
 
ospfv3VirtNbrLsRetransQLen OBJECT-TYPE 
        SYNTAX          Gauge32 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The  current  length  of  the   retransmission 
            queue." 
        ::= { ospfv3VirtNbrEntry 9 } 
 
ospfv3VirtNbrHelloSuppressed OBJECT-TYPE 
        SYNTAX          TruthValue 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "Indicates whether Hellos are being  suppressed 
            to the neighbor" 
        ::= { ospfv3VirtNbrEntry 10 } 
 
ospfv3VirtNbrIfId OBJECT-TYPE 
        SYNTAX          InterfaceIndex 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The interface ID that the neighbor advertises 
            in its Hello Packets on this virtual link, that is, 
            the neighbor's local interface ID." 
        ::= { ospfv3VirtNbrEntry 11 } 
 
   ospfv3VirtNbrRestartHelperStatus OBJECT-TYPE  
       SYNTAX       INTEGER { notHelping (1),  
                              helping (2)  
                            }  
       MAX-ACCESS   read-only  
       STATUS       current  
       DESCRIPTION  
          "Indicates whether the router is acting  
          as a hitless restart helper for the neighbor."  
          ::= { ospfv3VirtNbrEntry 12 }  
    
ospfv3VirtNbrRestartHelperAge OBJECT-TYPE  
       SYNTAX       UpToRefreshInterval 
       UNITS        "seconds"  
       MAX-ACCESS   read-only  
       STATUS       current  
       DESCRIPTION  
          "Remaining time in current OSPF hitless restart  
          interval, if the router is acting as a restart  
          helper for the neighbor."  
       ::= { ospfv3VirtNbrEntry 13 }  
    
ospfv3VirtNbrRestartHelperExitReason OBJECT-TYPE  
       SYNTAX       INTEGER { none (1),           -- not attempted  
                              inProgress (2),     -- restart in  
                                                  -- progress  
                              completed (3),      -- successfully  
                                                  -- completed  
                              timedOut (4),       -- timed out  
                              topologyChanged (5) -- aborted due to  
                                                  -- topology  
                                                  -- change.  
                            }  
       MAX-ACCESS   read-only  
       STATUS       current  
       DESCRIPTION  
          "Describes the outcome of the last attempt at acting  
           as a hitless restart helper for the neighbor."  
    ::= { ospfv3VirtNbrEntry 14 } 
 
 
-- 
-- The OSPFv3 Area Aggregate Table 
-- 
 
ospfv3AreaAggregateTable OBJECT-TYPE 
        SYNTAX          SEQUENCE OF Ospfv3AreaAggregateEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "A range of IPv6 prefixes specified by a 
            prefix/prefix length  pair. Note that if 
            ranges are configured such that one range sub- 
            sumes  another range the most specific match is 
            the preferred one." 
        ::= { ospfv3Objects 12 } 
 
ospfv3AreaAggregateEntry OBJECT-TYPE 
        SYNTAX          Ospfv3AreaAggregateEntry 
        MAX-ACCESS      not-accessible 
        STATUS          current 
        DESCRIPTION 
            "A range of IPv6 prefixes specified by a 
            prefix/prefix length  pair. Note that if 
            ranges are configured such that one range sub- 
            sumes  another range the most specific match is 
            the preferred one." 
        REFERENCE 
            "OSPF Version 2, Appendix C.2  Area parameters" 
        INDEX           { ospfv3AreaAggregateAreaID,  
                          ospfv3AreaAggregateAreaLsdbType, 
                          ospfv3AreaAggregatePrefixType, 
                          ospfv3AreaAggregatePrefix, 
                          ospfv3AreaAggregatePrefixLength } 
        ::= { ospfv3AreaAggregateTable 1 } 
 
Ospfv3AreaAggregateEntry ::= SEQUENCE { 
        ospfv3AreaAggregateAreaID 
                AreaID, 
        ospfv3AreaAggregateAreaLsdbType 
                INTEGER, 
        ospfv3AreaAggregatePrefixType 
                InetAddressType, 
        ospfv3AreaAggregatePrefix 
                InetAddress, 
        ospfv3AreaAggregatePrefixLength 
                InetAddressPrefixLength, 
        ospfv3AreaAggregateStatus 
                RowStatus, 
        ospfv3AreaAggregateEffect 
                INTEGER, 
        ospfv3AreaAggregateRouteTag 
                INTEGER 
        } 
 
ospfv3AreaAggregateAreaID OBJECT-TYPE 
        SYNTAX          AreaID 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The Area the Address Aggregate is to be  found 
            within." 
        REFERENCE 
            "OSPF Version 2, Appendix C.2 Area parameters" 
        ::= { ospfv3AreaAggregateEntry 1 } 
 
ospfv3AreaAggregateAreaLsdbType OBJECT-TYPE 
        SYNTAX          INTEGER { 
                        interAreaPrefixLsa(8195), -- 0x2003 
                        nssaExternalLsa(8199)     -- 0x2007 
                        } 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The type of the Address Aggregate.  This field 
            specifies  the  Area Lsdb type that this Address Ag- 
            gregate applies to." 
        REFERENCE 
            "OSPF Version 2, Appendix A.4.1 The  Link  State 
            Advertisement header" 
        ::= { ospfv3AreaAggregateEntry 2 } 
 
ospfv3AreaAggregatePrefixType OBJECT-TYPE 
        SYNTAX          InetAddressType 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The prefix type of ospfv3AreaAggregatePrefix. Only 
            IPv6 addresses are expected." 
        ::= { ospfv3AreaAggregateEntry 4 } 
 
ospfv3AreaAggregatePrefix OBJECT-TYPE 
        SYNTAX          InetAddress (SIZE (0..16)) 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The IPv6 Prefix." 
        REFERENCE 
            "OSPF Version 2, Appendix C.2 Area parameters" 
        ::= { ospfv3AreaAggregateEntry 5 } 
 
ospfv3AreaAggregatePrefixLength OBJECT-TYPE 
        SYNTAX          InetAddressPrefixLength (3..128) 
        UNITS           "bits" 
        MAX-ACCESS      read-only 
        STATUS          current 
        DESCRIPTION 
            "The length of the prefix (in bits). A prefix can 
            not be shorter than 3 bits." 
        REFERENCE 
            "OSPF Version 2, Appendix C.2 Area parameters" 
        ::= { ospfv3AreaAggregateEntry 6 } 
 
ospfv3AreaAggregateStatus OBJECT-TYPE 
        SYNTAX          RowStatus 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "This variable controls the status of  the  en- 
            try. The use of RowStatus is covered in more detail 
            in [6]." 
        ::= { ospfv3AreaAggregateEntry 7 } 
 
ospfv3AreaAggregateEffect OBJECT-TYPE 
        SYNTAX          INTEGER { 
                        advertiseMatching(1), 
                        doNotAdvertiseMatching(2) 
                        } 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "Prefixes subsumed by ranges either trigger  the 
            advertisement  of  the indicated aggregate (ad- 
            vertiseMatching), or result in the prefix not 
            being advertised at all outside the area." 
        DEFVAL          { advertiseMatching } 
        ::= { ospfv3AreaAggregateEntry 8 } 
 
ospfv3AreaAggregateRouteTag OBJECT-TYPE 
        SYNTAX          Integer32 
        MAX-ACCESS      read-create 
        STATUS          current 
        DESCRIPTION 
            "This tag is advertised only in the summarized 
             As-External LSA when summarizing from type-7 to  
             type-5." 
        DEFVAL         { 0 } 
        ::= { ospfv3AreaAggregateEntry 9 } 
         

-- conformance information 
 
ospfv3Groups      OBJECT IDENTIFIER ::= { ospfv3Conformance 1 } 
ospfv3Compliances OBJECT IDENTIFIER ::= { ospfv3Conformance 2 } 
 
-- compliance statements 
 
ospfv3Compliance MODULE-COMPLIANCE 
        STATUS          current 
        DESCRIPTION     "The compliance statement " 
        MODULE          -- this module 
        MANDATORY-GROUPS { 
                        ospfv3BasicGroup, 
                        ospfv3AreaGroup, 
                        ospfv3IfGroup, 
                        ospfv3VirtIfGroup, 
                        ospfv3NbrGroup, 
                        ospfv3NbmaNbrGroup, 
                        ospfv3VirtNbrGroup, 
                        ospfv3AreaAggregateGroup 
                        } 
 
        GROUP           ospfv3AsLsdbGroup 
        DESCRIPTION 
            "This group is required for OSPFv3 systems that 
            display their AS-scope link state database." 
 
        GROUP           ospfv3AreaLsdbGroup 
        DESCRIPTION 
            "This group is required for OSPFv3 systems that 
            display their Area-scope link state database." 
 
        GROUP           ospfv3LinkLsdbGroup 
        DESCRIPTION 
            "This group is required for OSPFv3 systems that 
            display their Link-scope link state database." 
 
        GROUP           ospfv3HostGroup 
        DESCRIPTION 
            "This group is required for OSPFv3 systems that 
            support attached hosts." 
 
        OBJECT          ospfv3NbrAddressType 
        SYNTAX          InetAddressType { ipv6(2) } 
        DESCRIPTION 
            "An implementation is only required to support IPv6 
            address without zone index." 
 
        OBJECT          ospfv3VirtNbrAddressType 
        SYNTAX          InetAddressType { ipv6(2) } 
        DESCRIPTION 
            "An implementation is only required to support IPv6 
            address without zone index." 
 
        ::= { ospfv3Compliances 1 } 
 
-- units of conformance 
 
ospfv3BasicGroup OBJECT-GROUP 
        OBJECTS         { 
                        ospfv3RouterId, 
                        ospfv3AdminStat, 
                        ospfv3VersionNumber, 
                        ospfv3AreaBdrRtrStatus, 
                        ospfv3ASBdrRtrStatus, 
                        ospfv3AsScopeLsaCount, 
                        ospfv3AsScopeLsaCksumSum, 
                        ospfv3OriginateNewLsas, 
                        ospfv3RxNewLsas, 
                        ospfv3ExtLsaCount, 
                        ospfv3ExtAreaLsdbLimit, 
                        ospfv3MulticastExtensions, 
                        ospfv3ExitOverflowInterval, 
                        ospfv3DemandExtensions, 
                        ospfv3TrafficEngineeringSupport, 
                        ospfv3ReferenceBandwidth, 
                        ospfv3RestartSupport, 
                        ospfv3RestartInterval, 
                        ospfv3RestartStatus, 
                        ospfv3RestartAge, 
                        ospfv3RestartExitReason 
                        } 
        STATUS          current 
        DESCRIPTION 
            "These objects are required for OSPFv3 systems." 
        ::= { ospfv3Groups 1 } 
 
 
ospfv3AreaGroup OBJECT-GROUP 
        OBJECTS         {                       
                        ospfv3ImportAsExtern, 
                        ospfv3AreaSpfRuns, 
                        ospfv3AreaBdrRtrCount, 
                        ospfv3AreaAsBdrRtrCount, 
                        ospfv3AreaScopeLsaCount, 
                        ospfv3AreaScopeLsaCksumSum, 
                        ospfv3AreaSummary, 
                        ospfv3AreaStatus, 
                        ospfv3StubMetric, 
                        ospfv3AreaNssaTranslatorRole, 
                        ospfv3AreaNssaTranslatorState, 
                        ospfv3AreaNssaTranslatorStabilityInterval, 
                        ospfv3AreaNssaTranslatorEvents, 
                        ospfv3AreaStubMetricType 
                        } 
        STATUS          current 
        DESCRIPTION 
            "These objects are required for OSPFv3 systems 
            supporting areas." 
        ::= { ospfv3Groups 2 } 
 
ospfv3AsLsdbGroup OBJECT-GROUP 
        OBJECTS         { 
                        ospfv3AsLsdbSequence, 
                        ospfv3AsLsdbAge, 
                        ospfv3AsLsdbChecksum, 
                        ospfv3AsLsdbAdvertisement, 
                        ospfv3AsLsdbTypeKnown 
                        } 
        STATUS          current 
        DESCRIPTION 
            "These objects are required for OSPFv3 systems 
            that display their AS-scope link state database." 
        ::= { ospfv3Groups 3 } 
 
ospfv3AreaLsdbGroup OBJECT-GROUP 
        OBJECTS         { 
                        ospfv3AreaLsdbSequence, 
                        ospfv3AreaLsdbAge, 
                        ospfv3AreaLsdbChecksum, 
                        ospfv3AreaLsdbAdvertisement, 
                        ospfv3AreaLsdbTypeKnown 
                        } 
        STATUS          current 
        DESCRIPTION 
            "These objects are required for OSPFv3 systems 
            that display their Area-scope link state database." 
        ::= { ospfv3Groups 4 } 
 
ospfv3LinkLsdbGroup OBJECT-GROUP 
        OBJECTS         { 
                        ospfv3LinkLsdbSequence, 
                        ospfv3LinkLsdbAge, 
                        ospfv3LinkLsdbChecksum, 
                        ospfv3LinkLsdbAdvertisement, 
                        ospfv3LinkLsdbTypeKnown 
                        } 
        STATUS          current 
        DESCRIPTION 
            "These objects are required for OSPFv3  systems 
            that display their Link-scope link state database." 
        ::= { ospfv3Groups 5 } 
 
ospfv3HostGroup OBJECT-GROUP 
        OBJECTS         { 
                        ospfv3HostMetric, 
                        ospfv3HostStatus, 
                        ospfv3HostAreaID 
                        } 
        STATUS          current 
        DESCRIPTION 
            "These objects are required  for  OSPFv3  systems 
            that support attached hosts." 
        ::= { ospfv3Groups 6 } 
 
ospfv3IfGroup OBJECT-GROUP 
        OBJECTS         { 
                        ospfv3IfAreaId, 
                        ospfv3IfType, 
                        ospfv3IfAdminStat, 
                        ospfv3IfRtrPriority, 
                        ospfv3IfTransitDelay, 
                        ospfv3IfRetransInterval, 
                        ospfv3IfHelloInterval, 
                        ospfv3IfRtrDeadInterval, 
                        ospfv3IfPollInterval, 
                        ospfv3IfState, 
                        ospfv3IfDesignatedRouter, 
                        ospfv3IfBackupDesignatedRouter, 
                        ospfv3IfEvents, 
                        ospfv3IfStatus, 
                        ospfv3IfMulticastForwarding, 
                        ospfv3IfDemand, 
                        ospfv3IfMetricValue, 
                        ospfv3IfLinkScopeLsaCount, 
                        ospfv3IfLinkLsaCksumSum, 
                        ospfv3IfInstId, 
                        ospfv3IfDemandNbrProbe, 
                        ospfv3IfDemandNbrProbeRetxLimit,  
                        ospfv3IfDemandNbrProbeInterval  
                        } 
        STATUS          current 
        DESCRIPTION 
            "These interface objects are required for  
            OSPFv3 systems." 
        ::= { ospfv3Groups 7 } 
 
ospfv3VirtIfGroup OBJECT-GROUP 
        OBJECTS         { 
                        ospfv3VirtIfIndex, 
                        ospfv3VirtIfTransitDelay, 
                        ospfv3VirtIfRetransInterval, 
                        ospfv3VirtIfHelloInterval, 
                        ospfv3VirtIfRtrDeadInterval, 
                        ospfv3VirtIfState, 
                        ospfv3VirtIfEvents, 
                        ospfv3VirtIfStatus, 
                        ospfv3VirtIfLinkScopeLsaCount, 
                        ospfv3VirtIfLinkLsaCksumSum  
                        } 
        STATUS          current 
        DESCRIPTION 
            "These virtual interface objects are required for  
            OSPFv3 systems." 
        ::= { ospfv3Groups 8 } 
 
ospfv3NbrGroup OBJECT-GROUP 
        OBJECTS         { 
                        ospfv3NbrAddressType, 
                        ospfv3NbrAddress, 
                        ospfv3NbrOptions, 
                        ospfv3NbrPriority, 
                        ospfv3NbrState, 
                        ospfv3NbrEvents, 
                        ospfv3NbrLsRetransQLen, 
                        ospfv3NbrHelloSuppressed, 
                        ospfv3NbrIfId, 
                        ospfv3NbrRestartHelperStatus,  
                        ospfv3NbrRestartHelperAge,  
                        ospfv3NbrRestartHelperExitReason 
                        } 
        STATUS          current 
        DESCRIPTION 
            "These neighbor objects are required for 
            OSPFv3 systems." 
        ::= { ospfv3Groups 9 } 
 
ospfv3NbmaNbrGroup OBJECT-GROUP 
        OBJECTS         { 
                        ospfv3NbmaNbrPriority, 
                        ospfv3NbmaNbrRtrId, 
                        ospfv3NbmaNbrState, 
                        ospfv3NbmaNbrStorageType, 
                        ospfv3NbmaNbrStatus 
                        } 
        STATUS          current 
        DESCRIPTION 
            "These NBMA neighbor objects are required for 
            OSPFv3 systems." 
        ::= { ospfv3Groups 10 } 
 
ospfv3VirtNbrGroup OBJECT-GROUP 
        OBJECTS         { 
                        ospfv3VirtNbrIfIndex, 
                        ospfv3VirtNbrAddressType,  
                        ospfv3VirtNbrAddress, 
                        ospfv3VirtNbrOptions, 
                        ospfv3VirtNbrState, 
                        ospfv3VirtNbrEvents, 
                        ospfv3VirtNbrLsRetransQLen, 
                        ospfv3VirtNbrHelloSuppressed, 
                        ospfv3VirtNbrIfId, 
                        ospfv3VirtNbrRestartHelperStatus,  
                        ospfv3VirtNbrRestartHelperAge,  
                        ospfv3VirtNbrRestartHelperExitReason 
                        } 
        STATUS          current 
        DESCRIPTION 
            "These virtual neighbor objects are required for 
            OSPFv3 systems." 
        ::= { ospfv3Groups 11 } 
 
ospfv3AreaAggregateGroup OBJECT-GROUP 
        OBJECTS         { 
                        ospfv3AreaAggregateStatus, 
                        ospfv3AreaAggregateEffect, 
                        ospfv3AreaAggregateRouteTag 
                        } 
        STATUS          current 
        DESCRIPTION 
            "These area aggregate objects are required for 
            OSPFv3 systems." 
        ::= { ospfv3Groups 12 } 
 
END