2004-11-15 Paul Jakma <paul@dishone.st>
* routeserver.texi: Strip ctrl-M from line endings, note by
sigma@smx.pair.com
diff --git a/doc/routeserver.texi b/doc/routeserver.texi
index 96de1de..4b937c4 100644
--- a/doc/routeserver.texi
+++ b/doc/routeserver.texi
@@ -1,554 +1,554 @@
-@c -*-texinfo-*-
-@c @value{COPYRIGHT_STR}
-@c See file quagga.texi for copying conditions.
-@c
-@c This file is a modified version of Jose Luis Rubio's TeX sources
-@c of his RS-Manual document
-
-@node Configuring Quagga as a Route Server
-@chapter Configuring Quagga as a Route Server
-
-The purpose of a Route Server is to centralize the peerings between BGP
-speakers. For example if we have an exchange point scenario with four BGP
-speakers, each of which maintaining a BGP peering with the other three
-(@pxref{fig:full-mesh}), we can convert it into a centralized scenario where
-each of the four establishes a single BGP peering against the Route Server
-(@pxref{fig:route-server}).
-
-We will first describe briefly the Route Server model implemented by Quagga.
-We will explain the commands that have been added for configuring that
-model. And finally we will show a full example of Quagga configured as Route
-Server.
-
-@menu
-* Description of the Route Server model::
-* Commands for configuring a Route Server::
-* Example of Route Server Configuration::
-@end menu
-
-@node Description of the Route Server model
-@section Description of the Route Server model
-
-First we are going to describe the normal processing that BGP announcements
-suffer inside a standard BGP speaker, as shown in @ref{fig:normal-processing},
-it consists of three steps:
-
-@itemize
-@item When an announcement is received from some peer, the `In' filters
-configured for that peer are applied to the announcement. These filters can
-reject the announcement, accept it unmodified, or accept it with some of its
-attributes modified.
-
-@item The announcements that pass the `In' filters go into the
-Best Path Selection process, where they are compared to other
-announcements referred to the same destination that have been
-received from different peers (in case such other
-announcements exist). For each different destination, the announcement
-which is selected as the best is inserted into the BGP speaker's Loc-RIB.
-
-@item The routes which are inserted in the Loc-RIB are
-considered for announcement to all the peers (except the one
-from which the route came). This is done by passing the routes
-in the Loc-RIB through the `Out' filters corresponding to each
-peer. These filters can reject the route,
-accept it unmodified, or accept it with some of its attributes
-modified. Those routes which are accepted by the `Out' filters
-of a peer are announced to that peer.
-@end itemize
-
-@float Figure,fig:normal-processing
-@image{fig-normal-processing,500pt,,Normal announcement processing,eps}
-@caption{Announcement processing inside a ``normal'' BGP speaker}
-@end float
-
-@float Figure,fig:full-mesh
-@image{fig_topologies_full,,,Full Mesh BGP Topology,eps}
-@caption{Full Mesh}
-@end float
-
-@float Figure,fig:route-server
-@image{fig_topologies_rs,,,Route Server BGP Topology,eps}
-@caption{Route Server and clients}
-@end float
-
-Of course we want that the routing tables obtained in each of the routers
-are the same when using the route server than when not. But as a consequence
-of having a single BGP peering (against the route server), the BGP speakers
-can no longer distinguish from/to which peer each announce comes/goes.
-@anchor{filter-delegation}This means that the routers connected to the route
-server are not able to apply by themselves the same input/output filters
-as in the full mesh scenario, so they have to delegate those functions to
-the route server.
-
-Even more, the ``best path'' selection must be also performed inside the route
-server on behalf of its clients. The reason is that if, after applying the
-filters of the announcer and the (potential) receiver, the route server
-decides to send to some client two or more different announcements referred
-to the same destination, the client will only retain the last one,
-considering it as an implicit withdrawal of the previous announcements for
-the same destination. This is the expected behavior of a BGP speaker as
-defined in @cite{RFC1771}, and even though there are some proposals of
-mechanisms that permit multiple paths for the same destination to be sent
-through a single BGP peering, none of them are currently supported by most
-of the existing BGP implementations.
-
-As a consequence a route server must maintain additional information and
-perform additional tasks for a RS-client that those necessary for common BGP
-peerings. Essentially a route server must:
-
-@anchor{Route Server tasks}
-@itemize
-@item Maintain a separated Routing Information Base (Loc-RIB)
-for each peer configured as RS-client, containing the routes
-selected as a result of the ``Best Path Selection'' process
-that is performed on behalf of that RS-client.
-
-@item Whenever it receives an announcement from a RS-client,
-it must consider it for the Loc-RIBs of the other RS-clients.
-
-@anchor{Route-server path filter process}
-@itemize
-@item
-This means that for each of them the route server must pass the
-announcement through the appropriate `Out' filter of the
-announcer.
-
-@item
-Then through the appropriate `In' filter of
-the potential receiver.
-
-@item
-Only if the announcement is accepted by both filters it will be passed
-to the ``Best Path Selection'' process.
-
-@item
-Finally, it might go into the Loc-RIB of the receiver.
-@end itemize
-@c end of route-server best path process list
-@end itemize
-@c end of route-server tasks list
-
-When we talk about the ``appropriate'' filter, both the announcer and the
-receiver of the route must be taken into account. Suppose that the route
-server receives an announcement from client A, and the route server is
-considering it for the Loc-RIB of client B. The filters that should be
-applied are the same that would be used in the full mesh scenario, i.e.,
-first the `Out' filter of router A for announcements going to router B, and
-then the `In' filter of router B for announcements coming from router A.
-
-We call ``Export Policy'' of a RS-client to the set of `Out' filters that
-the client would use if there was no route server. The same applies for the
-``Import Policy'' of a RS-client and the set of `In' filters of the client
-if there was no route server.
-
-It is also common to demand from a route server that it does not
-modify some BGP attributes (next-hop, as-path and MED) that are usually
-modified by standard BGP speakers before announcing a route.
-
-The announcement processing model implemented by Quagga is shown in
-@ref{fig:rs-processing}. The figure shows a mixture of RS-clients (B, C and D)
-with normal BGP peers (A). There are some details that worth additional
-comments:
-
-@itemize
-@item Announcements coming from a normal BGP peer are also
-considered for the Loc-RIBs of all the RS-clients. But
-logically they do not pass through any export policy.
-
-@item Those peers that are configured as RS-clients do not
-receive any announce from the `Main' Loc-RIB.
-
-@item Apart from import and export policies,
-`In' and `Out' filters can also be set for RS-clients. `In'
-filters might be useful when the route server has also normal
-BGP peers. On the other hand, `Out' filters for RS-clients are
-probably unnecessary, but we decided not to remove them as
-they do not hurt anybody (they can always be left empty).
-@end itemize
-
-@float Figure,fig:rs-processing
-@image{fig-rs-processing,500pt,,,eps}
-@caption{Announcement processing model implemented by the Route Server}
-@end float
-
-@node Commands for configuring a Route Server
-@section Commands for configuring a Route Server
-
-Now we will describe the commands that have been added to quagga
-in order to support the route server features.
-
-@deffn {Route-Server} {neighbor @var{peer-group} route-server-client} {}
-@deffnx {Route-Server} {neighbor @var{A.B.C.D} route-server-client} {}
-@deffnx {Route-Server} {neighbor @var{X:X::X:X} route-server-client} {}
-This command configures the peer given by @var{peer}, @var{A.B.C.D} or
-@var{X:X::X:X} as an RS-client.
-
-Actually this command is not new, it already existed in standard Quagga. It
-enables the transparent mode for the specified peer. This means that some
-BGP attributes (as-path, next-hop and MED) of the routes announced to that
-peer are not modified.
-
-With the route server patch, this command, apart from setting the
-transparent mode, creates a new Loc-RIB dedicated to the specified peer
-(those named `Loc-RIB for X' in @ref{fig:rs-processing}.). Starting from
-that moment, every announcement received by the route server will be also
-considered for the new Loc-RIB.
-@end deffn
-
-@deffn {Route-Server} {neigbor @{A.B.C.D|X.X::X.X|peer-group@} route-map WORD @{import|export@}} {}
-This set of commands can be used to specify the route-map that
-represents the Import or Export policy of a peer which is
-configured as a RS-client (with the previous command).
-@end deffn
-
-@deffn {Route-Server} {match peer @{A.B.C.D|X:X::X:X@}} {}
-This is a new @emph{match} statement for use in route-maps, enabling them to
-describe import/export policies. As we said before, an import/export policy
-represents a set of input/output filters of the RS-client. This statement
-makes possible that a single route-map represents the full set of filters
-that a BGP speaker would use for its different peers in a non-RS scenario.
-
-The @emph{match peer} statement has different semantics whether it is used
-inside an import or an export route-map. In the first case the statement
-matches if the address of the peer who sends the announce is the same that
-the address specified by @{A.B.C.D|X:X::X:X@}. For export route-maps it
-matches when @{A.B.C.D|X:X::X:X@} is the address of the RS-Client into whose
-Loc-RIB the announce is going to be inserted (how the same export policy is
-applied before different Loc-RIBs is shown in @ref{fig:rs-processing}.).
-@end deffn
-
-@deffn {Route-map Command} {call @var{WORD}} {}
-This command (also used inside a route-map) jumps into a different
-route-map, whose name is specified by @var{WORD}. When the called
-route-map finishes, depending on its result the original route-map
-continues or not. Apart from being useful for making import/export
-route-maps easier to write, this command can also be used inside
-any normal (in or out) route-map.
-@end deffn
-
-@node Example of Route Server Configuration
-@section Example of Route Server Configuration
-
-Finally we are going to show how to configure a Quagga daemon to act as a
-Route Server. For this purpose we are going to present a scenario without
-route server, and then we will show how to use the configurations of the BGP
-routers to generate the configuration of the route server.
-
-All the configuration files shown in this section have been taken
-from scenarios which were tested using the VNUML tool
-@uref{http://www.dit.upm.es/vnuml,VNUML}.
-
-@menu
-* Configuration of the BGP routers without Route Server::
-* Configuration of the BGP routers with Route Server::
-* Configuration of the Route Server itself::
-* Further considerations about Import and Export route-maps::
-@end menu
-
-@node Configuration of the BGP routers without Route Server
-@subsection Configuration of the BGP routers without Route Server
-
-We will suppose that our initial scenario is an exchange point with three
-BGP capable routers, named RA, RB and RC. Each of the BGP speakers generates
-some routes (with the @var{network} command), and establishes BGP peerings
-against the other two routers. These peerings have In and Out route-maps
-configured, named like ``PEER-X-IN'' or ``PEER-X-OUT''. For example the
-configuration file for router RA could be the following:
-
-@example
-#Configuration for router 'RA'
-!
-hostname RA
-password ****
-!
-router bgp 65001
- no bgp default ipv4-unicast
- neighbor 2001:0DB8::B remote-as 65002
- neighbor 2001:0DB8::C remote-as 65003
-!
- address-family ipv6
- network 2001:0DB8:AAAA:1::/64
- network 2001:0DB8:AAAA:2::/64
- network 2001:0DB8:0000:1::/64
- network 2001:0DB8:0000:2::/64
-
- neighbor 2001:0DB8::B activate
- neighbor 2001:0DB8::B soft-reconfiguration inbound
- neighbor 2001:0DB8::B route-map PEER-B-IN in
- neighbor 2001:0DB8::B route-map PEER-B-OUT out
-
- neighbor 2001:0DB8::C activate
- neighbor 2001:0DB8::C soft-reconfiguration inbound
- neighbor 2001:0DB8::C route-map PEER-C-IN in
- neighbor 2001:0DB8::C route-map PEER-C-OUT out
- exit-address-family
-!
-ipv6 prefix-list COMMON-PREFIXES seq 5 permit 2001:0DB8:0000::/48 ge 64 le 64
-ipv6 prefix-list COMMON-PREFIXES seq 10 deny any
-!
-ipv6 prefix-list PEER-A-PREFIXES seq 5 permit 2001:0DB8:AAAA::/48 ge 64 le 64
-ipv6 prefix-list PEER-A-PREFIXES seq 10 deny any
-!
-ipv6 prefix-list PEER-B-PREFIXES seq 5 permit 2001:0DB8:BBBB::/48 ge 64 le 64
-ipv6 prefix-list PEER-B-PREFIXES seq 10 deny any
-!
-ipv6 prefix-list PEER-C-PREFIXES seq 5 permit 2001:0DB8:CCCC::/48 ge 64 le 64
-ipv6 prefix-list PEER-C-PREFIXES seq 10 deny any
-!
-route-map PEER-B-IN permit 10
- match ipv6 address prefix-list COMMON-PREFIXES
- set metric 100
-route-map PEER-B-IN permit 20
- match ipv6 address prefix-list PEER-B-PREFIXES
- set community 65001:11111
-!
-route-map PEER-C-IN permit 10
- match ipv6 address prefix-list COMMON-PREFIXES
- set metric 200
-route-map PEER-C-IN permit 20
- match ipv6 address prefix-list PEER-C-PREFIXES
- set community 65001:22222
-!
-route-map PEER-B-OUT permit 10
- match ipv6 address prefix-list PEER-A-PREFIXES
-!
-route-map PEER-C-OUT permit 10
- match ipv6 address prefix-list PEER-A-PREFIXES
-!
-line vty
-!
-@end example
-
-@node Configuration of the BGP routers with Route Server
-@subsection Configuration of the BGP routers with Route Server
-
-To convert the initial scenario into one with route server, first we must
-modify the configuration of routers RA, RB and RC. Now they must not peer
-between them, but only with the route server. For example, RA's
-configuration would turn into:
-
-@example
-# Configuration for router 'RA'
-!
-hostname RA
-password ****
-!
-router bgp 65001
- no bgp default ipv4-unicast
- neighbor 2001:0DB8::FFFF remote-as 65000
-!
- address-family ipv6
- network 2001:0DB8:AAAA:1::/64
- network 2001:0DB8:AAAA:2::/64
- network 2001:0DB8:0000:1::/64
- network 2001:0DB8:0000:2::/64
-
- neighbor 2001:0DB8::FFFF activate
- neighbor 2001:0DB8::FFFF soft-reconfiguration inbound
- exit-address-family
-!
-line vty
-!
-@end example
-
-Which is logically much simpler than its initial configuration, as it now
-maintains only one BGP peering and all the filters (route-maps) have
-disappeared.
-
-@node Configuration of the Route Server itself
-@subsection Configuration of the Route Server itself
-
-As we said when we described the functions of a route server
-(@pxref{Description of the Route Server model}), it is in charge of all the
-route filtering. To achieve that, the In and Out filters from the RA, RB and
-RC configurations must be converted into Import and Export policies in the
-route server.
-
-This is a fragment of the route server configuration (we only show
-the policies for client RA):
-
-@example
-# Configuration for Route Server ('RS')
-!
-hostname RS
-password ix
-!
-bgp multiple-instance
-!
-router bgp 65000 view RS
- no bgp default ipv4-unicast
- neighbor 2001:0DB8::A remote-as 65001
- neighbor 2001:0DB8::B remote-as 65002
- neighbor 2001:0DB8::C remote-as 65003
-!
- address-family ipv6
- neighbor 2001:0DB8::A activate
- neighbor 2001:0DB8::A route-server-client
- neighbor 2001:0DB8::A route-map RSCLIENT-A-IMPORT import
- neighbor 2001:0DB8::A route-map RSCLIENT-A-EXPORT export
- neighbor 2001:0DB8::A soft-reconfiguration inbound
-
- neighbor 2001:0DB8::B activate
- neighbor 2001:0DB8::B route-server-client
- neighbor 2001:0DB8::B route-map RSCLIENT-B-IMPORT import
- neighbor 2001:0DB8::B route-map RSCLIENT-B-EXPORT export
- neighbor 2001:0DB8::B soft-reconfiguration inbound
-
- neighbor 2001:0DB8::C activate
- neighbor 2001:0DB8::C route-server-client
- neighbor 2001:0DB8::C route-map RSCLIENT-C-IMPORT import
- neighbor 2001:0DB8::C route-map RSCLIENT-C-EXPORT export
- neighbor 2001:0DB8::C soft-reconfiguration inbound
- exit-address-family
-!
-ipv6 prefix-list COMMON-PREFIXES seq 5 permit 2001:0DB8:0000::/48 ge 64 le 64
-ipv6 prefix-list COMMON-PREFIXES seq 10 deny any
-!
-ipv6 prefix-list PEER-A-PREFIXES seq 5 permit 2001:0DB8:AAAA::/48 ge 64 le 64
-ipv6 prefix-list PEER-A-PREFIXES seq 10 deny any
-!
-ipv6 prefix-list PEER-B-PREFIXES seq 5 permit 2001:0DB8:BBBB::/48 ge 64 le 64
-ipv6 prefix-list PEER-B-PREFIXES seq 10 deny any
-!
-ipv6 prefix-list PEER-C-PREFIXES seq 5 permit 2001:0DB8:CCCC::/48 ge 64 le 64
-ipv6 prefix-list PEER-C-PREFIXES seq 10 deny any
-!
-route-map RSCLIENT-A-IMPORT permit 10
- match peer 2001:0DB8::B
- call A-IMPORT-FROM-B
-route-map RSCLIENT-A-IMPORT permit 20
- match peer 2001:0DB8::C
- call A-IMPORT-FROM-C
-!
-route-map A-IMPORT-FROM-B permit 10
- match ipv6 address prefix-list COMMON-PREFIXES
- set metric 100
-route-map A-IMPORT-FROM-B permit 20
- match ipv6 address prefix-list PEER-B-PREFIXES
- set community 65001:11111
-!
-route-map A-IMPORT-FROM-C permit 10
- match ipv6 address prefix-list COMMON-PREFIXES
- set metric 200
-route-map A-IMPORT-FROM-C permit 20
- match ipv6 address prefix-list PEER-C-PREFIXES
- set community 65001:22222
-!
-route-map RSCLIENT-A-EXPORT permit 10
- match peer 2001:0DB8::B
- match ipv6 address prefix-list PEER-A-PREFIXES
-route-map RSCLIENT-A-EXPORT permit 20
- match peer 2001:0DB8::C
- match ipv6 address prefix-list PEER-A-PREFIXES
-!
-...
-...
-...
-@end example
-
-If you compare the initial configuration of RA with the route server
-configuration above, you can see how easy it is to generate the Import and
-Export policies for RA from the In and Out route-maps of RA's original
-configuration.
-
-When there was no route server, RA maintained two peerings, one with RB and
-another with RC. Each of this peerings had an In route-map configured. To
-build the Import route-map for client RA in the route server, simply add
-route-map entries following this scheme:
-
-@example
-route-map <NAME> permit 10
- match peer <Peer Address>
- call <In Route-Map for this Peer>
-route-map <NAME> permit 20
- match peer <Another Peer Address>
- call <In Route-Map for this Peer>
-@end example
-
-This is exactly the process that has been followed to generate the route-map
-RSCLIENT-A-IMPORT. The route-maps that are called inside it (A-IMPORT-FROM-B
-and A-IMPORT-FROM-C) are exactly the same than the In route-maps from the
-original configuration of RA (PEER-B-IN and PEER-C-IN), only the name is
-different.
-
-The same could have been done to create the Export policy for RA (route-map
-RSCLIENT-A-EXPORT), but in this case the original Out route-maps where so
-simple that we decided not to use the @var{call WORD} commands, and we
-integrated all in a single route-map (RSCLIENT-A-EXPORT).
-
-The Import and Export policies for RB and RC are not shown, but
-the process would be identical.
-
-@node Further considerations about Import and Export route-maps
-@subsection Further considerations about Import and Export route-maps
-
-The current version of the route server patch only allows to specify a
-route-map for import and export policies, while in a standard BGP speaker
-apart from route-maps there are other tools for performing input and output
-filtering (access-lists, community-lists, ...). But this does not represent
-any limitation, as all kinds of filters can be included in import/export
-route-maps. For example suppose that in the non-route-server scenario peer
-RA had the following filters configured for input from peer B:
-
-@example
- neighbor 2001:0DB8::B prefix-list LIST-1 in
- neighbor 2001:0DB8::B filter-list LIST-2 in
- neighbor 2001:0DB8::B route-map PEER-B-IN in
- ...
- ...
-route-map PEER-B-IN permit 10
- match ipv6 address prefix-list COMMON-PREFIXES
- set local-preference 100
-route-map PEER-B-IN permit 20
- match ipv6 address prefix-list PEER-B-PREFIXES
- set community 65001:11111
-@end example
-
-It is posible to write a single route-map which is equivalent to
-the three filters (the community-list, the prefix-list and the
-route-map). That route-map can then be used inside the Import
-policy in the route server. Lets see how to do it:
-
-@example
- neighbor 2001:0DB8::A route-map RSCLIENT-A-IMPORT import
- ...
-!
-...
-route-map RSCLIENT-A-IMPORT permit 10
- match peer 2001:0DB8::B
- call A-IMPORT-FROM-B
-...
-...
-!
-route-map A-IMPORT-FROM-B permit 1
- match ipv6 address prefix-list LIST-1
- match as-path LIST-2
- on-match goto 10
-route-map A-IMPORT-FROM-B deny 2
-route-map A-IMPORT-FROM-B permit 10
- match ipv6 address prefix-list COMMON-PREFIXES
- set local-preference 100
-route-map A-IMPORT-FROM-B permit 20
- match ipv6 address prefix-list PEER-B-PREFIXES
- set community 65001:11111
-!
-...
-...
-@end example
-
-The route-map A-IMPORT-FROM-B is equivalent to the three filters
-(LIST-1, LIST-2 and PEER-B-IN). The first entry of route-map
-A-IMPORT-FROM-B (sequence number 1) matches if and only if both
-the prefix-list LIST-1 and the filter-list LIST-2 match. If that
-happens, due to the ``on-match goto 10'' statement the next
-route-map entry to be processed will be number 10, and as of that
-point route-map A-IMPORT-FROM-B is identical to PEER-B-IN. If
-the first entry does not match, `on-match goto 10'' will be
-ignored and the next processed entry will be number 2, which will
-deny the route.
-
-Thus, the result is the same that with the three original filters,
-i.e., if either LIST-1 or LIST-2 rejects the route, it does not
-reach the route-map PEER-B-IN. In case both LIST-1 and LIST-2
-accept the route, it passes to PEER-B-IN, which can reject, accept
-or modify the route.
+@c -*-texinfo-*-
+@c @value{COPYRIGHT_STR}
+@c See file quagga.texi for copying conditions.
+@c
+@c This file is a modified version of Jose Luis Rubio's TeX sources
+@c of his RS-Manual document
+
+@node Configuring Quagga as a Route Server
+@chapter Configuring Quagga as a Route Server
+
+The purpose of a Route Server is to centralize the peerings between BGP
+speakers. For example if we have an exchange point scenario with four BGP
+speakers, each of which maintaining a BGP peering with the other three
+(@pxref{fig:full-mesh}), we can convert it into a centralized scenario where
+each of the four establishes a single BGP peering against the Route Server
+(@pxref{fig:route-server}).
+
+We will first describe briefly the Route Server model implemented by Quagga.
+We will explain the commands that have been added for configuring that
+model. And finally we will show a full example of Quagga configured as Route
+Server.
+
+@menu
+* Description of the Route Server model::
+* Commands for configuring a Route Server::
+* Example of Route Server Configuration::
+@end menu
+
+@node Description of the Route Server model
+@section Description of the Route Server model
+
+First we are going to describe the normal processing that BGP announcements
+suffer inside a standard BGP speaker, as shown in @ref{fig:normal-processing},
+it consists of three steps:
+
+@itemize
+@item When an announcement is received from some peer, the `In' filters
+configured for that peer are applied to the announcement. These filters can
+reject the announcement, accept it unmodified, or accept it with some of its
+attributes modified.
+
+@item The announcements that pass the `In' filters go into the
+Best Path Selection process, where they are compared to other
+announcements referred to the same destination that have been
+received from different peers (in case such other
+announcements exist). For each different destination, the announcement
+which is selected as the best is inserted into the BGP speaker's Loc-RIB.
+
+@item The routes which are inserted in the Loc-RIB are
+considered for announcement to all the peers (except the one
+from which the route came). This is done by passing the routes
+in the Loc-RIB through the `Out' filters corresponding to each
+peer. These filters can reject the route,
+accept it unmodified, or accept it with some of its attributes
+modified. Those routes which are accepted by the `Out' filters
+of a peer are announced to that peer.
+@end itemize
+
+@float Figure,fig:normal-processing
+@image{fig-normal-processing,500pt,,Normal announcement processing,eps}
+@caption{Announcement processing inside a ``normal'' BGP speaker}
+@end float
+
+@float Figure,fig:full-mesh
+@image{fig_topologies_full,,,Full Mesh BGP Topology,eps}
+@caption{Full Mesh}
+@end float
+
+@float Figure,fig:route-server
+@image{fig_topologies_rs,,,Route Server BGP Topology,eps}
+@caption{Route Server and clients}
+@end float
+
+Of course we want that the routing tables obtained in each of the routers
+are the same when using the route server than when not. But as a consequence
+of having a single BGP peering (against the route server), the BGP speakers
+can no longer distinguish from/to which peer each announce comes/goes.
+@anchor{filter-delegation}This means that the routers connected to the route
+server are not able to apply by themselves the same input/output filters
+as in the full mesh scenario, so they have to delegate those functions to
+the route server.
+
+Even more, the ``best path'' selection must be also performed inside the route
+server on behalf of its clients. The reason is that if, after applying the
+filters of the announcer and the (potential) receiver, the route server
+decides to send to some client two or more different announcements referred
+to the same destination, the client will only retain the last one,
+considering it as an implicit withdrawal of the previous announcements for
+the same destination. This is the expected behavior of a BGP speaker as
+defined in @cite{RFC1771}, and even though there are some proposals of
+mechanisms that permit multiple paths for the same destination to be sent
+through a single BGP peering, none of them are currently supported by most
+of the existing BGP implementations.
+
+As a consequence a route server must maintain additional information and
+perform additional tasks for a RS-client that those necessary for common BGP
+peerings. Essentially a route server must:
+
+@anchor{Route Server tasks}
+@itemize
+@item Maintain a separated Routing Information Base (Loc-RIB)
+for each peer configured as RS-client, containing the routes
+selected as a result of the ``Best Path Selection'' process
+that is performed on behalf of that RS-client.
+
+@item Whenever it receives an announcement from a RS-client,
+it must consider it for the Loc-RIBs of the other RS-clients.
+
+@anchor{Route-server path filter process}
+@itemize
+@item
+This means that for each of them the route server must pass the
+announcement through the appropriate `Out' filter of the
+announcer.
+
+@item
+Then through the appropriate `In' filter of
+the potential receiver.
+
+@item
+Only if the announcement is accepted by both filters it will be passed
+to the ``Best Path Selection'' process.
+
+@item
+Finally, it might go into the Loc-RIB of the receiver.
+@end itemize
+@c end of route-server best path process list
+@end itemize
+@c end of route-server tasks list
+
+When we talk about the ``appropriate'' filter, both the announcer and the
+receiver of the route must be taken into account. Suppose that the route
+server receives an announcement from client A, and the route server is
+considering it for the Loc-RIB of client B. The filters that should be
+applied are the same that would be used in the full mesh scenario, i.e.,
+first the `Out' filter of router A for announcements going to router B, and
+then the `In' filter of router B for announcements coming from router A.
+
+We call ``Export Policy'' of a RS-client to the set of `Out' filters that
+the client would use if there was no route server. The same applies for the
+``Import Policy'' of a RS-client and the set of `In' filters of the client
+if there was no route server.
+
+It is also common to demand from a route server that it does not
+modify some BGP attributes (next-hop, as-path and MED) that are usually
+modified by standard BGP speakers before announcing a route.
+
+The announcement processing model implemented by Quagga is shown in
+@ref{fig:rs-processing}. The figure shows a mixture of RS-clients (B, C and D)
+with normal BGP peers (A). There are some details that worth additional
+comments:
+
+@itemize
+@item Announcements coming from a normal BGP peer are also
+considered for the Loc-RIBs of all the RS-clients. But
+logically they do not pass through any export policy.
+
+@item Those peers that are configured as RS-clients do not
+receive any announce from the `Main' Loc-RIB.
+
+@item Apart from import and export policies,
+`In' and `Out' filters can also be set for RS-clients. `In'
+filters might be useful when the route server has also normal
+BGP peers. On the other hand, `Out' filters for RS-clients are
+probably unnecessary, but we decided not to remove them as
+they do not hurt anybody (they can always be left empty).
+@end itemize
+
+@float Figure,fig:rs-processing
+@image{fig-rs-processing,500pt,,,eps}
+@caption{Announcement processing model implemented by the Route Server}
+@end float
+
+@node Commands for configuring a Route Server
+@section Commands for configuring a Route Server
+
+Now we will describe the commands that have been added to quagga
+in order to support the route server features.
+
+@deffn {Route-Server} {neighbor @var{peer-group} route-server-client} {}
+@deffnx {Route-Server} {neighbor @var{A.B.C.D} route-server-client} {}
+@deffnx {Route-Server} {neighbor @var{X:X::X:X} route-server-client} {}
+This command configures the peer given by @var{peer}, @var{A.B.C.D} or
+@var{X:X::X:X} as an RS-client.
+
+Actually this command is not new, it already existed in standard Quagga. It
+enables the transparent mode for the specified peer. This means that some
+BGP attributes (as-path, next-hop and MED) of the routes announced to that
+peer are not modified.
+
+With the route server patch, this command, apart from setting the
+transparent mode, creates a new Loc-RIB dedicated to the specified peer
+(those named `Loc-RIB for X' in @ref{fig:rs-processing}.). Starting from
+that moment, every announcement received by the route server will be also
+considered for the new Loc-RIB.
+@end deffn
+
+@deffn {Route-Server} {neigbor @{A.B.C.D|X.X::X.X|peer-group@} route-map WORD @{import|export@}} {}
+This set of commands can be used to specify the route-map that
+represents the Import or Export policy of a peer which is
+configured as a RS-client (with the previous command).
+@end deffn
+
+@deffn {Route-Server} {match peer @{A.B.C.D|X:X::X:X@}} {}
+This is a new @emph{match} statement for use in route-maps, enabling them to
+describe import/export policies. As we said before, an import/export policy
+represents a set of input/output filters of the RS-client. This statement
+makes possible that a single route-map represents the full set of filters
+that a BGP speaker would use for its different peers in a non-RS scenario.
+
+The @emph{match peer} statement has different semantics whether it is used
+inside an import or an export route-map. In the first case the statement
+matches if the address of the peer who sends the announce is the same that
+the address specified by @{A.B.C.D|X:X::X:X@}. For export route-maps it
+matches when @{A.B.C.D|X:X::X:X@} is the address of the RS-Client into whose
+Loc-RIB the announce is going to be inserted (how the same export policy is
+applied before different Loc-RIBs is shown in @ref{fig:rs-processing}.).
+@end deffn
+
+@deffn {Route-map Command} {call @var{WORD}} {}
+This command (also used inside a route-map) jumps into a different
+route-map, whose name is specified by @var{WORD}. When the called
+route-map finishes, depending on its result the original route-map
+continues or not. Apart from being useful for making import/export
+route-maps easier to write, this command can also be used inside
+any normal (in or out) route-map.
+@end deffn
+
+@node Example of Route Server Configuration
+@section Example of Route Server Configuration
+
+Finally we are going to show how to configure a Quagga daemon to act as a
+Route Server. For this purpose we are going to present a scenario without
+route server, and then we will show how to use the configurations of the BGP
+routers to generate the configuration of the route server.
+
+All the configuration files shown in this section have been taken
+from scenarios which were tested using the VNUML tool
+@uref{http://www.dit.upm.es/vnuml,VNUML}.
+
+@menu
+* Configuration of the BGP routers without Route Server::
+* Configuration of the BGP routers with Route Server::
+* Configuration of the Route Server itself::
+* Further considerations about Import and Export route-maps::
+@end menu
+
+@node Configuration of the BGP routers without Route Server
+@subsection Configuration of the BGP routers without Route Server
+
+We will suppose that our initial scenario is an exchange point with three
+BGP capable routers, named RA, RB and RC. Each of the BGP speakers generates
+some routes (with the @var{network} command), and establishes BGP peerings
+against the other two routers. These peerings have In and Out route-maps
+configured, named like ``PEER-X-IN'' or ``PEER-X-OUT''. For example the
+configuration file for router RA could be the following:
+
+@example
+#Configuration for router 'RA'
+!
+hostname RA
+password ****
+!
+router bgp 65001
+ no bgp default ipv4-unicast
+ neighbor 2001:0DB8::B remote-as 65002
+ neighbor 2001:0DB8::C remote-as 65003
+!
+ address-family ipv6
+ network 2001:0DB8:AAAA:1::/64
+ network 2001:0DB8:AAAA:2::/64
+ network 2001:0DB8:0000:1::/64
+ network 2001:0DB8:0000:2::/64
+
+ neighbor 2001:0DB8::B activate
+ neighbor 2001:0DB8::B soft-reconfiguration inbound
+ neighbor 2001:0DB8::B route-map PEER-B-IN in
+ neighbor 2001:0DB8::B route-map PEER-B-OUT out
+
+ neighbor 2001:0DB8::C activate
+ neighbor 2001:0DB8::C soft-reconfiguration inbound
+ neighbor 2001:0DB8::C route-map PEER-C-IN in
+ neighbor 2001:0DB8::C route-map PEER-C-OUT out
+ exit-address-family
+!
+ipv6 prefix-list COMMON-PREFIXES seq 5 permit 2001:0DB8:0000::/48 ge 64 le 64
+ipv6 prefix-list COMMON-PREFIXES seq 10 deny any
+!
+ipv6 prefix-list PEER-A-PREFIXES seq 5 permit 2001:0DB8:AAAA::/48 ge 64 le 64
+ipv6 prefix-list PEER-A-PREFIXES seq 10 deny any
+!
+ipv6 prefix-list PEER-B-PREFIXES seq 5 permit 2001:0DB8:BBBB::/48 ge 64 le 64
+ipv6 prefix-list PEER-B-PREFIXES seq 10 deny any
+!
+ipv6 prefix-list PEER-C-PREFIXES seq 5 permit 2001:0DB8:CCCC::/48 ge 64 le 64
+ipv6 prefix-list PEER-C-PREFIXES seq 10 deny any
+!
+route-map PEER-B-IN permit 10
+ match ipv6 address prefix-list COMMON-PREFIXES
+ set metric 100
+route-map PEER-B-IN permit 20
+ match ipv6 address prefix-list PEER-B-PREFIXES
+ set community 65001:11111
+!
+route-map PEER-C-IN permit 10
+ match ipv6 address prefix-list COMMON-PREFIXES
+ set metric 200
+route-map PEER-C-IN permit 20
+ match ipv6 address prefix-list PEER-C-PREFIXES
+ set community 65001:22222
+!
+route-map PEER-B-OUT permit 10
+ match ipv6 address prefix-list PEER-A-PREFIXES
+!
+route-map PEER-C-OUT permit 10
+ match ipv6 address prefix-list PEER-A-PREFIXES
+!
+line vty
+!
+@end example
+
+@node Configuration of the BGP routers with Route Server
+@subsection Configuration of the BGP routers with Route Server
+
+To convert the initial scenario into one with route server, first we must
+modify the configuration of routers RA, RB and RC. Now they must not peer
+between them, but only with the route server. For example, RA's
+configuration would turn into:
+
+@example
+# Configuration for router 'RA'
+!
+hostname RA
+password ****
+!
+router bgp 65001
+ no bgp default ipv4-unicast
+ neighbor 2001:0DB8::FFFF remote-as 65000
+!
+ address-family ipv6
+ network 2001:0DB8:AAAA:1::/64
+ network 2001:0DB8:AAAA:2::/64
+ network 2001:0DB8:0000:1::/64
+ network 2001:0DB8:0000:2::/64
+
+ neighbor 2001:0DB8::FFFF activate
+ neighbor 2001:0DB8::FFFF soft-reconfiguration inbound
+ exit-address-family
+!
+line vty
+!
+@end example
+
+Which is logically much simpler than its initial configuration, as it now
+maintains only one BGP peering and all the filters (route-maps) have
+disappeared.
+
+@node Configuration of the Route Server itself
+@subsection Configuration of the Route Server itself
+
+As we said when we described the functions of a route server
+(@pxref{Description of the Route Server model}), it is in charge of all the
+route filtering. To achieve that, the In and Out filters from the RA, RB and
+RC configurations must be converted into Import and Export policies in the
+route server.
+
+This is a fragment of the route server configuration (we only show
+the policies for client RA):
+
+@example
+# Configuration for Route Server ('RS')
+!
+hostname RS
+password ix
+!
+bgp multiple-instance
+!
+router bgp 65000 view RS
+ no bgp default ipv4-unicast
+ neighbor 2001:0DB8::A remote-as 65001
+ neighbor 2001:0DB8::B remote-as 65002
+ neighbor 2001:0DB8::C remote-as 65003
+!
+ address-family ipv6
+ neighbor 2001:0DB8::A activate
+ neighbor 2001:0DB8::A route-server-client
+ neighbor 2001:0DB8::A route-map RSCLIENT-A-IMPORT import
+ neighbor 2001:0DB8::A route-map RSCLIENT-A-EXPORT export
+ neighbor 2001:0DB8::A soft-reconfiguration inbound
+
+ neighbor 2001:0DB8::B activate
+ neighbor 2001:0DB8::B route-server-client
+ neighbor 2001:0DB8::B route-map RSCLIENT-B-IMPORT import
+ neighbor 2001:0DB8::B route-map RSCLIENT-B-EXPORT export
+ neighbor 2001:0DB8::B soft-reconfiguration inbound
+
+ neighbor 2001:0DB8::C activate
+ neighbor 2001:0DB8::C route-server-client
+ neighbor 2001:0DB8::C route-map RSCLIENT-C-IMPORT import
+ neighbor 2001:0DB8::C route-map RSCLIENT-C-EXPORT export
+ neighbor 2001:0DB8::C soft-reconfiguration inbound
+ exit-address-family
+!
+ipv6 prefix-list COMMON-PREFIXES seq 5 permit 2001:0DB8:0000::/48 ge 64 le 64
+ipv6 prefix-list COMMON-PREFIXES seq 10 deny any
+!
+ipv6 prefix-list PEER-A-PREFIXES seq 5 permit 2001:0DB8:AAAA::/48 ge 64 le 64
+ipv6 prefix-list PEER-A-PREFIXES seq 10 deny any
+!
+ipv6 prefix-list PEER-B-PREFIXES seq 5 permit 2001:0DB8:BBBB::/48 ge 64 le 64
+ipv6 prefix-list PEER-B-PREFIXES seq 10 deny any
+!
+ipv6 prefix-list PEER-C-PREFIXES seq 5 permit 2001:0DB8:CCCC::/48 ge 64 le 64
+ipv6 prefix-list PEER-C-PREFIXES seq 10 deny any
+!
+route-map RSCLIENT-A-IMPORT permit 10
+ match peer 2001:0DB8::B
+ call A-IMPORT-FROM-B
+route-map RSCLIENT-A-IMPORT permit 20
+ match peer 2001:0DB8::C
+ call A-IMPORT-FROM-C
+!
+route-map A-IMPORT-FROM-B permit 10
+ match ipv6 address prefix-list COMMON-PREFIXES
+ set metric 100
+route-map A-IMPORT-FROM-B permit 20
+ match ipv6 address prefix-list PEER-B-PREFIXES
+ set community 65001:11111
+!
+route-map A-IMPORT-FROM-C permit 10
+ match ipv6 address prefix-list COMMON-PREFIXES
+ set metric 200
+route-map A-IMPORT-FROM-C permit 20
+ match ipv6 address prefix-list PEER-C-PREFIXES
+ set community 65001:22222
+!
+route-map RSCLIENT-A-EXPORT permit 10
+ match peer 2001:0DB8::B
+ match ipv6 address prefix-list PEER-A-PREFIXES
+route-map RSCLIENT-A-EXPORT permit 20
+ match peer 2001:0DB8::C
+ match ipv6 address prefix-list PEER-A-PREFIXES
+!
+...
+...
+...
+@end example
+
+If you compare the initial configuration of RA with the route server
+configuration above, you can see how easy it is to generate the Import and
+Export policies for RA from the In and Out route-maps of RA's original
+configuration.
+
+When there was no route server, RA maintained two peerings, one with RB and
+another with RC. Each of this peerings had an In route-map configured. To
+build the Import route-map for client RA in the route server, simply add
+route-map entries following this scheme:
+
+@example
+route-map <NAME> permit 10
+ match peer <Peer Address>
+ call <In Route-Map for this Peer>
+route-map <NAME> permit 20
+ match peer <Another Peer Address>
+ call <In Route-Map for this Peer>
+@end example
+
+This is exactly the process that has been followed to generate the route-map
+RSCLIENT-A-IMPORT. The route-maps that are called inside it (A-IMPORT-FROM-B
+and A-IMPORT-FROM-C) are exactly the same than the In route-maps from the
+original configuration of RA (PEER-B-IN and PEER-C-IN), only the name is
+different.
+
+The same could have been done to create the Export policy for RA (route-map
+RSCLIENT-A-EXPORT), but in this case the original Out route-maps where so
+simple that we decided not to use the @var{call WORD} commands, and we
+integrated all in a single route-map (RSCLIENT-A-EXPORT).
+
+The Import and Export policies for RB and RC are not shown, but
+the process would be identical.
+
+@node Further considerations about Import and Export route-maps
+@subsection Further considerations about Import and Export route-maps
+
+The current version of the route server patch only allows to specify a
+route-map for import and export policies, while in a standard BGP speaker
+apart from route-maps there are other tools for performing input and output
+filtering (access-lists, community-lists, ...). But this does not represent
+any limitation, as all kinds of filters can be included in import/export
+route-maps. For example suppose that in the non-route-server scenario peer
+RA had the following filters configured for input from peer B:
+
+@example
+ neighbor 2001:0DB8::B prefix-list LIST-1 in
+ neighbor 2001:0DB8::B filter-list LIST-2 in
+ neighbor 2001:0DB8::B route-map PEER-B-IN in
+ ...
+ ...
+route-map PEER-B-IN permit 10
+ match ipv6 address prefix-list COMMON-PREFIXES
+ set local-preference 100
+route-map PEER-B-IN permit 20
+ match ipv6 address prefix-list PEER-B-PREFIXES
+ set community 65001:11111
+@end example
+
+It is posible to write a single route-map which is equivalent to
+the three filters (the community-list, the prefix-list and the
+route-map). That route-map can then be used inside the Import
+policy in the route server. Lets see how to do it:
+
+@example
+ neighbor 2001:0DB8::A route-map RSCLIENT-A-IMPORT import
+ ...
+!
+...
+route-map RSCLIENT-A-IMPORT permit 10
+ match peer 2001:0DB8::B
+ call A-IMPORT-FROM-B
+...
+...
+!
+route-map A-IMPORT-FROM-B permit 1
+ match ipv6 address prefix-list LIST-1
+ match as-path LIST-2
+ on-match goto 10
+route-map A-IMPORT-FROM-B deny 2
+route-map A-IMPORT-FROM-B permit 10
+ match ipv6 address prefix-list COMMON-PREFIXES
+ set local-preference 100
+route-map A-IMPORT-FROM-B permit 20
+ match ipv6 address prefix-list PEER-B-PREFIXES
+ set community 65001:11111
+!
+...
+...
+@end example
+
+The route-map A-IMPORT-FROM-B is equivalent to the three filters
+(LIST-1, LIST-2 and PEER-B-IN). The first entry of route-map
+A-IMPORT-FROM-B (sequence number 1) matches if and only if both
+the prefix-list LIST-1 and the filter-list LIST-2 match. If that
+happens, due to the ``on-match goto 10'' statement the next
+route-map entry to be processed will be number 10, and as of that
+point route-map A-IMPORT-FROM-B is identical to PEER-B-IN. If
+the first entry does not match, `on-match goto 10'' will be
+ignored and the next processed entry will be number 2, which will
+deny the route.
+
+Thus, the result is the same that with the three original filters,
+i.e., if either LIST-1 or LIST-2 rejects the route, it does not
+reach the route-map PEER-B-IN. In case both LIST-1 and LIST-2
+accept the route, it passes to PEER-B-IN, which can reject, accept
+or modify the route.