diff --git a/configuration/component.rst b/configuration/component.rst
index 7f52ee0..b49f0cc 100644
--- a/configuration/component.rst
+++ b/configuration/component.rst
@@ -1,2 +1,37 @@
 Component Configuration
 =======================
+
+Different from network configurations,
+component configurations are attributes and feature flags specific to ONOS components.
+
+For more details, please read ONOS Wiki `Component Configuration <https://wiki.onosproject.org/display/ONOS/Component+Configuration>`_
+
+Enable/Disable Phased Recovery
+------------------------------
+To check current status:
+
+.. code-block:: console
+
+  onos > cfg get org.onosproject.segmentrouting.phasedrecovery.impl.PhasedRecoveryManager phasedRecovery
+    name=phasedRecovery, type=boolean, value=false, defaultValue=false, description=Enabling phased recovery.
+
+
+We can see that the default value of phased recovery is false.
+Which means it is disabled by default.
+
+To enable phased recovery:
+
+.. code-block:: console
+
+  onos > cfg set org.onosproject.segmentrouting.phasedrecovery.impl.PhasedRecoveryManager phasedRecovery true
+  onos > cfg get org.onosproject.segmentrouting.phasedrecovery.impl.PhasedRecoveryManager phasedRecovery
+    name=phasedRecovery, type=boolean, value=true, defaultValue=false, description=Enabling phased recovery.
+
+Now the value is true and we have successfully enable phased recovery.
+
+To disable phased recovery, change the value to ``false``.
+
+
+.. tip::
+  Simply run ``cfg get`` in ONOS CLI to view all available component configurations supported by ONOS.
+  The default values are fine-tuned for SD-Fabric, and therefore we use them for most of the cases.
diff --git a/configuration/network.rst b/configuration/network.rst
index 6fc4c4e..14efe64 100644
--- a/configuration/network.rst
+++ b/configuration/network.rst
@@ -1,2 +1,397 @@
 Network Configuration
 =====================
+SD-Fabric uses several different types of network configurations.
+We only focus on ``devices`` and ``ports`` configuration in this section.
+With these configured properly, SD-Fabric can provide basic L2/L3 connectivity.
+
+See :ref:`advanced-features` for advanced feature configurations.
+
+Device Configuration
+--------------------
+Each switch in SD-Fabric requires a device config.
+
+.. code-block:: json
+
+    {
+      "devices" : {
+        "device:leaf1" : {
+          "segmentrouting" : {
+            "ipv4NodeSid" : 101,
+            "ipv4Loopback" : "192.168.0.201",
+            "ipv6NodeSid" : 111,
+            "ipv6Loopback" : "2000::c0a8:0201",
+            "routerMac" : "00:00:00:00:02:01",
+            "isEdgeRouter" : true,
+            "adjacencySids" : []
+          },
+          "basic" : {
+            "name": "Leaf1",
+            "managementAddress": "grpc://10.128.100.51:9339?device_id=1",
+            "driver": "stratum-tofino",
+            "pipeconf": "org.stratumproject.fabric-spgw-int.montara_sde_9_5_0"
+          }
+        }
+      }
+    }
+
+- ``device:leaf1``: DPID of the device.
+
+- ``ipv4NodeSid``: IPv4 node segment ID, which is used as an MPLS label in
+  forwarding IPv4 traffic. Can be arbitrary and should be globally unique.
+
+- ``ipv4Loopback``: IPv4 loopback address. Can be arbitrary, should be globally
+  unique and should not be part of the same subnet(s) defined on the data plane
+  ports (see port config).
+
+- ``ipv6NodeSid``: IPv6 node segment ID, which is used as an MPLS label in
+  forwarding IPv6 traffic. Can be arbitrary and should be globally unique. Only
+  required when using IPv6.
+
+- ``ipv6Loopback``: IPv6 loopback address. Can be arbitrary, should be globally
+  unique and should not be part of the same subnet(s) defined on the data plane
+  ports (see port config).  Only required when using IPv6.
+
+- ``routerMac``: Router MAC address. Can be arbitrary and should be globally
+  unique.  This MAC address will be used to reply the ARP request for the
+  loopback IP or the Interface IP that will be introduced later.  (We recommend
+  using the MAC address of the device's management interface as the router
+  MAC.)
+
+- ``isEdgeRouter``: True for leaf switches. False for spine switches.
+
+- ``adjacencySids``: Deprecated.  Just put an empty array for now.
+
+- ``name``: Name of the device. It is an arbitrary name to identify the device easily.
+
+- ``managementAddress``: gRPC endpoint of the Stratum device and a numerical device ID.
+  The IP address can be replaced by domain name as well.
+
+- ``driver``: ``stratum-bmv2`` or ``stratum-tofino``, depending on which switch this is.
+
+- ``pipeconf``: A list of available pipeconfs can be dumped by running ``pipeconfs`` in ONOS CLI.
+  Select the pipeconf you would like to use for this device.
+
+.. caution::
+    We should avoid using reserved MPLS labels for ``ipv4NodeSid`` and
+    ``ipv6NodeSid``.  Please check here for the reserved values:
+    http://www.iana.org/assignments/mpls-label-values/mpls-label-values.xhtml
+
+.. note::
+    Most of the SD-Fabric configurations support dynamic configuration updates.
+    Unfortunately, SD-Fabric currently **do not support dynamic device
+    configuration updates**.  You will have to restart the device when if
+    corresponding device configuration changes.
+
+    Having said that, when introducing a completely new device in the network,
+    the device configurations pushed before the device's connection should
+    apply correctly.
+
+Bridging and Unicast Routing
+----------------------------
+
+.. attention::
+    - VLAN **4094** is reserved for unconfigured ports (e.g. spine facing ports)
+
+Access Ports
+^^^^^^^^^^^^
+
+The necessary but minimum configuration for an access port is simply a VLAN.
+
+.. code-block:: json
+
+    {
+      "ports" : {
+        "of:0000000000000204/12" : {
+          "interfaces" : [{
+            "name" : "serverA-intf",
+            "vlan-untagged": 10
+          }]
+        },
+        "of:0000000000000204/16" : {
+          "interfaces" : [{
+            "name" : "serverB-intf",
+            "vlan-untagged": 10
+          }]
+        }
+      }
+    }
+
+The example above shows two ports (12 and 16) on switch ``of:204`` that have
+been assigned to VLAN 10 using the ``vlan-untagged`` keyword.
+
+It simply means that packets come in and leave out of these switches untagged,
+but internally they are assigned VLAN 10 and they belong to the bridging domain
+defined for VLAN 10.
+
+``name`` is used to associate the interface with a globally unique, user
+friendly name. It can be omitted.
+
+With the configuration shown above, the packets will always be bridged, but
+they cannot be routed out of the VLAN (e.g. to other subnets).  To add the
+capability to route out of VLAN 10, we need to add a subnet/gateway IP (similar
+to `interface-vlans or SVIs in traditional networks
+<https://www.youtube.com/watch?v=bUXpmiJpGb0>`_).
+
+.. code-block:: json
+
+    {
+      "ports" : {
+        "of:0000000000000204/12" : {
+          "interfaces" : [{
+            "name" : "serverA-intf",
+            "ips" : [ "10.0.1.254/24"],
+            "vlan-untagged": 10
+          }]
+        },
+        "of:0000000000000204/16" : {
+          "interfaces" : [{
+            "name" : "serverB-intf",
+            "ips" : [ "10.0.1.254/24"],
+            "vlan-untagged": 10
+          }]
+        }
+      }
+    }
+
+In this example, VLAN 10 is associated with subnet ``10.0.1.0/24``, and the
+gateway IP for hosts in this subnet is ``10.0.1.254/32``.
+
+When the desire is to route out of a VLAN, this assignment is currently
+necessary on all ports configured in the same VLAN.
+
+.. note::
+    Typically we only expect a single subnet for a VLAN. Similar to traditional
+    networks, for us, a subnet == VLAN. Different VLANs should be configured in
+    different subnets.
+
+    In certain use-cases, it may be necessary to configure multiple subnets in
+    the same VLAN. This is possible by adding more subnet/gateway IPs in the
+    ``ips`` array.
+
+.. tip::
+    One subnet cannot be configured on multiple leaf switches.
+
+    We usually configure one subnet for all the ports on the same leaf switch.
+
+Tagged Ports
+^^^^^^^^^^^^
+Tagged port configuration is similar.
+
+.. code-block:: json
+
+    {
+      "ports" : {
+        "of:0000000000000204/24" : {
+          "interfaces" : [{
+            "name" : "serverA-intf",
+            "ips" : [ "10.0.2.254/24", "10.0.4.254/24" ],
+            "vlan-tagged" : [ 20, 40 ]
+          }]
+        }
+      }
+    }
+
+The configuration above for port 24 on switch of:204 shows two VLANs 20 and 40
+configured on that port, with corresponding subnets and gateway IPs.
+
+Note that there is no specific ordering required in the ``ips`` or
+``vlan-tagged`` arrays to correlate the VLANs to their corresponding subnets.
+
+In a future release, we will correlate VLAN and subnets configuration in a more
+readable way.
+
+Native VLAN on Tagged Ports
+^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+An additional configuration ``vlan-native`` possible on tagged ports includes
+the ability to specify a VLAN (and thus a bridging domain) for incoming
+untagged packets.
+
+Typically, such configuration in trunk ports in traditional networks is
+referred to a native VLAN.
+
+.. code-block:: json
+
+    {
+      "ports" : {
+        "of:0000000000000204/24" : {
+          "interfaces" : [ {
+            "name" : "serverA-intf",
+            "ips" : [ "10.0.2.254/24", "10.0.4.254/24", "10.0.1.254/24" ],
+            "vlan-tagged" : [ 20, 40 ],
+            "vlan-native" : 10
+          }]
+        }
+      }
+    }
+
+Note that it is also necessary to configure the subnet/gateway IP corresponding
+to the native VLAN if you wish to route out of that VLAN.
+
+Configuring interface for IPv6
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+It is similar to configure IPv6 routing. Simply replace the addresses in
+``ips`` with IPv6 addresses. For example:
+
+.. code-block:: json
+
+    {
+      "ports" : {
+        "of:0000000000000204/24" : {
+          "interfaces" : [ {
+            "name" : "serverA-intf",
+            "ips" : [ "10.0.2.254/24", "2000::1ff/120" ],
+            "vlan-tagged" : [ 20, 40 ]
+          }]
+        }
+      }
+    }
+
+.. note::
+    There is a known issue that breaks dynamic VLAN configuration.
+    Until the issue get resolved, you need to restart the switch agent to reinstall the flows.
+
+IPv6 Router Advertisement
+^^^^^^^^^^^^^^^^^^^^^^^^^
+
+Router Advertisement overview
+"""""""""""""""""""""""""""""
+
+Router advertisement application is for enabling **Router Advertisement** and
+**Router Solicitation** functionalities supported by IPv6 routers.
+
+More details are available in `RFC 4861 <https://tools.ietf.org/html/rfc4861>`_.
+
+Application identifies which IPv6 interfaces are currently configured in the
+system and it will try to send out **unsolicited Router Advertisement** (RA)
+messages from these interfaces.
+
+Each such RA message will have two mandatory options named **Source link-layer
+address** and **MTU**.
+
+Additional RA option **prefix** can be enabled using component configuration
+**raGlobalPrefixConfStatus**.
+
+Application also processes **Router Solicitations** (RS) sent from hosts. Upon
+receiving RS on a particular interface application stops RA transmission in
+that interface and immediately sends RA targeted to the solicited host. After
+that application continues unsolicited RA transmission on that interface.
+
+Activate and configure RA
+"""""""""""""""""""""""""
+
+RA application can be activated from CLI by running
+
+.. code-block:: console
+
+  onos> app activate routeradvertisement
+
+Behavior of RA application is controlled by ONOS component configuration
+subsystem and following are possible configuration options.
+
+- ``raThreadDelay``: Delay between consecutive RA transmissions
+
+- ``raPoolSize``: Capacity of thread pool to be used for RA transmissions
+
+- ``raFlagMbitStatus``: RA flag “Managed address configuration”
+  enabled/disabled
+
+- ``raFlagObitStatus``: RA flag “Other configuration” enabled/disabled
+
+- ``raOptionPrefixStatus``: RA Option “prefix” is enabled/disabled. Router
+  prefixes will be available in RA only if this flag is “true”
+
+- ``raGlobalPrefixConfStatus``: Enable switch level global prefix
+  configuration.
+  Once ``raGlobalPrefixConfStatus`` is enabled, RA prefix option is generated
+  from port configuration of device, see for more details.
+
+To set the options, following the command (example for ``raOptionPrefixStatus``)
+
+.. code-block:: console
+
+  onos> cfg set org.onosproject.ra.RouterAdvertisementManager raOptionPrefixStatus true
+
+Prefix details are picked up from network interface configuration.
+
+RA app will filter out link-local IPs while preparing prefixes.
+
+For example, in following configuration, Prefix will include only
+**2001:0558:FF10:04C9::2:1ff/120**.
+
+.. code-block:: json
+
+    {
+      "ports": {
+        "of:0000000000000018/16": {
+          "interfaces": [{
+            "ips": [ "192.168.114.1/24", "2001:0558:FF10:04C9::2:1ff/120", "FE80::4EA8:2AFF:FE24:8E5F/120" ],
+            "vlan-untagged": "11",
+            "name": "18-15"
+          }]
+        }
+      }
+    }
+
+Global prefix configuration
+"""""""""""""""""""""""""""
+
+In some cases, users may want to have a set of global prefix **advertised on
+all edge interfaces**.
+
+Such prefixes can be configured in **devices** section of network configuration
+in the following way.
+
+.. code-block:: json
+
+    {
+      "devices": {
+        "of:0000000000000018": {
+          "routeradvertisement" : {
+            "prefixes": [ "2001:0558:FF10:04C9::3:1ff/120"]
+          }
+        }
+      }
+    }
+
+.. note::
+    When global prefix is configured, RA app will ignore any prefixes
+    configured on switch interfaces.
+
+Notes about interface config
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+There is no need to configure ports on switches that are meant to connect to
+other switches.
+
+The VLAN (untagged or tagged) configuration is only meant for ports that are
+connected to hosts (edge ports).
+
+.. image:: ../images/config-vlan.png
+
+Furthermore, note that the same VLAN can be configured on multiple ToRs - e.g.
+VLAN 20 in the figure above.
+
+However this does not mean that the ports are in the same bridging domain,
+because in the fabric, the communication between ToRs is through a routed
+network.
+
+In other words, a host on VLAN 20 (untagged or tagged) connected to one ToR can
+communicate with another host on VLAN 20 (untagged or tagged) connected to a
+different ToR, but the MAC addresses will change as the traffic goes through a
+routed network.
+
+Please do not use this feature to connect switches in unsupported topologies as
+shown in the example below.
+
+The fabric is not designed to be one big Ethernet fabric. The bridging domain
+is restricted to within one ToR.
+
+If the bridging domain is extended across two ToRs directly linked to each
+other, there is a chance of loops.
+
+In other words, the ToRs/Leafs are not standalone 802.1Q bridges, and should
+not be used as such.
+
+.. image:: ../images/config-vlan-invalid.png