#
# $Id: arad.soc,v 1.90 Broadcom SDK $
#
# $Copyright: Copyright 2016 Broadcom Corporation.
# This program is the proprietary software of Broadcom Corporation
# and/or its licensors, and may only be used, duplicated, modified
# or distributed pursuant to the terms and conditions of a separate,
# written license agreement executed between you and Broadcom
# (an "Authorized License").  Except as set forth in an Authorized
# License, Broadcom grants no license (express or implied), right
# to use, or waiver of any kind with respect to the Software, and
# Broadcom expressly reserves all rights in and to the Software
# and all intellectual property rights therein.  IF YOU HAVE
# NO AUTHORIZED LICENSE, THEN YOU HAVE NO RIGHT TO USE THIS SOFTWARE
# IN ANY WAY, AND SHOULD IMMEDIATELY NOTIFY BROADCOM AND DISCONTINUE
# ALL USE OF THE SOFTWARE.  
#  
# Except as expressly set forth in the Authorized License,
#  
# 1.     This program, including its structure, sequence and organization,
# constitutes the valuable trade secrets of Broadcom, and you shall use
# all reasonable efforts to protect the confidentiality thereof,
# and to use this information only in connection with your use of
# Broadcom integrated circuit products.
#  
# 2.     TO THE MAXIMUM EXTENT PERMITTED BY LAW, THE SOFTWARE IS
# PROVIDED "AS IS" AND WITH ALL FAULTS AND BROADCOM MAKES NO PROMISES,
# REPRESENTATIONS OR WARRANTIES, EITHER EXPRESS, IMPLIED, STATUTORY,
# OR OTHERWISE, WITH RESPECT TO THE SOFTWARE.  BROADCOM SPECIFICALLY
# DISCLAIMS ANY AND ALL IMPLIED WARRANTIES OF TITLE, MERCHANTABILITY,
# NONINFRINGEMENT, FITNESS FOR A PARTICULAR PURPOSE, LACK OF VIRUSES,
# ACCURACY OR COMPLETENESS, QUIET ENJOYMENT, QUIET POSSESSION OR
# CORRESPONDENCE TO DESCRIPTION. YOU ASSUME THE ENTIRE RISK ARISING
# OUT OF USE OR PERFORMANCE OF THE SOFTWARE.
# 
# 3.     TO THE MAXIMUM EXTENT PERMITTED BY LAW, IN NO EVENT SHALL
# BROADCOM OR ITS LICENSORS BE LIABLE FOR (i) CONSEQUENTIAL,
# INCIDENTAL, SPECIAL, INDIRECT, OR EXEMPLARY DAMAGES WHATSOEVER
# ARISING OUT OF OR IN ANY WAY RELATING TO YOUR USE OF OR INABILITY
# TO USE THE SOFTWARE EVEN IF BROADCOM HAS BEEN ADVISED OF THE
# POSSIBILITY OF SUCH DAMAGES; OR (ii) ANY AMOUNT IN EXCESS OF
# THE AMOUNT ACTUALLY PAID FOR THE SOFTWARE ITSELF OR USD 1.00,
# WHICHEVER IS GREATER. THESE LIMITATIONS SHALL APPLY NOTWITHSTANDING
# ANY FAILURE OF ESSENTIAL PURPOSE OF ANY LIMITED REMEDY.$
#

# Load DRAM tuning properties from local File. RcLoad will not fail if file not found, and will not show errors of missing file.
set RCError=off
debug appl shell warn
rcload /home/negev/bcm88650_dram_tune.soc
debug appl shell =
set RCError=on

debug info
debug appl rcload warn
debug appl symtab warn
debug bcm rx,tx,link,attach warn
debug soc tests warn
debug soc rx,phy,schan,reg,socmem,dma,mem,miim,mii,intr,counter,ddr warn
debug soc common err
debug sys verinet warn

rcload arad_dram.soc

# Set modid:
# If diag_chassis is enabled (two line cards), and 'slot' is defined (slot is defined only when
# working without a management card) - set modid to be 0 for slot 0, and 2 for slot 2
# Otherwise (single line card, or management card), set modid to be 0 for unit 0, and 2 for unit 2
# If module_id is set, then set modid to have module_id value
if $?diag_chassis && $?slot "\
  local modid $slot" \
else "\
  local modid $unit"
expr $modid==1; if $? "local modid 2"

if $?module_id " \
  local modid $module_id"

echo "$unit: modid=$modid"

# Set base_modid:
# Id base_module_id is set, then set base_modid to have base_module_id value.
# Otherwise, set base_modid to be 0.
if $?base_module_id " \
  local base_modid $base_module_id" \
else " \
  local base_modid 0"

expr $base_modid > 0
if $? " \
  echo '$unit: base_modid=$base_modid'"

# Set nof_devices:
# If diag_chassis is enabled (mgmt card) - set nof_devices to be 2.
# Otherwise, set nof_devices to be 1.
# If n_devices is set, then set nof_devices to have n_devices value.
if $?diag_chassis " \
  local nof_devices 2" \
else "\
  local nof_devices 1"

if $?n_devices " \
  local nof_devices $n_devices"

expr $nof_devices > 1
if $? " \
  echo '$unit: nof_devices=$nof_devices'"

if $?mng_cpu " \
  echo '$unit:management card - polling is set on'; \
  config add polled_irq_mode.BCM88650=1; \
  config add schan_intr_enable.BCM88650=0; \
  config add tdma_intr_enable.BCM88650=0; \
  config add tslam_intr_enable.BCM88650=0; \
  config add miim_intr_enable.BCM88650=0; \
  config add polled_irq_mode.BCM88750=1; \
  config add schan_intr_enable.BCM88750=0; \
  config add tdma_intr_enable.BCM88750=0; \
  config add tslam_intr_enable.BCM88750=0; \
  config add miim_intr_enable.BCM88750=0; "

#default values in a case which these parameters are not exist
if !$?diag_cosq_disable "\
  local diag_cosq_disable 0"
if !$?warmboot "\
  local warmboot 0"
if !$?diag_disable "\
  local diag_disable 0"
if !$?diag_no_appl_stk "\
  local diag_no_appl_stk 0"
if !$?diag_no_itmh_prog_mode "\
  local diag_no_itmh_prog_mode 0"
if !$?l2_mode "\
  local l2_mode 0"

INIT_DNX ModID=$modid BaseModID=$base_modid NofDevices=$nof_devices CosqDisable=$diag_cosq_disable NoAppl=$diag_disable Warmboot=$warmboot NoApplStk=$diag_no_appl_stk NoItmhProgMode=$diag_no_itmh_prog_mode L2Mode=$l2_mode

#LED support section start
local ledcode '02 0D 67 31 67 1C 02 0E 67 31 67 1C 02 0F 67 31\
 67 1C 02 10 67 31 67 1C 86 E0 3A 08 67 37 75 3E\
 28 32 00 32 01 B7 97 75 3E 16 E0 CA 05 70 42 77\
 3E 67 37 75 3E 77 42 12 A0 F8 15 1A 00 57 32 0E\
 87 57 32 0F 87 57' #sdk88650.hex

# Download LED code into LED processor and enable (if applicable).
if $?feature_led_proc && $?ledcode && !$?simulator \
    "led prog $ledcode; \
     led auto on; led start"

# If loading multiple rc.soc, upon loading the last unit, restart
# all LED processors so any common blinking is in sync.
# if !"expr $?feature_led_proc && !$?simulator && $unit == $units - 1" \
#    "*:led stop; *:led start"
#LED support section end

echo "arad.soc: Done."