#
# $Id: qax.soc,v 1.90 2013/08/14 08:32:00 ninash Exp $
#
# $Copyright: (c) 2011 Broadcom Corporation
# All Rights Reserved.$
#

# Load DRAM tuning properties from local File. RcLoad will not fail if file not found, and will not show errors of missing file.
#der 0x40 4
#exit

debug info
debug appl rcload warn
debug appl symtab warn
debug bcm rx,tx,link,attach warn
debug soc tests warn
debug soc rx,phy,schan,reg,socmem,dma,mem,miim,mii,intr,counter,ddr warn
debug soc common err
debug sys verinet warn
debug soc physim warn

if $?QAX \
    'rcload bcm88470_board.soc'

if $?QUX \
    'rcload bcm88270_board.soc'

# Load DRAM tuning properties from local File. RcLoad will not fail if file not found, and will not show errors of missing file.
set RCError=off
debug appl shell warn
if $?QAX \
    'rcload /home/negev/bcm88470_dram_tune.soc'
if $?QUX \
    'rcload /home/negev/bcm88270_dram_tune.soc'

debug appl shell =
set RCError=on

set RCError=off
rcload combo28_dram.soc
set RCError=on

#Set fabric connect mode as FE for multi FAP system
if $?diag_chassis " \
   config add fabric_connect_mode.BCM88470=FE"

# Set modid:
# If diag_chassis is enabled (two line cards), and 'slot' is defined (slot is defined only when
# working without a management card - set modid to be 'slot'
# Otherwise (single line card, or management card), set modid to be 0 for unit 0, and 1 for unit != 0
if $?diag_chassis && $?slot "\
  local modid $slot" \
else "\
  local modid $unit"
expr $modid==1; if $? "local modid 2"

if $?module_id " \
  local modid $module_id"

echo "$unit: modid=$modid"

# Set base_modid:
# Id base_module_id is set, then set base_modid to have base_module_id value.
# Otherwise, set base_modid to be 0.
if $?base_module_id " \
  local base_modid $base_module_id" \
else " \
  local base_modid 0"

expr $base_modid > 0
if $? " \
  echo '$unit: base_modid=$base_modid'"

if $?diag_chassis " \
  local nof_devices 2" \
else "\
  local nof_devices 1"

if $?n_devices " \
  local nof_devices $n_devices"

expr $nof_devices > 1
if $? " \
  echo '$unit: nof_devices=$nof_devices'"

if $?mng_cpu " \
  echo '$unit:management card - polling is set on'; \
  config add polled_irq_mode.BCM88675=1; \
  config add schan_intr_enable.BCM88675=0; \
  config add tdma_intr_enable.BCM88675=0; \
  config add tslam_intr_enable.BCM88675=0; \
  config add miim_intr_enable.BCM88675=0; "

#Counters unavailable in cmodel
if $?cmodel " \
  config add counter_engine_sampling_interval=0;"

#default values in a case which these parameters are not exist
if !$?diag_cosq_disable "\
  local diag_cosq_disable 0"
if !$?warmboot "\
  local warmboot 0"
if !$?diag_disable "\
  local diag_disable 0"
if !$?diag_no_itmh_prog_mode "\
  local diag_no_itmh_prog_mode 0"
if !$?l2_mode "\
  local l2_mode 0"

#Disable interrupts in cmodel
if $?cmodel "\
  local no_intr 1" \
else "\
  local no_intr 0"

if $?QUX "\
    local no_elk 1" \
else "\
    local no_elk 0"

INIT_DNX ModID=$modid NofDevices=$nof_devices CosqDisable=$diag_cosq_disable NoAppl=$diag_disable Warmboot=$warmboot NoRxLos=1 NoLinkscan=0 NoElkDevice=$no_elk NoElkAppl=0 NoItmhProgMode=$diag_no_itmh_prog_mode L2Mode=$l2_mode NoIntr=$no_intr

#echo "performing force forward to sysport 1"
#mod IHP_PINFO_LLR 0 256 DEFAULT_CPU_TRAP_CODE=200 DEFAULT_ACTION_PROFILE_FWD=7
#mod IHB_FWD_ACT_PROFILE 200 1 FWD_ACT_DESTINATION=0x10001 FWD_ACT_DESTINATION_OVERWRITE=1
#echo "performing credit flush from NIF to EGQ"
#m NBIH_TX_EGRESS_CREDITS_DEBUG_PM TX_FLUSH_EGRESS_PORT_0_MLF_0_QMLF_N=1 TX_FLUSH_EGRESS_PORT_0_MLF_1_QMLF_N=1 TX_FLUSH_EGRESS_PORT_0_MLF_2_QMLF_N=1 TX_FLUSH_EGRESS_PORT_0_MLF_3_QMLF_N=1
echo "qax.soc: Done."