diff --git a/Makefile b/Makefile
index 2b0c15a..ff5c979 100755
--- a/Makefile
+++ b/Makefile
@@ -68,6 +68,18 @@
 functional-single-kind-dt: ROBOT_FILE := Voltha_DT_PODTests.robot
 functional-single-kind-dt: voltha-dt-test
 
+# target to invoke TT Workflow Sanity
+sanity-kind-dt: ROBOT_MISC_ARGS += -i sanityTT $(ROBOT_DEBUG_LOG_OPT)
+sanity-kind-dt: ROBOT_CONFIG_FILE := $(ROBOT_SANITY_TT_SINGLE_PON_FILE)
+sanity-kind-dt: ROBOT_FILE := Voltha_TT_PODTests.robot
+sanity-kind-dt: voltha-tt-test
+
+# target to invoke TT Workflow Functional scenarios
+functional-single-kind-tt: ROBOT_MISC_ARGS += -i sanityTTORfunctional $(ROBOT_DEBUG_LOG_OPT)
+functional-single-kind-tt: ROBOT_CONFIG_FILE := $(ROBOT_SANITY_TT_SINGLE_PON_FILE)
+functional-single-kind-tt: ROBOT_FILE := Voltha_TT_PODTests.robot
+functional-single-kind-tt: voltha-tt-test
+
 # target to invoke multiple OLTs Functional scenarios
 functional-multi-olt: ROBOT_MISC_ARGS += -i sanityMultiOLT $(ROBOT_DEBUG_LOG_OPT)
 functional-multi-olt: ROBOT_CONFIG_FILE := $(ROBOT_SANITY_MULTIPLE_OLT_FILE)
diff --git a/libraries/utils.robot b/libraries/utils.robot
index 39173e8..688b9a2 100644
--- a/libraries/utils.robot
+++ b/libraries/utils.robot
@@ -258,6 +258,43 @@
     Run Keyword    Wait Until Keyword Succeeds    ${timeout}    5s    Validate ONU Flows
     ...    ${List_ONU_Serial}    ${onu_flows}
 
+Perform Sanity Test TT
+    [Documentation]    This keyword performs Sanity Test Procedure for TT Workflow
+    ...    Sanity test performs dhcp and pings (without EAPOL and DHCP flows) for all the ONUs given for the POD
+    ...    This keyword can be used to call in any other tests where sanity check is required
+    ...    and avoids duplication of code.
+    ${of_id}=    Wait Until Keyword Succeeds    ${timeout}    15s    Validate OLT Device in ONOS    ${olt_serial_number}
+    Set Global Variable    ${of_id}
+    ${nni_port}=    Run Keyword And Continue On Failure    Wait Until Keyword Succeeds    ${timeout}    2s
+    ...    Get NNI Port in ONOS    ${of_id}
+    Set Global Variable    ${nni_port}
+    FOR    ${I}    IN RANGE    0    ${num_onus}
+        ${src}=    Set Variable    ${hosts.src[${I}]}
+        ${dst}=    Set Variable    ${hosts.dst[${I}]}
+        ${onu_device_id}=    Get Device ID From SN    ${src['onu']}
+        ${onu_port}=    Run Keyword And Continue On Failure    Wait Until Keyword Succeeds    ${timeout}    2s
+        ...    Get ONU Port in ONOS    ${src['onu']}    ${of_id}
+        # Check ONU port is Enabled in ONOS
+        Run Keyword And Continue On Failure    Wait Until Keyword Succeeds   120s   2s
+        ...    Verify ONU Port Is Enabled   ${ONOS_SSH_IP}    ${ONOS_SSH_PORT}    ${src['onu']}
+        Run Keyword And Continue On Failure    Wait Until Keyword Succeeds    ${timeout}    2
+        ...    Execute ONOS CLI Command    ${ONOS_SSH_IP}    ${ONOS_SSH_PORT}
+        ...    volt-add-subscriber-access ${of_id} ${onu_port}
+        Sleep    30s
+        # Verify ONU state in voltha
+        Run Keyword And Continue On Failure    Wait Until Keyword Succeeds    ${timeout}    5s    Validate Device
+        ...    ENABLED    ACTIVE    REACHABLE
+        ...    ${src['onu']}    onu=True    onu_reason=omci-flows-pushed
+        # TODO: Yet to Verify on the GPON based Physical POD (VOL-2652)
+        Run Keyword If    ${has_dataplane}    Run Keyword And Continue On Failure    Validate DHCP and Ping    True
+        ...    True    ${src['dp_iface_name']}    ${src['s_tag']}    ${src['c_tag']}    ${dst['dp_iface_ip_qinq']}
+        ...    ${src['ip']}    ${src['user']}    ${src['pass']}    ${src['container_type']}    ${src['container_name']}
+        ...    ${dst['dp_iface_name']}    ${dst['ip']}    ${dst['user']}    ${dst['pass']}    ${dst['container_type']}
+        ...    ${dst['container_name']}
+        Run Keyword and Ignore Error    Get Device Output from Voltha    ${onu_device_id}
+        Run Keyword and Ignore Error    Collect Logs
+    END
+
 Setup
     [Documentation]    Pre-test Setup
     #test for empty device list
diff --git a/tests/tt-workflow/Voltha_TT_PODTests.robot b/tests/tt-workflow/Voltha_TT_PODTests.robot
new file mode 100644
index 0000000..886cca4
--- /dev/null
+++ b/tests/tt-workflow/Voltha_TT_PODTests.robot
@@ -0,0 +1,106 @@
+# Copyright 2017 - present Open Networking Foundation
+#
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+# FIXME Can we use the same test against BBSim and Hardware?
+
+*** Settings ***
+Documentation     Test various functional end-to-end scenarios for TT workflow
+Suite Setup       Setup Suite
+Test Setup        Setup
+Test Teardown     Teardown
+Suite Teardown    Teardown Suite
+Library           Collections
+Library           String
+Library           OperatingSystem
+Library           XML
+Library           RequestsLibrary
+Library           ../../libraries/DependencyLibrary.py
+Resource          ../../libraries/onos.robot
+Resource          ../../libraries/voltctl.robot
+Resource          ../../libraries/voltha.robot
+Resource          ../../libraries/utils.robot
+Resource          ../../libraries/k8s.robot
+Resource          ../../variables/variables.robot
+Resource          ../../libraries/power_switch.robot
+
+*** Variables ***
+${POD_NAME}       flex-ocp-cord
+${KUBERNETES_CONF}    ${KUBERNETES_CONFIGS_DIR}/${POD_NAME}.conf
+${KUBERNETES_CONFIGS_DIR}    ~/pod-configs/kubernetes-configs
+#${KUBERNETES_CONFIGS_DIR}    ${KUBERNETES_CONFIGS_DIR}/${POD_NAME}.conf
+${KUBERNETES_YAML}    ${KUBERNETES_CONFIGS_DIR}/${POD_NAME}.yml
+${HELM_CHARTS_DIR}    ~/helm-charts
+${VOLTHA_POD_NUM}    8
+${NAMESPACE}      voltha
+# For below variable value, using deployment name as using grep for
+# parsing radius pod name, we can also use full radius pod name
+${RESTART_POD_NAME}    radius
+${timeout}        60s
+${of_id}          0
+${logical_id}     0
+${has_dataplane}    True
+${teardown_device}    False
+${scripts}        ../../scripts
+
+# Per-test logging on failure is turned off by default; set this variable to enable
+${container_log_dir}    ${None}
+
+*** Test Cases ***
+Reboot TT ONUs Physically - Clean Up
+    [Documentation]   This test reboots ONUs physically before execution all the tests
+    ...    Test case runs only on the PODs that are configured with PowerSwitch that
+    ...    controls the power off/on ONUs/OLT remotely (simulating a physical reboot)
+    [Tags]    functional   PowerSwitch    RebootAllTTONUs
+    [Setup]    Start Logging    RebootAllTTONUs
+    [Teardown]    Run Keywords    Collect Logs
+    ...           AND             Stop Logging    RebootAllTTONUs
+    Power Switch Connection Suite    ${web_power_switch.ip}    ${web_power_switch.user}    ${web_power_switch.password}
+    FOR    ${I}    IN RANGE    0    ${num_onus}
+        ${src}=    Set Variable    ${hosts.src[${I}]}
+        ${dst}=    Set Variable    ${hosts.dst[${I}]}
+        Disable Switch Outlet    ${src['power_switch_port']}
+        Sleep    60s
+        Enable Switch Outlet    ${src['power_switch_port']}
+        Sleep    60s
+    END
+
+Sanity E2E Test for TT
+    [Documentation]    Validates E2E Ping Connectivity and object states for the given scenario:
+    ...    Validate successful DHCP/E2E ping (no EAPOL and DHCP flows) for the tech profile that is used
+    ...    Traffic sent with same vlan from different RGs,
+    ...    should reach the NNI port on the OLT with the expected double tagged vlan ids
+    ...    Inner vlans from the RG should not change
+    [Tags]    sanityTT
+    [Setup]    Run Keywords    Start Logging    SanityTestTT
+    ...        AND             Setup
+    [Teardown]    Run Keywords    Collect Logs
+    ...           AND             Stop Logging    SanityTestTT
+    Run Keyword If    ${has_dataplane}    Clean Up Linux
+    Wait Until Keyword Succeeds    ${timeout}    2s    Perform Sanity Test TT
+    Run Keyword If    ${has_dataplane}    Clean Up Linux
+
+*** Keywords ***
+Setup Suite
+    [Documentation]    Set up the test suite
+    Common Test Suite Setup
+    ${switch_type}=    Get Variable Value    ${web_power_switch.type}
+    Run Keyword If  "${switch_type}"!=""    Set Global Variable    ${powerswitch_type}    ${switch_type}
+
+
+Clear All Devices Then Create New Device
+    [Documentation]    Remove any devices from VOLTHA and ONOS
+    # Remove all devices from voltha and nos
+    Delete All Devices and Verify
+    # Execute normal test Setup Keyword
+    Setup
+