VOL-1790 test framework and sanity test commit
Change-Id: I66b8f93927232c13c62f6c0459f1f7afacf100e6
diff --git a/tests/sanity/sanity.robot b/tests/sanity/sanity.robot
new file mode 100644
index 0000000..7f6295f
--- /dev/null
+++ b/tests/sanity/sanity.robot
@@ -0,0 +1,106 @@
+# Copyright 2017-present Open Networking Foundation
+#
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+
+*** Settings ***
+Documentation Creates bbsim olt/onu and validates activataion
+... Assumes voltha-go, go-based onu/olt adapters, and bbsim are installed
+... voltctl and kubectl should be configured prior to running these tests
+Library OperatingSystem
+Resource ${CURDIR}/../../libraries/utils.robot
+Resource ${CURDIR}/../../variables/variables.robot
+Suite Setup Setup
+Suite Teardown Teardown
+
+*** Variables ***
+${server_ip} localhost
+${timeout} 90s
+${num_onus} 1
+
+*** Test Cases ***
+Activate Device BBSIM OLT/ONU
+ [Documentation] Validate deployment ->
+ ... create and enable bbsim device ->
+ ... re-validate deployment
+ [Tags] activate
+ #create/preprovision device
+ ${rc} ${device_id}= Run and Return Rc and Output voltctl device create -t openolt -H ${BBSIM_SERVICE}:${BBSIM_PORT}
+ Should Be Equal As Integers ${rc} 0
+ #enable device
+ ${rc} ${output}= Run and Return Rc and Output voltctl device enable ${device_id}
+ Should Be Equal As Integers ${rc} 0
+ #validate olt states
+ Wait Until Keyword Succeeds 60s 5s Validate Device ${BBSIM_OLT_SN} ENABLED ACTIVE REACHABLE
+ #validate onu states
+ Wait Until Keyword Succeeds 60s 5s Validate Device ${BBSIM_ONU_SN} ENABLED ACTIVE REACHABLE
+
+Validate OLT Connected to ONOS
+ [Documentation] Verifies the BBSIM-OLT device is activated in onos
+ [Tags] notready
+ Wait Until Keyword Succeeds ${timeout} 5s BBSIM OLT Device in ONOS
+
+Check EAPOL Flows in ONOS
+ [Documentation] Validates eapol flows for the onu are pushed from voltha
+ [Tags] notready
+ Wait Until Keyword Succeeds ${timeout} 5s Verify Eapol Flows Added
+
+Validate ONU Authenticated in ONOS
+ [Documentation] Validates onu is AUTHORIZED in ONOS as bbsim will attempt to authenticate
+ [Tags] notready
+ Wait Until Keyword Succeeds ${timeout} 5s Verify Number of AAA-Users ${number_of_onus}
+
+Provision ONU Subscriber in ONOS
+ [Documentation] Through the olt-app in ONOS, execute 'volt-add-subscriber-access' and validate IP Flows
+ [Tags] notready
+
+Validate DHCP Assignment in ONOS
+ [Documentation] After IP Flows are pushed to the device, BBSIM will start a dhclient for the ONU.
+ [Tags] notready
+
+*** Keywords ***
+Setup
+ [Documentation] Create HTTP Session with the ONOS Controller
+ ${onos_auth}= Create List karaf karaf
+ ${HEADERS} Create Dictionary Content-Type=application/json
+ Create Session ONOS http://${server_ip}:${ONOS_REST_PORT} auth=${ONOS_AUTH}
+
+Teardown
+ [Documentation] Delete all http sessions
+ Delete All Sessions
+
+BBSIM OLT Device in ONOS
+ [Documentation] Checks if bbsim olt has been connected to ONOS
+ ${resp}= Get Request ONOS onos/v1/devices
+ ${jsondata}= To Json ${resp.content}
+ Should Not Be Empty ${jsondata['devices']}
+ ${length}= Get Length ${jsondata['devices']}
+ @{serial_numbers}= Create List
+ : FOR ${INDEX} IN RANGE 0 ${length}
+ \ ${value}= Get From List ${jsondata['devices']} ${INDEX}
+ \ ${sn}= Get From Dictionary ${value} serial
+ \ ${dpid}= Get From Dictionary ${value} id
+ Should Be Equal As Strings ${dpid} ${BBSIM_DEVICE_ID}
+ Should Be Equal As Strings ${sn} ${BBSIM_OLT_SN}
+
+Verify Eapol Flows Added
+ [Arguments] ${expected_onus}
+ [Documentation] Matches for number of eapol flows based on number of onus
+ ${eapol_flows_added}= Execute ONOS Command flows -s -f ADDED | grep eapol | wc -l
+ Should Contain ${eapol_flows_added} ${expected_onus}
+
+Verify Number of AAA-Users
+ [Arguments] ${expected_onus}
+ [Documentation] Matches for number of aaa-users authorized based on number of onus
+ ${aaa_users}= Execute ONOS Command aaa-users | grep AUTHORIZED | wc -l
+ Should Contain ${aaa_users} ${expected_onus}
\ No newline at end of file