diff --git a/tests/sanity/sanity.robot b/tests/sanity/sanity.robot
new file mode 100644
index 0000000..7f6295f
--- /dev/null
+++ b/tests/sanity/sanity.robot
@@ -0,0 +1,106 @@
+# Copyright 2017-present Open Networking Foundation
+#
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+
+*** Settings ***
+Documentation     Creates bbsim olt/onu and validates activataion
+...               Assumes voltha-go, go-based onu/olt adapters, and bbsim are installed
+...               voltctl and kubectl should be configured prior to running these tests
+Library           OperatingSystem
+Resource          ${CURDIR}/../../libraries/utils.robot
+Resource          ${CURDIR}/../../variables/variables.robot
+Suite Setup       Setup
+Suite Teardown    Teardown
+
+*** Variables ***
+${server_ip}    localhost
+${timeout}      90s
+${num_onus}     1
+
+*** Test Cases ***
+Activate Device BBSIM OLT/ONU
+    [Documentation]    Validate deployment ->
+    ...    create and enable bbsim device ->
+    ...    re-validate deployment
+    [Tags]    activate
+    #create/preprovision device
+    ${rc}    ${device_id}=    Run and Return Rc and Output    voltctl device create -t openolt -H ${BBSIM_SERVICE}:${BBSIM_PORT}
+    Should Be Equal As Integers    ${rc}    0
+    #enable device
+    ${rc}    ${output}=    Run and Return Rc and Output    voltctl device enable ${device_id}
+    Should Be Equal As Integers    ${rc}    0
+    #validate olt states
+    Wait Until Keyword Succeeds    60s    5s    Validate Device    ${BBSIM_OLT_SN}    ENABLED    ACTIVE    REACHABLE
+    #validate onu states
+    Wait Until Keyword Succeeds    60s    5s    Validate Device    ${BBSIM_ONU_SN}    ENABLED    ACTIVE    REACHABLE
+
+Validate OLT Connected to ONOS
+    [Documentation]    Verifies the BBSIM-OLT device is activated in onos
+    [Tags]    notready
+    Wait Until Keyword Succeeds    ${timeout}    5s    BBSIM OLT Device in ONOS
+
+Check EAPOL Flows in ONOS
+    [Documentation]    Validates eapol flows for the onu are pushed from voltha
+    [Tags]    notready
+    Wait Until Keyword Succeeds    ${timeout}    5s    Verify Eapol Flows Added
+
+Validate ONU Authenticated in ONOS
+    [Documentation]    Validates onu is AUTHORIZED in ONOS as bbsim will attempt to authenticate
+    [Tags]    notready
+    Wait Until Keyword Succeeds    ${timeout}    5s    Verify Number of AAA-Users    ${number_of_onus}
+
+Provision ONU Subscriber in ONOS
+    [Documentation]    Through the olt-app in ONOS, execute 'volt-add-subscriber-access' and validate IP Flows
+    [Tags]    notready
+
+Validate DHCP Assignment in ONOS
+    [Documentation]    After IP Flows are pushed to the device, BBSIM will start a dhclient for the ONU.
+    [Tags]    notready
+
+*** Keywords ***
+Setup
+    [Documentation]    Create HTTP Session with the ONOS Controller
+    ${onos_auth}=    Create List    karaf    karaf
+    ${HEADERS}    Create Dictionary    Content-Type=application/json
+    Create Session    ONOS    http://${server_ip}:${ONOS_REST_PORT}    auth=${ONOS_AUTH}
+
+Teardown
+    [Documentation]    Delete all http sessions
+    Delete All Sessions
+
+BBSIM OLT Device in ONOS
+    [Documentation]    Checks if bbsim olt has been connected to ONOS
+    ${resp}=    Get Request    ONOS    onos/v1/devices
+    ${jsondata}=    To Json    ${resp.content}
+    Should Not Be Empty    ${jsondata['devices']}
+    ${length}=    Get Length    ${jsondata['devices']}
+    @{serial_numbers}=    Create List
+    : FOR    ${INDEX}    IN RANGE    0    ${length}
+    \    ${value}=    Get From List    ${jsondata['devices']}    ${INDEX}
+    \    ${sn}=    Get From Dictionary    ${value}    serial
+    \    ${dpid}=    Get From Dictionary    ${value}    id
+    Should Be Equal As Strings    ${dpid}    ${BBSIM_DEVICE_ID}
+    Should Be Equal As Strings    ${sn}    ${BBSIM_OLT_SN}
+
+Verify Eapol Flows Added
+    [Arguments]    ${expected_onus}
+    [Documentation]    Matches for number of eapol flows based on number of onus
+    ${eapol_flows_added}=    Execute ONOS Command    flows -s -f ADDED | grep eapol | wc -l
+    Should Contain    ${eapol_flows_added}    ${expected_onus}
+
+Verify Number of AAA-Users
+    [Arguments]    ${expected_onus}
+    [Documentation]    Matches for number of aaa-users authorized based on number of onus
+    ${aaa_users}=    Execute ONOS Command    aaa-users | grep AUTHORIZED | wc -l
+    Should Contain    ${aaa_users}    ${expected_onus}
\ No newline at end of file