# Copyright 2017 - present Open Networking Foundation
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
# FIXME Can we use the same test against BBSim and Hardware?

*** Settings ***
Documentation     Test various functional end-to-end scenarios for TT workflow
Suite Setup       Setup Suite
Test Setup        Setup
Test Teardown     Teardown
Suite Teardown    Teardown Suite
Library           Collections
Library           String
Library           OperatingSystem
Library           XML
Library           RequestsLibrary
Library           ../../libraries/DependencyLibrary.py
Resource          ../../libraries/onos.robot
Resource          ../../libraries/voltctl.robot
Resource          ../../libraries/voltha.robot
Resource          ../../libraries/utils.robot
Resource          ../../libraries/k8s.robot
Resource          ../../variables/variables.robot
Resource          ../../libraries/power_switch.robot

*** Variables ***
${POD_NAME}       flex-ocp-cord
${KUBERNETES_CONF}    ${KUBERNETES_CONFIGS_DIR}/${POD_NAME}.conf
${KUBERNETES_CONFIGS_DIR}    ~/pod-configs/kubernetes-configs
#${KUBERNETES_CONFIGS_DIR}    ${KUBERNETES_CONFIGS_DIR}/${POD_NAME}.conf
${KUBERNETES_YAML}    ${KUBERNETES_CONFIGS_DIR}/${POD_NAME}.yml
${HELM_CHARTS_DIR}    ~/helm-charts
${VOLTHA_POD_NUM}    8
${NAMESPACE}      voltha
# For below variable value, using deployment name as using grep for
# parsing radius pod name, we can also use full radius pod name
${RESTART_POD_NAME}    radius
${timeout}        60s
${of_id}          0
${logical_id}     0
${has_dataplane}    True
${teardown_device}    True
${scripts}        ../../scripts

# Per-test logging on failure is turned off by default; set this variable to enable
${container_log_dir}    ${None}

*** Test Cases ***
Reboot TT ONUs Physically - Clean Up
    [Documentation]   This test reboots ONUs physically before execution all the tests
    ...    Test case runs only on the PODs that are configured with PowerSwitch that
    ...    controls the power off/on ONUs/OLT remotely (simulating a physical reboot)
    [Tags]    functionalTT   PowerSwitch    RebootAllTTONUs
    [Setup]    Start Logging    RebootAllTTONUs
    [Teardown]    Run Keywords    Collect Logs
    ...           AND             Stop Logging    RebootAllTTONUs
    Power Switch Connection Suite    ${web_power_switch.ip}    ${web_power_switch.user}    ${web_power_switch.password}
    FOR    ${I}    IN RANGE    0    ${num_all_onus}
        ${src}=    Set Variable    ${hosts.src[${I}]}
        ${dst}=    Set Variable    ${hosts.dst[${I}]}
        Disable Switch Outlet    ${src['power_switch_port']}
        Sleep    10s
        Enable Switch Outlet    ${src['power_switch_port']}
    END

Sanity E2E Test for TT (HSIA, VoD, VoIP)
    [Documentation]    Validates E2E Ping Connectivity and object states for the given scenario:
    ...    Validate successful DHCP/E2E ping (no EAPOL and DHCP flows) for the tech profile that is used
    ...    Traffic sent with same vlan from different RGs,
    ...    should reach the NNI port on the OLT with the expected double tagged vlan ids
    ...    Inner vlans from the RG should not change
    [Tags]    sanityTT
    [Setup]    Run Keywords    Start Logging    SanityTestTT
    ...        AND             Setup
    [Teardown]    Run Keywords    Collect Logs
    ...           AND             Stop Logging    SanityTestTT
    Run Keyword If    ${has_dataplane}    Clean Up Linux
    Wait Until Keyword Succeeds    ${timeout}    2s    Perform Sanity Test TT
    #Run Keyword If    ${has_dataplane}    Clean Up Linux

Sanity E2E Test for TT (MCAST)
    [Documentation]    Validates E2E Ping Connectivity and object states for the given scenario:
    ...    Validate successful DHCP/E2E ping (no EAPOL and DHCP flows) for the tech profile that is used
    ...    Traffic sent with same vlan from different RGs,
    ...    should reach the NNI port on the OLT with the expected double tagged vlan ids
    ...    Inner vlans from the RG should not change
    [Tags]    sanityTT-MCAST
    [Setup]    Run Keyword    Start Logging    SanityTestTT-MCAST
    [Teardown]    Run Keywords    Collect Logs
    ...           AND             Stop Logging    SanityTestTT-MCAST
    Run Keyword If    ${has_dataplane}    Clean Up Linux
    Wait Until Keyword Succeeds    ${timeout}    2s    Perform Sanity Test TT MCAST

Test Disable and Delete OLT for TT
    [Documentation]    Validates E2E Ping Connectivity and object states for the given scenario:
    ...    Assuming that all the ONUs are DHCP/pingable (i.e. assuming sanityTt test was executed)
    ...    Perform disable on the OLT and validate ONUs state and that the pings do not succeed
    ...    Perform delete on the OLT, Re-do Setup (Recreate the OLT) and Perform Sanity Test TT
    [Tags]    functionalTT    DisableDeleteOLTTt    notready
    [Setup]    Start Logging    DisableDeleteOLTTt
    [Teardown]    Run Keywords    Collect Logs
    ...           AND             Stop Logging    DisableDeleteOLTTt
    # Disable and Validate OLT Device
    FOR   ${I}    IN RANGE    0    ${olt_count}
        ${olt_serial_number}=    Get From Dictionary    ${olt_ids}[${I}]    sn
        ${olt_device_id}=    Get OLTDeviceID From OLT List    ${olt_serial_number}
        Disable Device    ${olt_device_id}
        ${of_id}=    Get ofID From OLT List    ${olt_serial_number}
        Run Keyword And Continue On Failure    Wait Until Keyword Succeeds    ${timeout}    5s
        ...    Validate OLT Device    DISABLED    UNKNOWN    REACHABLE
        ...    ${olt_serial_number}
        Wait Until Keyword Succeeds    ${timeout}    5s    Validate OLT Device    DISABLED    UNKNOWN    REACHABLE
        ...    ${olt_serial_number}
        ${num_onus}=    Set Variable    ${list_olts}[${I}][onucount]
        # Validate ONUs
        Run Keyword    Wait Until Keyword Succeeds    ${timeout}    5s    Validate ONUs After OLT Disable
        ...    ${num_onus}    ${olt_serial_number}
        # Verify ONOS Flows
        # Number of Access Flows on ONOS equals 4 * the Number of Active ONUs (2 for each downstream and upstream)
        ${onos_flows_count}=    Evaluate    4 * ${num_onus}
        Run Keyword And Continue On Failure    Wait Until Keyword Succeeds    ${timeout}    5s
        ...    Verify Default Downstream Flows are added in ONOS for OLT TT    ${ONOS_SSH_IP}    ${ONOS_SSH_PORT}    ${of_id}
        ...    ${nni_port}
        # Verify VOLTHA Flows
        # Number of per OLT Flows equals Twice the Number of Active ONUs (each for downstream and upstream) + 1 for LLDP
        ${olt_flows}=    Evaluate    2 * ${num_onus} + 1
        # Number of per ONU Flows equals 2 (one each for downstream and upstream)
        ${onu_flows}=    Set Variable    2
        Run Keyword    Wait Until Keyword Succeeds    ${timeout}    5s    Validate OLT Flows    ${olt_flows}
        ...    ${olt_device_id}
        ${List_ONU_Serial}    Create List
        Set Suite Variable    ${List_ONU_Serial}
        Build ONU SN List    ${List_ONU_Serial}    ${olt_serial_number}    ${num_onus}
        Log    ${List_ONU_Serial}
        Run Keyword    Wait Until Keyword Succeeds    ${timeout}    5s    Validate ONU Flows
        ...    ${List_ONU_Serial}    ${onu_flows}
        # Delete OLT and Validate Empty Device List
        Delete Device    ${olt_device_id}
        # Check that the OLT and the ONUs are actually removed from the system
        Run Keyword And Continue On Failure    Wait Until Keyword Succeeds    ${timeout}    5s    Validate Device Removed
        ...    ${olt_serial_number}
        Run Keyword and Continue On Failure    Validate all ONUS for OLT Removed    ${num_all_onus}    ${hosts}
        ...    ${olt_serial_number}    ${timeout}
        Run Keyword And Continue On Failure    Wait Until Keyword Succeeds    ${timeout}    5s
        ...    Verify Device Flows Removed    ${ONOS_SSH_IP}    ${ONOS_SSH_PORT}    ${of_id}
    END
    # Re-do Setup (Recreate the OLT) and Perform Sanity Test TT
    Run Keyword    Setup
    Run Keyword If    ${has_dataplane}    Clean Up Linux
    Wait Until Keyword Succeeds    ${timeout}   2s    Perform Sanity Tests TT

*** Keywords ***
Setup Suite
    [Documentation]    Set up the test suite
    Common Test Suite Setup
    ${switch_type}=    Get Variable Value    ${web_power_switch.type}
    Run Keyword If  "${switch_type}"!=""    Set Global Variable    ${powerswitch_type}    ${switch_type}


Clear All Devices Then Create New Device
    [Documentation]    Remove any devices from VOLTHA and ONOS
    # Remove all devices from voltha and nos
    Delete All Devices and Verify
    # Execute normal test Setup Keyword
    Setup


Teardown Suite
    [Documentation]    Tear down steps for the suite
    Run Keyword If    ${has_dataplane}    Clean Up Linux
    Run Keyword If    ${teardown_device}    Delete All Devices And Verify