Developer notes:

Before auto-discovery is implemented, you can follow the steps below to activate a Tibit PON. These steps assume:

• Voltha code was downloaded and compiled successfully
• Voltha starts with fresh state (was just launched in single-instance mode)
• Tibit OLT and ONU(s) are powered on and properly connected with splitters
• There is a network reachable from Voltha's host environment to the Tibit OLT via a specific interface of the host OS. We symbolically refer to this Linux interface as <interface>.
• All commands are to be executed from the root dir of the voltha project

Step 1: Launch Voltha support applications and Chameleon

Open a shell and execute the following commands.

$ cd voltha
$ . ./env.sh
(venv-linux)$ docker-compose -f compose/docker-compose-system-test.yml up -d consul kafka zookeeper fluentd registrator

In the same shell, launch chameleon. The command below assumes that you are in the top level Voltha directory.

(venv-linux)$ ./chameleon/main.py  -f pki/voltha.crt -k pki/voltha.key

Step 2: Launch Voltha with the proper interface value.

Note: For Voltha to properly access the interface, it needs to be run with sudo priveleges.

$ sudo -s
# cd ~/cord/incubator/voltha
# . ./env.sh
(venv-linux)# ./voltha/main.py --interface <interface>

Also, the interface being used for Voltha needs to be in promiscuous mode. To set the interface in promiscuous mode, use the following command.

$ sudo ip link set <interface> promisc on

Step 3: Verify Tibit adapters loaded

In a third terminal, issue the following REST requests:

$ curl -k -s https://localhost:8881/api/v1/local/adapters | jq

This should list (among other entries) two entries for Tibit devices, one for the Tibit OLT and one for the Tibit ONU.

The following request should show the device types supported:

$ curl -k -s https://localhost:8881/api/v1/local/device_types | jq

This should include two entries for Tibit devices, one for the OLT and one for the ONU.

Step 4: Pre-provision a Tibit OLT

Issue the following command to pre-provision the Tibit OLT:

curl -k -s -X POST -d '{"type": "tibit_olt", "mac_address": "00:0c:e2:31:06:00"}' \
    https://localhost:8881/api/v1/local/devices | jq '.' | tee olt.json

This will return a complete Device JSON object, including a 12-character id of the new device and a preprovisioned state as admin state (it also saved the json blob in a olt.json file):

{
  "vendor": "",
  "software_version": "",
  "parent_port_no": 0,
  "connect_status": "UNKNOWN",
  "root": false,
  "adapter": "tibit_olt",
  "vlan": 0,
  "hardware_version": "",
  "ports": [],
  "parent_id": "",
  "oper_status": "UNKNOWN",
  "admin_state": "PREPROVISIONED",
  "mac_address": "00:00:00:00:00:01",
  "serial_number": "",
  "model": "",
  "type": "tibit_olt",
  "id": "2db8e16804ec",
  "firmware_version": ""
}

For simplicity, store the device id as shell variable:

OLT_ID=$(jq .id olt.json | sed 's/"//g')

Step 5: Activate the OLT

To activate the OLT, issue the following using the OLT_ID memorized above:

curl -k -s -X POST https://localhost:8881/api/v1/local/devices/$OLT_ID/activate

After this, if you retrieve the state of the OLT device, it should be enabled and in the 'ACTIVE' operational status. If it is not in the 'ACTIVE' operational status it is likely that the handshake with the OLT device was not successful.

curl https://localhost:8881/api/v1/local/devices/$OLT_ID | jq '.oper_status,.admin_state'
"ACTIVE"
"ENABLED"

When the device is ACTIVE, the logical devices and logical ports should be created. To check the logical devices and logical ports, use the following commands.

curl -k -s https://localhost:8881/api/v1/local/logical_devices | jq '.'
# Note: Need to pull out logical device id.
curl -k -s https://localhost:8881/api/v1/local/logical_devices/47d2bb42a2c6/ports | jq '.'

Running the ONOS olt-test

To get the EOAM stack to work with the ONOS olt-test, the following command was used in the shell to launch the olt-test.

$ cd <LOCATION_OF_VOLTHA>
$ sudo -s
# . ./env.sh
(venv-linux) # PYTHONPATH=$HOME/cord/incubator/voltha/voltha/extensions/eoam ./oftest/oft --test-dir=olt-oftest/ -i 1@enp1s0f0 -i 2@enp1s0f1 --port 6653 -V 1.3 -t "olt_port=1;onu_port=2;in_out_port=1;device_type='tibit'" olt-complex.TestScenario1SingleOnu