Minor fixes
Change-Id: I5d1d38242340056d711b4325b9b6bc7bfd32e0a4
diff --git a/developer/aiabhw.rst b/developer/aiabhw.rst
index e405c4a..2119fed 100644
--- a/developer/aiabhw.rst
+++ b/developer/aiabhw.rst
@@ -70,10 +70,10 @@
sequenceNumber: 135
Determine which is the interface that has L3 connectivity to the
-eNodeB -- this will be *DATA_IFACE* in the configuration later. If
+eNodeB -- this will be ``DATA_IFACE`` in the configuration later. If
the eNodeB will also be connected to the local network, then this is just the
server’s primary interface. If the eNodeB will be connected via an
-isolated L2/L3 network segment, then *DATA_IFACE* refers to the server
+isolated L2/L3 network segment, then ``DATA_IFACE`` refers to the server
interface on that network. Remember this interface for later.
Option 1: Configure Aether with ROC
@@ -83,26 +83,26 @@
Aether. If you don’t wish to use the ROC to configure AiaB, you
can skip to the next section.
-Install AiaB as follows (specifying *DATA_IFACE* from above)::
+Install AiaB as follows (specifying ``DATA_IFACE`` from above)::
ENABLE_OAISIM=false DATA_IFACE=<iface> CHARTS=latest make roc-4g-models 4g-core
Next, use the ROC to add information about your SIM cards.
The ROC GUI is available at `http://<server-ip>:31194`.
-Choose *Configuration > Site* from the drop-down at top right and edit
-the “AiaB site”. Change the following values and click “Update”:
+Choose ``Configuration > Site`` from the drop-down at top right and edit
+the ``AiaB site``. Change the following values and click ``Update``:
* MCC: 315
* MNC: 010
-Choose *Sim Cards* from the drop-down at top right. Edit the
+Choose ``Sim Cards`` from the drop-down at top right. Edit the
existing entries to reflect the SIM cards you are adding to devices
-by replacing their IMSI values. Click “Update” after each edit.
+by replacing their IMSI values. Click ``Update`` after each edit.
If you want to connect more than two devices, consult the `ROC
documentation <https://docs.aetherproject.org/master/operations/subscriber.html#configure-connectivity-service-for-a-new-device>`_.
-Finally, click the Basket icon at top right and click the “Commit” button.
+Finally, click the Basket icon at top right and click the ``Commit`` button.
Now jump to the `Verifying the AiaB installation`_ section.
@@ -128,7 +128,7 @@
- "315010999912302"
- "315010999912303"
-Install AiaB as follows (specifying *DATA_IFACE* from above)::
+Install AiaB as follows (specifying ``DATA_IFACE`` from above)::
ENABLE_OAISIM=false DATA_IFACE=<iface> CHARTS=latest make 4g-core
@@ -136,10 +136,10 @@
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Installing AiaB will take about 20 minutes with a fast Internet
-connection. If you see any errors / timeouts, try running the `make`
+connection. If you see any errors / timeouts, try running the ``make``
command again. The build will finish with a message:
“Your MME IP address is… ” This is just the IP address assigned to
-the *DATA_IFACE*. Remember this for the eNodeB setup.
+the ``DATA_IFACE``. Remember this for the eNodeB setup.
When the install is complete, check that the 4G SD-CORE is running
as follows::
@@ -187,13 +187,13 @@
Connect the eNodeB LAN port to a free Ethernet port on a Linux machine
(say, a laptop) that will be used for the initial configuration of
-the eNodeB. On that machine run `dhclient` on the interface corresponding
+the eNodeB. On that machine run ``dhclient`` on the interface corresponding
to the Ethernet port, for example::
sudo dhclient eth1
The interface should receive an IP address from the Sercomm eNodeB on
-the 11.11.11.0/24 subnet. Check this using `ifconfig`::
+the 11.11.11.0/24 subnet. Check this using ``ifconfig``::
$ ifconfig eth1
eth1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
@@ -212,10 +212,10 @@
To access the Sercomm eNodeB admin page, you can run a Web browser on
the laptop and direct it to `https://11.11.11.188`. Login to the admin
-interface as user: *sc_femto* and password: *scHt3pp*.
+interface as user: ``sc_femto`` and password: ``scHt3pp``.
Click the ``NetWork set`` menu at the top. In the first section
-“IP Address”, set *Connect type: DHCP* (assuming this is supported on
+``IP Address``, set *Connect type: DHCP* (assuming this is supported on
your local network, otherwise set up a static IP address).
Click the blue ``Save`` button at the bottom.
@@ -258,7 +258,7 @@
* GatewayIPAddress: <Use MME IP address from AiaB installation>
* Interface: Device.IP.Interface.1.
-Then click the “Add” button at the far right.
+Then click the ``Add`` button at the far right.
Finally click the ``FAPService`` menu and then go to the ``FAPControl``
tab. Check the box next to ``AdminState`` in the first section and