blob: bc12ee8a301f6f43c18d9f41b8c0bb02604d6489 [file] [log] [blame]
/*
* Copyright (c) 2018 - present. Boling Consulting Solutions (bcsw.net)
* Copyright 2020-present Open Networking Foundation
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at
* http://www.apache.org/licenses/LICENSE-2.0
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*/
/*
* NOTE: This file was generated, manual edits will be overwritten!
*
* Generated by 'goCodeGenerator.py':
* https://github.com/cboling/OMCI-parser/README.md
*/
package generated
import "github.com/deckarep/golang-set"
// PhysicalPathTerminationPointPotsUniClassID is the 16-bit ID for the OMCI
// Managed entity Physical path termination point POTS UNI
const PhysicalPathTerminationPointPotsUniClassID ClassID = ClassID(53)
var physicalpathterminationpointpotsuniBME *ManagedEntityDefinition
// PhysicalPathTerminationPointPotsUni (class ID #53)
// This ME represents a POTS UNI in the ONU, where a physical path terminates and physical path
// level functions (analogue telephony) are performed.
//
// The ONU automatically creates an instance of this ME per port as follows.
//
// o When the ONU has POTS ports built into its factory configuration.
//
// o When a cardholder is provisioned to expect a circuit pack of the POTS type.
//
// o When a cardholder provisioned for plug-and-play is equipped with a circuit pack of the POTS
// type. Note that the installation of a plug-and-play card may indicate the presence of POTS ports
// via equipment ID as well as type, and indeed may cause the ONU to instantiate a port-mapping
// package that specifies POTS ports.
//
// The ONU automatically deletes instances of this ME when a cardholder is neither provisioned to
// expect a POTS circuit pack, nor is it equipped with a POTS circuit pack.
//
// Relationships
// An instance of this ME is associated with each real or pre-provisioned POTS port. Either a SIP
// or a VoIP voice CTP links to the POTS UNI. Status is available from a VoIP line status ME, and
// RTP and call control PM may be collected on this point.
//
// Attributes
// Managed Entity Id
// Managed entity ID: This attribute uniquely identifies each instance of this ME. This 2-byte
// number indicates the physical position of the UNI. The first byte is the slot ID (defined in
// clause 9.1.5). The second byte is the port ID, with the range 1..255. (R) (mandatory) (2-bytes)
//
// Administrative State
// When the administrative state is set to lock, all user functions of this UNI are blocked, and
// alarms, TCAs and AVCs for this ME and all dependent MEs are no longer generated. Selection of a
// default value for this attribute is outside the scope of this Recommendation. (R, W) (mandatory)
// (1 byte)
//
// Deprecated
// Deprecated: This attribute is not used and should not be supported. (R,-W) (optional) (2-bytes)
//
// Arc
// ARC: See clause A.1.4.3. (R,-W) (optional) (1-byte)
//
// Arc Interval
// ARC interval: See clause A.1.4.3. (R,-W) (optional) (1-byte)
//
// Impedance
// where C1, R1, and R2 are related as shown in Figure 9.9.1-1. Upon ME instantiation, the ONU sets
// this attribute to 0. (R,-W) (optional) (1-byte)
//
// Transmission Path
// Transmission path: This attribute allows setting the POTS UNI either to full-time on-hook
// transmission (0) or part-time on-hook transmission (1). Upon ME instantiation, the ONU sets this
// attribute to 0. (R,-W) (optional) (1-byte)
//
// Rx Gain
// Rx gain: This attribute specifies a gain value for the received signal in the form of a 2s
// complement number. Valid values are -120 (12.0-dB) to 60 (+6.0-dB). The direction of the
// affected signal is in the D to A direction, towards the telephone set. Upon ME instantiation,
// the ONU sets this attribute to 0. (R, W) (optional) (1 byte)
//
// Tx Gain
// Tx gain: This attribute specifies a gain value for the transmit signal in the form of a 2s
// complement number. Valid values are -120 (12.0-dB) to 60 (+6.0-dB). The direction of the
// affected signal is in the A to D direction, away from the telephone set. Upon ME instantiation,
// the ONU sets this attribute to 0. (R, W) (optional) (1 byte)
//
// Operational State
// Operational state: This attribute indicates whether the ME is capable of performing its
// function. Valid values are enabled (0) and disabled (1). (R) (optional) (1-byte)
//
// Hook State
// Hook state: This attribute indicates the current state of the subscriber line: 0-= on hook, 1-=
// off hook (R) (optional) (1-byte)
//
// Pots Holdover Time
// POTS holdover time: This attribute determines the time during which the POTS loop voltage is
// held up when a LOS or softswitch connectivity is detected (please refer to the following table
// for description of behaviours).. After the specified time elapses, the ONU drops the loop
// voltage, and may thereby cause premises intrusion alarm or fire panel circuits to go active.
// When the ONU ranges successfully on the PON or softswitch connectivity is restored, it restores
// the POTS loop voltage immediately and resets the timer to zero. The attribute is expressed in
// seconds. The default value 0 selects the vendor's factory policy. (R,-W) (optional) (2-bytes)
//
// Nominal Feed Voltage
// Nominal feed voltage: This attribute indicates the designed nominal feed voltage of the POTS
// loop. It is an absolute value with resolution 1-V. This attribute does not represent the actual
// voltage measured on the loop, which is available through the test command. (R,-W) (optional)
// (1-byte)
//
// Loss Of Softswitch
// Loss of softswitch: This Boolean attribute controls whether the T/R holdover initiation
// criteria. False disables loss of softswitch connectivity detection as criteria for initiating
// the POTS holdover timer. True enables loss of softswitch connectivity detection as criteria for
// initiating the POTS holdover timer. This attribute is optional (if not implemented, the POTS
// holdover time is triggered on a LOS when POTS holdover is greater than zero). (R,-W) (optional)
// (1-byte)
//
type PhysicalPathTerminationPointPotsUni struct {
ManagedEntityDefinition
Attributes AttributeValueMap
}
func init() {
physicalpathterminationpointpotsuniBME = &ManagedEntityDefinition{
Name: "PhysicalPathTerminationPointPotsUni",
ClassID: 53,
MessageTypes: mapset.NewSetWith(
Get,
Set,
Test,
),
AllowedAttributeMask: 0xfff8,
AttributeDefinitions: AttributeDefinitionMap{
0: Uint16Field("ManagedEntityId", PointerAttributeType, 0x0000, 0, mapset.NewSetWith(Read), false, false, false, 0),
1: ByteField("AdministrativeState", UnsignedIntegerAttributeType, 0x8000, 0, mapset.NewSetWith(Read, Write), true, false, false, 1),
2: Uint16Field("Deprecated", UnsignedIntegerAttributeType, 0x4000, 0, mapset.NewSetWith(Read, Write), false, true, true, 2),
3: ByteField("Arc", UnsignedIntegerAttributeType, 0x2000, 0, mapset.NewSetWith(Read, Write), true, true, false, 3),
4: ByteField("ArcInterval", UnsignedIntegerAttributeType, 0x1000, 0, mapset.NewSetWith(Read, Write), false, true, false, 4),
5: ByteField("Impedance", UnsignedIntegerAttributeType, 0x0800, 0, mapset.NewSetWith(Read, Write), false, true, false, 5),
6: ByteField("TransmissionPath", UnsignedIntegerAttributeType, 0x0400, 0, mapset.NewSetWith(Read, Write), false, true, false, 6),
7: ByteField("RxGain", UnsignedIntegerAttributeType, 0x0200, 0, mapset.NewSetWith(Read, Write), false, true, false, 7),
8: ByteField("TxGain", UnsignedIntegerAttributeType, 0x0100, 0, mapset.NewSetWith(Read, Write), false, true, false, 8),
9: ByteField("OperationalState", UnsignedIntegerAttributeType, 0x0080, 0, mapset.NewSetWith(Read), true, true, false, 9),
10: ByteField("HookState", UnsignedIntegerAttributeType, 0x0040, 0, mapset.NewSetWith(Read), false, true, false, 10),
11: Uint16Field("PotsHoldoverTime", UnsignedIntegerAttributeType, 0x0020, 0, mapset.NewSetWith(Read, Write), false, true, false, 11),
12: ByteField("NominalFeedVoltage", UnsignedIntegerAttributeType, 0x0010, 0, mapset.NewSetWith(Read, Write), false, true, false, 12),
13: ByteField("LossOfSoftswitch", UnsignedIntegerAttributeType, 0x0008, 0, mapset.NewSetWith(Read, Write), false, true, false, 13),
},
Access: CreatedByOnu,
Support: UnknownSupport,
}
}
// NewPhysicalPathTerminationPointPotsUni (class ID 53) creates the basic
// Managed Entity definition that is used to validate an ME of this type that
// is received from or transmitted to the OMCC.
func NewPhysicalPathTerminationPointPotsUni(params ...ParamData) (*ManagedEntity, OmciErrors) {
return NewManagedEntity(*physicalpathterminationpointpotsuniBME, params...)
}