blob: 9623bed6d7077117641c38fcf96fd59b383e0373 [file] [log] [blame]
/*
* Copyright (c) 2018 - present. Boling Consulting Solutions (bcsw.net)
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at
* http://www.apache.org/licenses/LICENSE-2.0
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*/
/*
* NOTE: This file was generated, manual edits will be overwritten!
*
* Generated by 'goCodeGenerator.py':
* https://github.com/cboling/OMCI-parser/README.md
*/
package generated
import "github.com/deckarep/golang-set"
const XdslLineConfigurationProfilePart3ClassId ClassID = ClassID(106)
var xdsllineconfigurationprofilepart3BME *ManagedEntityDefinition
// XdslLineConfigurationProfilePart3 (class ID #106)
// The overall xDSL line configuration profile is modelled in several parts, all of which are
// associated together through a common ME ID (the client PPTP xDSL UNI part 1 has a single
// pointer, which refers to the entire set of line configuration profile parts).
//
// Relationships
// An instance of this ME may be associated with zero or more instances of an xDSL UNI.
//
// Attributes
// Managed Entity Id
// Managed entity ID: This attribute uniquely identifies each instance of this ME. All xDSL and
// VDSL2 line configuration profiles and extensions that pertain to a given PPTP xDSL UNI must
// share a common ME ID. (R, setbycreate) (mandatory) (2 bytes)
//
// Loop Diagnostics Mode Forced Ldsf
// Only while the line power management state is L3 can the line be forced into loop diagnostic
// mode. When loop diagnostic procedures complete successfully, the ONU resets this attribute to 0.
// The line remains in the L3 idle state. The loop diagnostics data are available at least until
// the line is forced to the L0 state. As long as loop diagnostic procedures have not completed
// successfully, attempts are made to do so, until the loop diagnostic mode is no longer forced on
// the line through this configuration parameter. If loop diagnostic procedures cannot be completed
// successfully after a vendordiscretionary number of retries or within a vendor-discretionary
// timeout, then an initialization failure occurs. (R, W, setbycreate) (mandatory) (1 byte)
//
// Automode Cold Start Forced
// Automode is defined as the case where multiple operation modes are enabled in xTSE (Table
// 9.7.12-1) and where the selection of the operation mode to be used for transmission depends, not
// only on the common capabilities of both xTUs (as exchanged in [ITU-T G.994.1]), but also on
// achievable data rates under given loop conditions. (R, W, setbycreate) (mandatory if automode is
// supported) (1 byte)
//
// L2 Atpr
// L2ATPR: This parameter specifies the maximum aggregate transmit power reduction that can be
// performed in the L2 request (i.e., at the transition of L0 to L2 state) or through a single
// power trim in the L2 state. It is only valid for [ITUT G.992.3], [ITUT G.992.4] and
// [ITUT G.992.5]. This attribute ranges from 0 (0 dB) dB to 31 (31 dB). (R, W, setbycreate)
// (mandatory) (1 byte)
//
// L2 Atprt
// L2ATPRT: This parameter specifies the total maximum aggregate transmit power reduction (in
// decibels) that can be performed in an L2 state. This is the sum of all reductions of L2 requests
// (i.e., at transitions from L0 to L2 state) and power trims. This attribute ranges from 0 (0 dB)
// dB to 31 (31 dB). (R, W, setbycreate) (mandatory) (1 byte)
//
// Force Inp Downstream
// Force INP downstream: When set to 1, the FORCEINPds attribute forces the framer settings of all
// downstream bearer channels to be selected such that the impulse noise protection (INP) computed
// according to the formula specified in the relevant Recommendation is greater than or equal to
// the minimal INP requirement. The default value 0 disables this function. (R, W) (mandatory for
// [ITU-T G.993.2], optional for other Recommendations that support it) (1 byte)
//
// Force Inp Upstream
// Force INP upstream: When set to 1, the FORCEINPus attribute forces the framer settings of all
// upstream bearer channels to be selected such that the INP computed according to the formula
// specified in the relevant Recommendation is greater than or equal to the minimal INP
// requirement. The default value 0 disables this function. (R, W) (mandatory for [ITU-T G.993.2],
// optional for other Recommendations that support it) (1 byte)
//
// Update Request Flag For Near_End Test Parameters
// Update request flag for near-end test parameters: The UPDATE-TEST-NE attribute forces an update
// of all near-end test parameters that can be updated during showtime in [ITU-T G.993.2]. Update
// is triggered by setting this attribute to 1, whereupon the near-end test parameters are expected
// to be updated within 10 s, and the ONU should reset the attribute value to 0. The update request
// flag is independent of any autonomous update process in the system. The update request attribute
// must be prepared to accept another set after a period not to exceed 3 min, a period that starts
// when the flag is set via the OMCI or by an autonomous process in the system. (R, W) (optional)
// (1 byte)
//
// Update Request Flag For Far_End Test Parameters
// Update request flag for far-end test parameters: The UPDATE-TEST-FE attribute forces an update
// of all far-end test parameters that can be updated during showtime in [ITU-T G.993.2]. Update is
// triggered by setting this attribute to 1, whereupon the far-end test parameters are expected to
// be updated within 10 s, and the ONU should reset the attribute value to 0. The update request
// flag is independent of any autonomous update process in the system. The update request attribute
// must be prepared to accept another set after a period not to exceed 3 min, a period that starts
// when the flag is set via the OMCI or by an autonomous process in the system. (R, W) (optional)
// (1 byte)
//
// Inm Inter Arrival Time Offset Upstream
// INM inter-arrival time offset upstream: INMIATOus is the inter-arrival time (IAT) offset that
// the xTU-C receiver uses to determine in which bin of the IAT histogram the IAT is reported.
// Valid values for INMIATO range from 3 to 511 discrete multi-tone (DMT) symbols in steps of 1 DMT
// symbol. (R, W) (optional) (2 bytes)
//
// Inm Inter_Arrival Time Step Upstream
// INM inter-arrival time step upstream: INMIATSus is the IAT step that the xTU-C receiver uses to
// determine in which bin of the IAT histogram the IAT is reported. Valid values for INMIATS range
// from 0 to 7 in steps of 1. (R, W) (optional) (1 byte)
//
// Inm Cluster Continuation Value Upstream
// INM cluster continuation value upstream: INMCCus is the cluster continuation value that the
// xTU-C receiver uses in the cluster indication process described in the applicable
// Recommendation. Valid values for INMCC range from 0 to 64 DMT symbols in steps of 1 DMT symbol.
// (R, W) (optional) (1 byte)
//
// Inm Equivalent Inp Mode Upstream
// INM equivalent INP mode upstream: INM_INPEQ_MODEus is the INM equivalent INP mode that the xTU-C
// receiver uses in the computation of the equivalent INP, as defined in the applicable
// Recommendation. Valid values for INM_INPEQ_MODE are 0..4. (R, W) (optional) (1 byte)
//
// Inm Inter Arrival Time Offset Downstream
// INM inter-arrival time offset downstream: INMIATOds is the IAT offset that the xTU-R receiver
// uses to determine in which bin of the IAT histogram the IAT is reported. Valid values for
// INMIATO range from 3 to 511 DMT symbols in steps of 1 DMT symbol. (R, W) (optional) (2 bytes)
//
// Inm Inter_Arrival Time Step Downstream
// INM inter-arrival time step downstream: INMIATSds is the IAT step that the xTU-R receiver uses
// to determine in which bin of the IAT histogram the IAT is reported. Valid values for INMIATS
// range from 0 to 7 in steps of 1. (R, W) (optional) (1 byte)
//
// Inm Cluster Continuation Value Downstream
// INM cluster continuation value downstream: INMCCds is the cluster continuation value that the
// xTU-R receiver uses in the cluster indication process described in the applicable
// Recommendation. Valid values for INMCC range from 0 to 64 DMT symbols in steps of 1 DMT symbol.
// (R, W) (optional) (1 byte)
//
// Inm Equivalent Inp Mode Downstream
// INM equivalent INP mode downstream: INM_INPEQ_MODEds is the INM equivalent INP mode that the
// xTU-R receiver uses in the computation of the equivalent INP, as defined in the applicable
// Recommendation. Valid values for INM_INPEQ_MODE are 0..4. (R, W) (optional) (1 byte)
//
type XdslLineConfigurationProfilePart3 struct {
ManagedEntityDefinition
Attributes AttributeValueMap
}
func init() {
xdsllineconfigurationprofilepart3BME = &ManagedEntityDefinition{
Name: "XdslLineConfigurationProfilePart3",
ClassID: 106,
MessageTypes: mapset.NewSetWith(
Create,
Delete,
Get,
Set,
),
AllowedAttributeMask: 0XFFFF,
AttributeDefinitions: AttributeDefinitionMap{
0: Uint16Field("ManagedEntityId", 0, mapset.NewSetWith(Read, SetByCreate), false, false, false, false, 0),
1: ByteField("LoopDiagnosticsModeForcedLdsf", 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, false, 1),
2: ByteField("AutomodeColdStartForced", 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, false, 2),
3: ByteField("L2Atpr", 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, false, 3),
4: ByteField("L2Atprt", 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, false, 4),
5: ByteField("ForceInpDownstream", 0, mapset.NewSetWith(Read, Write), false, false, false, false, 5),
6: ByteField("ForceInpUpstream", 0, mapset.NewSetWith(Read, Write), false, false, false, false, 6),
7: ByteField("UpdateRequestFlagForNearEndTestParameters", 0, mapset.NewSetWith(Read, Write), true, false, true, false, 7),
8: ByteField("UpdateRequestFlagForFarEndTestParameters", 0, mapset.NewSetWith(Read, Write), true, false, true, false, 8),
9: Uint16Field("InmInterArrivalTimeOffsetUpstream", 0, mapset.NewSetWith(Read, Write), false, false, true, false, 9),
10: ByteField("InmInterArrivalTimeStepUpstream", 0, mapset.NewSetWith(Read, Write), false, false, true, false, 10),
11: ByteField("InmClusterContinuationValueUpstream", 0, mapset.NewSetWith(Read, Write), false, false, true, false, 11),
12: ByteField("InmEquivalentInpModeUpstream", 0, mapset.NewSetWith(Read, Write), false, false, true, false, 12),
13: Uint16Field("InmInterArrivalTimeOffsetDownstream", 0, mapset.NewSetWith(Read, Write), false, false, true, false, 13),
14: ByteField("InmInterArrivalTimeStepDownstream", 0, mapset.NewSetWith(Read, Write), false, false, true, false, 14),
15: ByteField("InmClusterContinuationValueDownstream", 0, mapset.NewSetWith(Read, Write), false, false, true, false, 15),
16: ByteField("InmEquivalentInpModeDownstream", 0, mapset.NewSetWith(Read, Write), false, false, true, false, 16),
},
}
}
// NewXdslLineConfigurationProfilePart3 (class ID 106 creates the basic
// Managed Entity definition that is used to validate an ME of this type that
// is received from the wire, about to be sent on the wire.
func NewXdslLineConfigurationProfilePart3(params ...ParamData) (*ManagedEntity, OmciErrors) {
return NewManagedEntity(xdsllineconfigurationprofilepart3BME, params...)
}