| # Deployment configuration for a phyical hardware POD |
| --- |
| seedServer: |
| # IP address of the head node |
| ip: '10.90.0.2' |
| |
| # If the head node is being accessed via a tunnel or reponds to SSH on a non- |
| # standard port, the port value should be set. |
| # port: '2022' |
| |
| # User name and password used by Ansible to connect to the host for remote |
| # provisioning |
| user: 'ubuntu' |
| password: 'ubuntu' |
| |
| # Network address information for the head node: |
| # |
| # fabric_ip - the IP address and mask bits to be used to configure the network |
| # interface connected to the leaf - spine fabric |
| # |
| # management_ip - the IP address and mask bits to be used to configure the network |
| # interface connecting the head node to the POD internal |
| # management network. The head node will deliver DHCP addresses to |
| # the other compute nodes over this interface |
| # |
| # external_ip - the IP address and mask bits to be used to configure the network |
| # interface connecting the head node (and the POD) to the |
| # Internet. All traffic in the POD to external hosts will be |
| # NAT-ed through this interface |
| # external_iface - the name of the interface that connects the head node to the |
| # Internet |
| # management_network - the network and mask bits to used for hosts on the management |
| # network |
| fabric_ip: '10.6.1.1/24' |
| management_ip: '10.6.0.1/24' |
| external_ip: '47.135.132.21/24' |
| #external_iface: 'eth2' |
| management_network: 10.6.0.0/24 |
| |
| # the skipTags options allow various part of the deployment to be skipped |
| # switch_support - does not deploy switch boot images to the PXE server |
| # |
| # reboot - will not reboot the head node after updating its network configuration |
| # this may mean the network configuration will not take effect, but will |
| # also prevent you from being locked out of the server if there is a |
| # network configuration error. |
| # |
| # interface_config - will not modify the network configuration of the head node, |
| # including the consistent naming of the network interfaces |
| skipTags: |
| # - 'switch_support' |
| # - 'reboot' |
| # - 'interface_config' |
| |
| # The following variable settings can be used to customize how the network interfaces |
| # are selected into the fabric and management bridge interface or ignored/excluded. |
| # See the documentation docs/quickstart_physical.md for more information about how |
| # to set these variables. |
| extraVars: |
| # - 'fabric_include_names=<name1>,<name2>,...' |
| # - 'fabric_include_module_types=<mtype1>,<mtype2>,...' |
| # - 'fabric_include_bus_types=<btype1>,<btype2>,...' |
| # - 'fabric_exclude_names=<name1>,<name2>,...' |
| # - 'fabric_exclude_module_types=<mtype1>,<mtype2>,...' |
| # - 'fabric_exclude_bus_types=<btype1>,<btype2>,...' |
| # - 'fabric_ignore_names=<name1>,<name2>,...' |
| # - 'fabric_ignore_module_types=<mtype1>,<mtype2>,...' |
| # - 'fabric_ignore_bus_types=<btype1>,<btype2>,...' |
| # - 'management_include_names=<name1>,<name2>,...' |
| # - 'management_include_module_types=<mtype1>,<mtype2>,...' |
| # - 'management_include_bus_types=<btype1>,<btype2>,...' |
| # - 'management_exclude_names=<name1>,<name2>,...' |
| # - 'management_exclude_module_types=<mtype1>,<mtype2>,...' |
| # - 'management_exclude_bus_types=<btype1>,<btype2>,...' |
| # - 'management_ignore_names=<name1>,<name2>,...' |
| # - 'management_ignore_module_types=<mtype1>,<mtype2>,...' |
| # - 'management_ignore_bus_types=<btype1>,<btype2>,...' |
| |
| docker: |
| imageVersion: candidate |
| |
| otherNodes: |
| # Experimental |
| # |
| # Specifies the subnet and address range that will be used to allocate IP addresses |
| # to the compute nodes as they are deployed into the POD. |
| fabric: |
| network: 10.6.1.1/24 |
| management: 10.6.0.0/24 |
| range_low: 10.6.1.2 |
| range_high: 10.6.1.253 |