blob: caec656e07fa5ae66d7747bb277cb18a104b3a66 [file] [log] [blame]
# Copyright 2017-present Open Networking Foundation
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
# Deployment configuration for a phyical hardware POD
---
headnode:
ip: '10.90.0.2'
ansible_user: 'ubuntu'
ansible_ssh_pass: 'ubuntu'
ansible_ssh_port: 22
common:
# set to the profile of cord you want to install
cord_profile: 'rcord'
# cord dir is shared to corddev VM, causing permissions issues if these aren't set
credentials_dir: '/opt/credentials'
pki_dir: '/opt/pki'
ssh_pki_dir: '/opt/ssh_pki'
# Network address information for the head node:
#
# fabric_ip - the IP address and mask bits to be used to configure the network
# interface connected to the leaf - spine fabric
#
# management_ip - the IP address and mask bits to be used to configure the network
# interface connecting the head node to the POD internal
# management network. The head node will deliver DHCP addresses to
# the other compute nodes over this interface
#
# external_ip - the IP address and mask bits to be used to configure the network
# interface connecting the head node (and the POD) to the
# Internet. All traffic in the POD to external hosts will be
# NAT-ed through this interface
# external_iface - the name of the interface that connects the head node to the
# Internet
# management_network - the network and mask bits to used for hosts on the management
# network
fabric_ip: '10.6.1.1/24'
#fabric_range_low: '10.6.1.2'
#fabric_range_high: '10.6.1.100'
management_ip: '10.6.0.1/24'
#management_range_low: '10.6.0.2'
#management_range_high: '10.6.0.127'
external_ip: '47.135.132.21/24'
#external_iface: 'eth2'
management_network: 10.6.0.0/24
# the skipTags options allow various part of the deployment to be skipped
# switch_support - does not deploy switch boot images to the PXE server
#
# reboot - will not reboot the head node after updating its network configuration
# this may mean the network configuration will not take effect, but will
# also prevent you from being locked out of the server if there is a
# network configuration error.
#
# interface_config - will not modify the network configuration of the head node,
# including the consistent naming of the network interfaces
skipTags:
# - 'switch_support'
# - 'reboot'
# - 'interface_config'
# The following variable settings can be used to customize how the network interfaces
# are selected into the fabric and management bridge interface or ignored/excluded.
# See the documentation docs/quickstart_physical.md for more information about how
# to set these variables.
extraVars:
# - 'fabric_include_names=<name1>,<name2>,...'
# - 'fabric_include_module_types=<mtype1>,<mtype2>,...'
# - 'fabric_include_bus_types=<btype1>,<btype2>,...'
# - 'fabric_exclude_names=<name1>,<name2>,...'
# - 'fabric_exclude_module_types=<mtype1>,<mtype2>,...'
# - 'fabric_exclude_bus_types=<btype1>,<btype2>,...'
# - 'fabric_ignore_names=<name1>,<name2>,...'
# - 'fabric_ignore_module_types=<mtype1>,<mtype2>,...'
# - 'fabric_ignore_bus_types=<btype1>,<btype2>,...'
# - 'management_include_names=<name1>,<name2>,...'
# - 'management_include_module_types=<mtype1>,<mtype2>,...'
# - 'management_include_bus_types=<btype1>,<btype2>,...'
# - 'management_exclude_names=<name1>,<name2>,...'
# - 'management_exclude_module_types=<mtype1>,<mtype2>,...'
# - 'management_exclude_bus_types=<btype1>,<btype2>,...'
# - 'management_ignore_names=<name1>,<name2>,...'
# - 'management_ignore_module_types=<mtype1>,<mtype2>,...'
# - 'management_ignore_bus_types=<btype1>,<btype2>,...'
# - ubuntu_apt_repo="deb [arch=amd64] http://10.1.0.1:8889/mirror/archive.ubuntu.com/ubuntu trusty main universe"
# - ubuntu_updates_apt_repo="deb [arch=amd64] http://10.1.0.1:8889/mirror/archive.ubuntu.com/ubuntu trusty-updates main universe"
# - docker_apt_repo="deb [arch=amd64] http://10.1.0.1:8889/mirror/apt.dockerproject.org/repo ubuntu-trusty main"
# - java_apt_repo="deb [arch=amd64] http://10.1.0.1:8889/mirror/ppa.launchpad.net/webupd8team/java/ubuntu trusty main"
# - ansible_apt_repo="deb [arch=amd64] http://10.1.0.1:8889/mirror/ppa.launchpad.net/ansible/ansible/ubuntu trusty main"
# - maas_apt_repo="deb [arch=amd64] http://10.1.0.1:8889/mirror/ppa.launchpad.net/maas/stable/ubuntu trusty main"
# - dell_apt_repo="deb [arch=amd64] http://10.1.0.1:8889/mirror/linux.dell.com/repo/community trusty openmanage"
# - juju_apt_repo="deb [arch=amd64] http://10.1.0.1:8889/mirror/ppa.launchpad.net/juju/stable/ubuntu trusty main"
# If passwords are not set, random passwords will be generated
passwords:
#compute_node: ubuntu
#maas_admin: admin
#maas_user: cord
docker:
imageVersion: candidate