Once all the components needed for the SEBA profile are up and running on your POD, you will need to configure it. This is typically done using TOSCA.
In this page we are describing the process as a three steps process:
as that is what logically makes sense, but be aware that all the configurations can be unified in a single TOSCA file.
This configuration is environment specific, so you will need to create your own, but the following can serve as a reference:
tosca_definitions_version: tosca_simple_yaml_1_0 imports: - custom_types/switch.yaml - custom_types/switchport.yaml - custom_types/portinterface.yaml - custom_types/bngportmapping.yaml - custom_types/attworkflowdriverwhitelistentry.yaml - custom_types/attworkflowdriverservice.yaml - custom_types/serviceinstanceattribute.yaml - custom_types/onosapp.yaml description: Configures a full SEBA POD topology_template: node_templates: # Fabric configuration switch#leaf_1: type: tosca.nodes.Switch properties: driver: ofdpa3 ipv4Loopback: 192.168.0.201 ipv4NodeSid: 17 isEdgeRouter: True name: AGG_SWITCH ofId: of:0000000000000001 routerMac: 00:00:02:01:06:01 # Setup the OLT switch port port#olt_port: type: tosca.nodes.SwitchPort properties: portId: 1 host_learning: false requirements: - switch: node: switch#leaf_1 relationship: tosca.relationships.BelongsToOne # Port connected to the BNG port#bng_port: type: tosca.nodes.SwitchPort properties: portId: 31 requirements: - switch: node: switch#leaf_1 relationship: tosca.relationships.BelongsToOne # Setup the fabric switch port where the external # router is connected to bngmapping: type: tosca.nodes.BNGPortMapping properties: s_tag: any switch_port: 31 # DHCP L2 Relay config onos_app#dhcpl2relay: type: tosca.nodes.ONOSApp properties: name: dhcpl2relay must-exist: true dhcpl2relay-config-attr: type: tosca.nodes.ServiceInstanceAttribute properties: name: /onos/v1/network/configuration/apps/org.opencord.dhcpl2relay value: > { "dhcpl2relay" : { "useOltUplinkForServerPktInOut" : false, "dhcpServerConnectPoints" : [ "of:0000000000000001/31" ] } } requirements: - service_instance: node: onos_app#dhcpl2relay relationship: tosca.relationships.BelongsToOne
For instructions on how to push TOSCA into a CORD POD, please refer to this guide.
tosca_definitions_version: tosca_simple_yaml_1_0 imports: - custom_types/oltdevice.yaml - custom_types/onudevice.yaml - custom_types/voltservice.yaml description: Create an OLT Device in VOLTHA topology_template: node_templates: service#volt: type: tosca.nodes.VOLTService properties: name: volt must-exist: true olt_device: type: tosca.nodes.OLTDevice properties: name: My OLT device_type: openolt host: 10.90.0.122 port: 9191 switch_datapath_id: of:0000000000000002 # the openflow switch to which the OLT is connected switch_port: "1" # the port on the switch on which the OLT is connected outer_tpid: "0x8100" uplink: "65536" nas_id: "NAS_ID" serial_number: "10.90.0.122:9191" requirements: - volt_service: node: service#volt relationship: tosca.relationships.BelongsToOne
For instructions on how to push TOSCA into a CORD POD, please refer to this guide.
Once the POD has been configured, you can create a subscriber.
To create a subscriber, you'll need to know the serial number of the ONU it is attached to.
Once your POD is set up and the OLT has been pushed and activated in VOLTHA, XOS will discover the ONUs available in the system.
You can find them through:
vOLT > ONUDeviceshttp://<pod-id>:<chameleon-port|30006>/xosapi/v1/volt/onudevicesIf you are connected to the VOLTHA CLI you can use the following command to list all the existing devices:
(voltha) devices Devices: +------------------+--------------+------+------------------+-------------+-------------+----------------+----------------+------------------+----------+-------------------------+----------------------+------------------------------+ | id | type | root | parent_id | admin_state | oper_status | connect_status | parent_port_no | host_and_port | vendor_id| proxy_address.device_id | proxy_address.onu_id | proxy_address.onu_session_id | +------------------+--------------+------+------------------+-------------+-------------+----------------+----------------+------------------+----------+-------------------------+----------------------+------------------------------+ | 0001941bd45e71d8 | openolt | True | 000100000a5a0072 | ENABLED | ACTIVE | REACHABLE | | 10.90.0.114:9191 | | | | | | 00015698e67dc060 | broadcom_onu | True | 0001941bd45e71d8 | ENABLED | ACTIVE | REACHABLE | 536870912 | | BRCM| 0001941bd45e71d8 | 1 | 1 | +------------------+--------------+------+------------------+-------------+-------------+----------------+----------------+------------------+----------+-------------------------+----------------------+------------------------------+
Locate the correct ONU, then:
(voltha) device 00015698e67dc060 (device 00015698e67dc060) show Device 00015698e67dc060 +------------------------------+------------------+ | field | value | +------------------------------+------------------+ | id | 00015698e67dc060 | | type | broadcom_onu | | root | True | | parent_id | 0001941bd45e71d8 | | vendor | Broadcom | | model | n/a | | hardware_version | to be filled | | firmware_version | to be filled | | images.image | 1 item(s) | | serial_number | BRCM22222222 | +------------------------------+------------------+ | adapter | broadcom_onu | | admin_state | 3 | | oper_status | 4 | | connect_status | 2 | | proxy_address.device_id | 0001941bd45e71d8 | | proxy_address.onu_id | 1 | | proxy_address.onu_session_id | 1 | | parent_port_no | 536870912 | | vendor_id | BRCM | | ports | 2 item(s) | +------------------------------+------------------+ | flows.items | 5 item(s) | +------------------------------+------------------+
to find the correct serial number.
Once you have this information, you can create the subscriber by customizing the following TOSCA and passing it into the POD:
tosca_definitions_version: tosca_simple_yaml_1_0 imports: - custom_types/rcordsubscriber.yaml description: Create a test subscriber topology_template: node_templates: # A subscriber my_house: type: tosca.nodes.RCORDSubscriber properties: name: My House c_tag: 111 s_tag: 222 onu_device: BRCM1234 # Serial Number of the ONU Device to which this subscriber is connected
For instructions on how to push TOSCA into a CORD POD, please refer to this guide.