| /* |
| * Copyright (c) 2018 - present. Boling Consulting Solutions (bcsw.net) |
| * Copyright 2020-present Open Networking Foundation |
| |
| * Licensed under the Apache License, Version 2.0 (the "License"); |
| * you may not use this file except in compliance with the License. |
| * You may obtain a copy of the License at |
| |
| * http://www.apache.org/licenses/LICENSE-2.0 |
| |
| * Unless required by applicable law or agreed to in writing, software |
| * distributed under the License is distributed on an "AS IS" BASIS, |
| * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| * See the License for the specific language governing permissions and |
| * limitations under the License. |
| */ |
| /* |
| * NOTE: This file was generated, manual edits will be overwritten! |
| * |
| * Generated by 'goCodeGenerator.py': |
| * https://github.com/cboling/OMCI-parser/README.md |
| */ |
| |
| package generated |
| |
| import "github.com/deckarep/golang-set" |
| |
| // XdslChannelConfigurationProfileClassID is the 16-bit ID for the OMCI |
| // Managed entity xDSL channel configuration profile |
| const XdslChannelConfigurationProfileClassID = ClassID(107) // 0x006b |
| |
| var xdslchannelconfigurationprofileBME *ManagedEntityDefinition |
| |
| // XdslChannelConfigurationProfile (Class ID: #107 / 0x006b) |
| // This ME contains the channel configuration profile for an xDSL UNI. An instance of this ME is |
| // created and deleted by the OLT. |
| // |
| // NOTE - If [ITUT G.997.1] compatibility is required, bit rates should only be set to integer |
| // multiples of 1000-bits/s. The ONU may reject attempts to set other values for bit rate |
| // attributes. |
| // |
| // Relationships |
| // An instance of this ME may be associated with zero or more instances of the PPTP xDSL UNI part |
| // 1. |
| // |
| // Attributes |
| // Managed Entity Id |
| // This attribute uniquely identifies each instance of this ME. The value 0 is reserved. (R, |
| // setbycreate) (mandatory) (2-bytes) |
| // |
| // Minimum Data Rate |
| // This parameter specifies the minimum desired net data rate for the bearer channel. It is coded |
| // in bits per second. (R,-W, setbycreate) (mandatory) (4-bytes) |
| // |
| // Maximum Data Rate |
| // This parameter specifies the maximum desired net data rate for the bearer channel. It is coded |
| // in bits per second. (R,-W, setbycreate) (mandatory) (4-bytes) |
| // |
| // Rate Adaptation Ratio |
| // This attribute specifies the weight that should be taken into account when performing rate |
| // adaptation in the direction of the bearer channel. The attribute is defined as a percentage. The |
| // value 20, for example, means that 20% of the available data rate (in excess of the minimum data |
| // rate summed over all bearer channels) is assigned to this bearer channel and 80% to the other |
| // bearer channels. The OLT must ensure that the sum of rate adaptation ratios over all bearers in |
| // one direction is 100%. (R,-W, setbycreate) (optional) (1-byte) |
| // |
| // Maximum Interleaving Delay |
| // This attribute is the maximum one-way interleaving delay introduced by the PMS-TC between the |
| // alpha and the beta reference points, in the direction of the bearer channel. The one-way |
| // interleaving delay is defined in individual xDSL Recommendations as cap(S*D)-/4-ms, where S is |
| // the S factor, D is the interleaving depth, and cap() denotes rounding to the next higher |
| // integer. xTUs choose S and D values such that the actual one-way interleaving delay does not |
| // exceed the configured maximum interleaving delay. |
| // |
| // The delay is coded in milliseconds, varying from 2 to 63, with special meaning assigned to |
| // values 0, 1 and 255. The value 0 indicates that no delay bound is imposed. The value 1 indicates |
| // the fast latency path is to be used in the ITUT G.992.1 operating mode and S and D are to be |
| // selected such that S- 1 and D-= 1 in ITU-T G.992.2, ITUT G.992.3, ITUT G.992.4, ITUT G.992.5 and |
| // ITUT G.993.2 operating modes. The value 255 indicates a delay bound of 1-ms in ITUT-G.993.2 |
| // operation. (R,-W, setbycreate) (mandatory) (1-byte) |
| // |
| // Data Rate Threshold Upshift |
| // This attribute is a threshold on the cumulative data rate upshift achieved over one or more |
| // bearer channel data rate adaptations. An upshift rate change (DRT up) notification is issued by |
| // the PPTP xDSL UNI part 1 when the actual data rate exceeds the data rate at the last entry into |
| // showtime by more than the threshold. The data rate threshold is coded in bits per second. (R,-W, |
| // setbycreate) (mandatory for xDSL standards that use this attribute) (4-bytes) |
| // |
| // Data Rate Threshold Downshift |
| // This attribute is a threshold on the cumulative data rate downshift achieved over one or more |
| // bearer channel data rate adaptations. A downshift rate change (DRT down) notification is issued |
| // by the PPTP xDSL UNI part 1 when the actual data rate is below the data rate at the last entry |
| // into showtime by more than the threshold. The data rate threshold is coded in bits per second. |
| // (R,-W, setbycreate) (mandatory for xDSL standards that use this attribute) (4-bytes) |
| // |
| // Minimum Reserved Data Rate |
| // This attribute specifies the desired minimum reserved net data rate for the bearer channel. The |
| // rate is coded in bits per second. This attribute is needed only if the rate adaptation mode is |
| // set to dynamic in the xDSL line configuration profile part 1. (R,-W, setbycreate) (optional) |
| // (4-bytes) |
| // |
| // Minimum Data Rate In Low _ Power State |
| // Minimum data rate in low-power state: This parameter specifies the minimum desired net data rate |
| // for the bearer channel during the low-power state (L1/L2). The power management low-power states |
| // L1 and L2 are defined in [ITUT-G.992.2] and [ITUT G.992.3], respectively. The data rate is coded |
| // in bits per second. (R,-W, setbycreate) (mandatory) (4-byte) |
| // |
| // Minimum Impulse Noise Protection |
| // The INPmin attribute specifies the minimum INP for the bearer channel if it is transported over |
| // DMT symbols with a subcarrier spacing of 4.3125-kHz. INP is expressed in DMT symbols with a |
| // subcarrier spacing of 4.3125-kHz. It can be 1/2 symbol or any integer number of symbols from 0 |
| // to 16, inclusive. |
| // |
| // If the xTU does not support the configured INPmin value, it uses the nearest supported INP value |
| // greater than INPmin. |
| // |
| // Value INPmin |
| // |
| // 1 0 symbols |
| // |
| // 2 1/2 symbol |
| // |
| // N (N-- 2) symbols, 3 <= N <= 18 |
| // |
| // (R,-W, setbycreate) (optional for [ITU-T G.992.1], mandatory for other xDSL standards that use |
| // this attribute) (1-byte) |
| // |
| // Maximum Bit Error Ratio |
| // This attribute specifies the desired maximum bit error ratio for the bearer channel. It is only |
| // valid for [ITUT-G.992.3], [ITUT-G.992.4] and [ITUT-G.992.5]. The bit error ratio is specified |
| // via the following values: |
| // |
| // 1 10-3 |
| // |
| // 2 10-5 |
| // |
| // 3 10-7 |
| // |
| // (R,-W, setbycreate) (mandatory for standards that use this attribute) (1-byte) |
| // |
| // Minimum Impulse Noise Protection 8_Khz |
| // Minimum impulse noise protection 8-kHz: The INPmin8 attribute specifies the minimum INP for the |
| // bearer channel if it is transported over DMT symbols with a subcarrier spacing of 8.625-kHz. It |
| // is only valid for [ITUT-G.993.2]. INP is expressed in DMT symbols with a subcarrier spacing of |
| // 8.625-kHz. It can take any integer value from 0 (default) to 16, inclusive. (R, W) (mandatory |
| // for [ITUT-G.993.2]) (1 byte) |
| // |
| // Maximum Delay Variation |
| // The DVMAX attribute specifies the maximum value for delay variation allowed in an OLR procedure. |
| // Its value ranges from 1 (0.1-ms) to 254 (25.4-ms). The special value 255 specifies that no delay |
| // variation bound is imposed. (R, W) (optional: used by [ITUT-G.993.2]) (1 byte) |
| // |
| // Channel Initialization Policy Selection |
| // The CIPOLICY attribute specifies the policy to determine transceiver configuration at |
| // initialization. Valid values are 0..1, as defined in the Recommendations that use this |
| // attribute. (R,-W) (optional) (1-byte) |
| // |
| // Minimum Sos Bit Rate Downstream |
| // The MIN-SOS-BR-ds attribute specifies the minimum net data rate required for a valid SOS request |
| // in the downstream direction. The value is coded as an unsigned integer representing the data |
| // rate as a multiple of 8-kbit/s. (R,-W) (optional) (4-bytes) |
| // |
| // Minimum Sos Bit Rate Upstream |
| // The MIN-SOS-BR-us attribute specifies the minimum net data rate required for a valid SOS request |
| // in the upstream direction. The value is coded as an unsigned integer representing the data rate |
| // as a multiple of 8-kbit/s. (R,-W) (optional) (4-bytes) |
| // |
| type XdslChannelConfigurationProfile struct { |
| ManagedEntityDefinition |
| Attributes AttributeValueMap |
| } |
| |
| func init() { |
| xdslchannelconfigurationprofileBME = &ManagedEntityDefinition{ |
| Name: "XdslChannelConfigurationProfile", |
| ClassID: 107, |
| MessageTypes: mapset.NewSetWith( |
| Create, |
| Delete, |
| Get, |
| Set, |
| ), |
| AllowedAttributeMask: 0xfffe, |
| AttributeDefinitions: AttributeDefinitionMap{ |
| 0: Uint16Field("ManagedEntityId", PointerAttributeType, 0x0000, 0, mapset.NewSetWith(Read, SetByCreate), false, false, false, 0), |
| 1: Uint32Field("MinimumDataRate", UnsignedIntegerAttributeType, 0x8000, 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, 1), |
| 2: Uint32Field("MaximumDataRate", UnsignedIntegerAttributeType, 0x4000, 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, 2), |
| 3: ByteField("RateAdaptationRatio", UnsignedIntegerAttributeType, 0x2000, 0, mapset.NewSetWith(Read, SetByCreate, Write), false, true, false, 3), |
| 4: ByteField("MaximumInterleavingDelay", UnsignedIntegerAttributeType, 0x1000, 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, 4), |
| 5: Uint32Field("DataRateThresholdUpshift", UnsignedIntegerAttributeType, 0x0800, 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, 5), |
| 6: Uint32Field("DataRateThresholdDownshift", UnsignedIntegerAttributeType, 0x0400, 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, 6), |
| 7: Uint32Field("MinimumReservedDataRate", UnsignedIntegerAttributeType, 0x0200, 0, mapset.NewSetWith(Read, SetByCreate, Write), false, true, false, 7), |
| 8: Uint32Field("MinimumDataRateInLowPowerState", UnsignedIntegerAttributeType, 0x0100, 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, 8), |
| 9: ByteField("MinimumImpulseNoiseProtection", UnsignedIntegerAttributeType, 0x0080, 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, 9), |
| 10: ByteField("MaximumBitErrorRatio", UnsignedIntegerAttributeType, 0x0040, 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, 10), |
| 11: ByteField("MinimumImpulseNoiseProtection8Khz", UnsignedIntegerAttributeType, 0x0020, 0, mapset.NewSetWith(Read, Write), false, false, false, 11), |
| 12: ByteField("MaximumDelayVariation", UnsignedIntegerAttributeType, 0x0010, 0, mapset.NewSetWith(Read, Write), false, false, false, 12), |
| 13: ByteField("ChannelInitializationPolicySelection", UnsignedIntegerAttributeType, 0x0008, 0, mapset.NewSetWith(Read, Write), false, true, false, 13), |
| 14: Uint32Field("MinimumSosBitRateDownstream", UnsignedIntegerAttributeType, 0x0004, 0, mapset.NewSetWith(Read, Write), false, true, false, 14), |
| 15: Uint32Field("MinimumSosBitRateUpstream", UnsignedIntegerAttributeType, 0x0002, 0, mapset.NewSetWith(Read, Write), false, true, false, 15), |
| }, |
| Access: CreatedByOlt, |
| Support: UnknownSupport, |
| } |
| } |
| |
| // NewXdslChannelConfigurationProfile (class ID 107) creates the basic |
| // Managed Entity definition that is used to validate an ME of this type that |
| // is received from or transmitted to the OMCC. |
| func NewXdslChannelConfigurationProfile(params ...ParamData) (*ManagedEntity, OmciErrors) { |
| return NewManagedEntity(*xdslchannelconfigurationprofileBME, params...) |
| } |