agent/inband/scripts/start_inband_oltservices.sh - openolt - Gitiles

 #!/bin/bash

 #Copyright 2018-present Open Networking Foundation
 #
 #Licensed under the Apache License, Version 2.0 (the "License");
 #you may not use this file except in compliance with the License.
 #You may obtain a copy of the License at
 #
 #http://www.apache.org/licenses/LICENSE-2.0
 #
 #Unless required by applicable law or agreed to in writing, software
 #distributed under the License is distributed on an "AS IS" BASIS,
 #WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 #See the License for the specific language governing permissions and
 #limitations under the License.

 ### BEGIN INIT INFO
 # Provides:          start_inband_oltservices.sh
 # Required-Start:    $all
 # Required-Stop:     $network $local_fs $syslog
 # Default-Start:     2 3 4 5
 # Default-Stop:      0 1 6
 # Short-Description: Sets up inband management channel and starts device management and Openolt services
 # Description:
 #                    This script does the following things
 #                    1) Extracts bal package and keep the files in appropriate paths.
 #                    2) Starts svk_init which installs required drivers needed by the MAC devices
 #                    3) Starts device management daemon which initializes all maple, qumran chip sets
 #                       and brings up access terminal.
 #                    4) Sets up inband management channel
 #                    5) Creates inband vlan tagged interface which will be used to communicate to
 #                       Openolt service from vOLTHA via NNI
 #                    6) Sets up dhcp-client-identifier in "/etc/dhcp/dhclient.conf" for each inband
 #                       tagged interface so that it can obtain IP address from DHCP server
 #                    7) Sets up DHCP IP configuration in "/etc/network/interfaces" for inband tagged
 #                       interface so that it can initiate DHCPREQUEST to DHCP server once network
 #                       restart triggered.
 #                    8) Starts openolt service which enables all PON and NNI interfaces and creates
 #                       respective PON and NNI schedulers and Queues.
 ### END INIT INFO

 #------------------------------------------------------------------------------
 # GLOBAL VARIABLES
 #------------------------------------------------------------------------------

 # Root path where required bal directories are located
 BRCM_OPT_DIR='/opt/bcm68620'
 BRCM_DIR='/broadcom'

 # olt service files
 SVK_INIT_FILE="${BRCM_OPT_DIR}/svk_init.sh"

 # vlan config file
 VLAN_CONFIG_FILE="${BRCM_DIR}/vlan.config"
 DHCLIENT_CONF="/etc/dhcp/dhclient.conf"

 # olt serial number
 SERIAL_NUMBER="/sys/devices/virtual/dmi/id/product_serial"

 OLT_MODEL=$(cat /sys/devices/virtual/dmi/id/board_name)
 NETWORK_INTERFACE="/etc/network/interfaces"
 BAL_OPENOLT_DEB_16="/openolt_asfvolt16.deb"
 BAL_OPENOLT_DEB_64="/openolt_asgvolt64.deb"

 DEV_MGMT_DAEMON="dev_mgmt_daemon -d -pcie"
 OPENOLT="openolt"
 ASFVOLT16="asfvolt16"
 ASGVOLT64="asgvolt64"
 ASF16_MODEL="ASXvOLT16"

 # vlan id for asfvolt16
 ASFVOLT16_VLAN_ID_ETH2=

 # vlan id for asgvolt64
 ASGVOLT64_VLAN_ID_ETH1=

 # File used to set/get argument to openolt service
 OPENOLT_ARG_INPUT_FILE=/etc/default/openolt

 # Wait time for BAL to get ready
 WAIT_TIME_BAL_READY=20

 #------------------------------------------------------------------------------
 # Function Name: does_logger_exist
 # Description:
 #    This function check if logger exist and executable.
 #
 # Globals:
 #    None
 #
 # Arguments:
 #    None
 #
 # Returns:
 #    returns 0 if exist and executable else 1
 #------------------------------------------------------------------------------
 does_logger_exist() {
     cmd=/usr/bin/logger
     if [ -x ${cmd} ]; then
         return 0
     else
         return 1
     fi
 }

 #------------------------------------------------------------------------------
 # Function Name: info_message
 # Description:
 #    This function print the info message information to the console
 #
 # Globals:
 #    None
 #
 # Arguments:
 #    string message
 #
 # Returns:
 #    None
 #------------------------------------------------------------------------------
 info_message() {
     echo "INFO: $1"
     logger -p user.info "$1"
 }

 #------------------------------------------------------------------------------
 # Function Name: error_message
 # Description:
 #    This function print the error message information to the console
 #
 # Globals:
 #    None
 #
 # Arguments:
 #    string message
 #
 # Returns:
 #    returns 1
 #------------------------------------------------------------------------------
 error_message() {
     echo "ERROR: $1"
     logger -p user.err "$1"
     return 1
 }

 #------------------------------------------------------------------------------
 # Function Name: get_vlan_ids
 # Description:
 #    This function facilitates to fetch vlan id from vlan configuration file
 #    located at /broadcom/vlan.config
 #
 # Globals:
 #    VLAN_CONFIG_FILE, ASFVOLT16_VLAN_ID_ETH2, ASFVOLT16_VLAN_ID_ETH3,
 #    ASGVOLT64_VLAN_ID_ETH1, ASGVOLT64_VLAN_ID_ETH2
 #
 # Arguments:
 #    None
 #
 # Returns:
 #    None
 #------------------------------------------------------------------------------
 get_vlan_ids() {
     # Read vlan.config file to fetch vlan id information
     if [ -f ${VLAN_CONFIG_FILE} ]; then
         ASFVOLT16_VLAN_ID_ETH2=$(awk '/asfvolt16_vlan_id_eth2/{print $0}' ${VLAN_CONFIG_FILE} | awk -F "=" '{print $2}')
         ASGVOLT64_VLAN_ID_ETH1=$(awk '/asgvolt64_vlan_id_eth1/{print $0}' ${VLAN_CONFIG_FILE} | awk -F "=" '{print $2}')
         if [ -z ${ASFVOLT16_VLAN_ID_ETH2} ] || [ -z ${ASGVOLT64_VLAN_ID_ETH1} ]; then
             error_message "ERROR: vlan ids not valid"
             exit 1
         fi
     else
         error_message "ERROR: ${VLAN_CONFIG_FILE} not found, using default value 4093"
     fi
 }

 #------------------------------------------------------------------------------
 # Function Name: setup_nw_configuration
 # Description:
 #    This function read the "/broadcom/vlan.config" file to get VLAND IDs
 #    for the interface eth1 and eth2 based on the OLT model  and update
 #    these VLAN ID to /etc/network/interfaces file for dhcp request.
 # Globals:
 #    VLAN_CONFIG_FILE, ASFVOLT16_VLAN_ID_ETH2, ASGVOLT64_VLAN_ID_ETH1
 #
 # Arguments:
 #    None
 #
 # Returns:
 #    None
 #------------------------------------------------------------------------------
 setup_nw_configuration() {
     # Dynamic vlan entry in /etc/network/interfaces file
     # Should have only one entry in the file in case of multiple reboot
     if [ "${OLT_MODEL}" = ${ASF16_MODEL} ]; then
         set_dhcp_ip_configuration eth2 ${ASFVOLT16_VLAN_ID_ETH2}
     else
         set_dhcp_ip_configuration eth1 ${ASGVOLT64_VLAN_ID_ETH1}
     fi
     # Restart the networking services
     /etc/init.d/networking restart
 }

 #------------------------------------------------------------------------------
 # Function Name: set_dhcp_ip_configuration
 # Description:
 #    This function facilitates setup_nw_configuration function and accepts interface
 #    vlan id as an argumnet to modify network interfaces file
 #
 # Globals:
 #    None
 #
 # Arguments:
 #    None
 #
 # Returns:
 #    None
 #------------------------------------------------------------------------------
 set_dhcp_ip_configuration() {
     interface=$1
     vlan_id=$2
     grep -q "iface ${interface}.${vlan_id}" $NETWORK_INTERFACE
     if [ $? -ne 0 ]; then
         echo "auto ${interface}.${vlan_id}" >>${NETWORK_INTERFACE}
         echo "iface ${interface}.${vlan_id} inet dhcp" >>${NETWORK_INTERFACE}
     fi
 }

 #------------------------------------------------------------------------------
 # Function Name: start_dev_mgmt_service
 # Description:
 #    This function starts svk_init.sh script and device management service.
 #    Device management service initializes all maple, qumran chip sets and
 #    brings up access terminal.
 #
 # Globals:
 #    SVK_INIT_FILE, BRCM_DIR, DEV_MGMT_DAEMON
 #
 # Arguments:
 #    None
 #
 # Returns:
 #    None
 #------------------------------------------------------------------------------
 start_dev_mgmt_service() {
     info_message "Starting device management service"
     chmod +x ${SVK_INIT_FILE}
     ${SVK_INIT_FILE}

     # starts the device_management deamon and openolt services
     service dev_mgmt_daemon start
     service dev_mgmt_daemon status
     if [ $? -eq 0 ]; then
         info_message "${DEV_MGMT_DAEMON} service is running"
         setup_inband_mgmt_channel
     else
         error_message "${DEV_MGMT_DAEMON} is not running"
         exit 1
     fi
 }

 #------------------------------------------------------------------------------
 # Function Name: setup_inband_mgmt_channel
 # Description:
 #    This function sets up inband management channel.
 #
 # Globals:
 #    BRCM_DIR, ASFVOLT16_VLAN_ID_ETH2, ASGVOLT64_VLAN_ID_ETH1
 #
 # Arguments:
 #    None
 #
 # Returns:
 #    None
 #------------------------------------------------------------------------------
 setup_inband_mgmt_channel() {
     local interface_type="inband"

     # Extracting vlan ids from file
     get_vlan_ids

     cd ${BRCM_DIR}
     if [ "${OLT_MODEL}" = ${ASF16_MODEL} ]; then
         # Waiting till interface eth2 get initialized & RUNNING state
         check_interface_is_up eth2 $interface_type

         # wait for BAL to get ready
         sleep WAIT_TIME_BAL_READY

         # enabling in-band communication through broadcom API on NIC interface id 14 for eth2 interface
         echo "/Api/Set object=inband_mgmt_channel id=0 nni_intf={intf_type=nni intf_id=0} nic_intf_id=14 \
         vlan_id=${ASFVOLT16_VLAN_ID_ETH2} action=none" | ./example_user_appl
         if [ $? -ne 0 ]; then
             error_message "Failed to enable in-band channel on NIC interface id 14 with vlan ${ASFVOLT16_VLAN_ID_ETH2}"
         fi
     else
         # Waiting till interface eth1 get initialized & RUNNING state
         check_interface_is_up eth1 $interface_type
         # wait for BAL to get ready
         sleep WAIT_TIME_BAL_READY
         # enabling in-band communication through broadcom API on NIC interface id 14 for eth1 interface
         echo "/Api/Set object=inband_mgmt_channel id=0 nni_intf={intf_type=nni intf_id=0} nic_intf_id=14 \
         vlan_id=${ASGVOLT64_VLAN_ID_ETH1} action=none" | ./example_user_appl
         if [ $? -ne 0 ]; then
             error_message "Failed to enable in-band channel on NIC interface id 14 with vlan ${ASGVOLT64_VLAN_ID_ETH1}"
         fi
     fi
 }

 #------------------------------------------------------------------------------
 # Function Name: create_vlan_tagged_Iface
 # Description:
 #    This function create the VLAN interfaces and brings them UP.
 #
 # Globals:
 #    ASFVOLT16_VLAN_ID_ETH2, ASGVOLT64_VLAN_ID_ETH1
 #
 # Arguments:
 #    None
 #
 # Returns:
 #    None
 #------------------------------------------------------------------------------
 create_vlan_tagged_Iface() {
     if [ "${OLT_MODEL}" = ${ASF16_MODEL} ]; then
         # Adding vlan to the interface eth2
         ip link add link eth2 name eth2.${ASFVOLT16_VLAN_ID_ETH2} type vlan id ${ASFVOLT16_VLAN_ID_ETH2}
         ifconfig eth2.${ASFVOLT16_VLAN_ID_ETH2} up
     else
         # Adding vlan to the interface eth1
         ip link add link eth1 name eth1.${ASGVOLT64_VLAN_ID_ETH1} type vlan id ${ASGVOLT64_VLAN_ID_ETH1}
         ifconfig eth1.${ASGVOLT64_VLAN_ID_ETH1} up
     fi
     info_message "Inband tagged interfaces created succesfully"
 }

 #------------------------------------------------------------------------------
 # Function Name: setup_dhcpd_configuration
 # Description:
 #    This function updates /etc/dhcp/dhclient.conf file for dhcp
 #    request for eth2.ASFVOLT16_VLAN_ID_ETH2, eth3.ASFVOLT16_VLAN_ID_ETH3,
 #    eth1.ASGVOLT64_VLAN_ID_ETH1 and eth2.ASGVOLT64_VLAN_ID_ETH2 interfaces
 #
 # Globals:
 #    ASFVOLT16_VLAN_ID_ETH2, ASFVOLT16_VLAN_ID_ETH3, ASGVOLT64_VLAN_ID_ETH1,
 #    ASGVOLT64_VLAN_ID_ETH2,  DHCLIENT_CONF
 #
 # Arguments:
 #    None
 #
 # Returns:
 #    None
 #------------------------------------------------------------------------------
 setup_dhcpd_configuration() {
     if [ -f ${DHCLIENT_CONF} ]; then
         if [ -f ${SERIAL_NUMBER} ]; then
             serial_num=$(cat ${SERIAL_NUMBER})
             if [ "${OLT_MODEL}" = ${ASF16_MODEL} ]; then
                 # dhcient.conf file should have only one entry for eth2.<ASFVOLT16_VLAN_ID_ETH2> interface
                 set_dhclient_configuration eth2 ${ASFVOLT16_VLAN_ID_ETH2}
             else
                 # dhcient.conf file should have only one entry for eth1.<ASGVOLT64_VLAN_ID_ETH1> interface
                 set_dhclient_configuration eth1 ${ASGVOLT64_VLAN_ID_ETH1}
             fi
         else
             error_message "ERROR: serial number of olt not found"
         fi
     else
         error_message "ERROR: DHCP config file not found"
     fi
 }

 #------------------------------------------------------------------------------
 # Function Name: set_dhclient_configuration
 # Description:
 #    This function updates dhclient conf file with in-band interfaces.
 #
 # Globals:
 #    None
 #
 # Arguments:
 #    None
 #
 # Returns:
 #    None
 #------------------------------------------------------------------------------
 set_dhclient_configuration() {
     interface=$1
     vlan_id=$2
     grep -q "interface \"${interface}.${vlan_id}\"" $DHCLIENT_CONF
     if [ $? -ne 0 ]; then
         echo "interface \"${interface}.${vlan_id}\" {" >>$DHCLIENT_CONF
         echo "    send dhcp-client-identifier \"${serial_num}.${vlan_id}\";" >>$DHCLIENT_CONF
         echo "}" >>$DHCLIENT_CONF
     fi
 }

 #------------------------------------------------------------------------------
 # Function Name: check_interface_is_up
 # Description:
 #    This function checks if provided inband interface is up and running
 #
 # Globals:
 #    None
 #
 # Arguments:
 #    None
 #
 # Returns:
 #    None
 #------------------------------------------------------------------------------
 check_interface_is_up()
 {
     interface=$1
     interface_type=$2
     count=0

     while true; do
         if [ $interface_type = "inband" ]; then
             ifconfig ${interface} | grep 'RUNNING' &>/dev/null
             if [ $? -eq 0 ]; then
                 info_message "${interface} is up and running"
                 break
             fi
         elif [ $interface_type = "inband-tagged" ]; then
             while true; do
                 ifconfig ${interface} | grep 'RUNNING' &>/dev/null
                 if [ $? -eq 0 ]; then
                     ip=$(ifconfig $interface | grep "inet addr" | cut -d ':' -f 2 | cut -d ' ' -f 1)
                     if [ ! -z "$ip" ]; then
                         info_message "${interface} is up and running with valid IP address"
                         return 0
                     else
                         info_message "Inband interface ${interface} is not up, continuously retrying for DHCP IP assignment"
                         info_message "Inband interface ${interface} is not up with valid IP hence not starting openolt service"
                         sleep 10
                         continue
                     fi
                 fi
             done
         fi
     done
 }

 #------------------------------------------------------------------------------
 # Function Name: stop_olt_services
 # Description:
 #    This function informs about inband interface error status and stops device management service.
 #
 # Globals:
 #    None
 #
 # Arguments:
 #    None
 #
 # Returns:
 #    None
 #------------------------------------------------------------------------------
 stop_olt_services()
 {
     error_message "Inband tagged interface $1 is not up with valid IP address"
     info_message "Not starting openolt service and stopping device menagement service"
     service dev_mgmt_daemon stop
     exit 1
 }

 #------------------------------------------------------------------------------
 # Function Name: start_openolt_service
 # Description:
 #    This function checks whether inband interfaces are up with IP address, then
 #    appends inband interface name to a file which later will be used by openolt
 #    service as command line option then starts openolt service.
 #    Openolt service enables all PON and NNI interfaces and creates respective PON
 #    and NNI schedulers and Queues.
 #
 # Globals:
 #    None
 #
 # Arguments:
 #    None
 #
 # Returns:
 #    None
 #------------------------------------------------------------------------------
 start_openolt_service()
 {
     info_message "Starting openolt service"
     local interface_type="inband-tagged"

     if [ "${OLT_MODEL}" = ${ASF16_MODEL} ]; then
         check_interface_is_up eth2.${ASFVOLT16_VLAN_ID_ETH2} $interface_type
         if [ $? -ne 0 ]; then stop_olt_services eth2.${ASFVOLT16_VLAN_ID_ETH2}; fi
         openolt_grpc_interface=eth2.${ASFVOLT16_VLAN_ID_ETH2}
     else
         check_interface_is_up eth1.${ASGVOLT64_VLAN_ID_ETH1} $interface_type
         if [ $? -ne 0 ]; then stop_olt_services eth1.${ASGVOLT64_VLAN_ID_ETH1}; fi
         openolt_grpc_interface=eth1.${ASGVOLT64_VLAN_ID_ETH1}
     fi

     # Inband interface name appended to this file. Interface name will be
     # used as command line argument by openolt service while running the binary.
     if [ -f "$OPENOLT_ARG_INPUT_FILE" ]; then
         info_message "$OPENOLT_ARG_INPUT_FILE exist"
         echo "gRPC_interface=$openolt_grpc_interface" > $OPENOLT_ARG_INPUT_FILE
     else
         info_message "$OPENOLT_ARG_INPUT_FILE does not exist, creating it"
         touch $OPENOLT_ARG_INPUT_FILE
         echo "gRPC_interface=$openolt_grpc_interface" > $OPENOLT_ARG_INPUT_FILE
     fi

     service openolt start
     service openolt status
     if [ $? -eq 0 ]; then
         info_message "${OPENOLT} service is running"
     else
         error_message "${OPENOLT} is not running"
         exit 1
     fi
 }

 #------------------------------------------------------------------------------
 # Function Name: start_olt_services
 # Description:
 #    This function triggers services to create vlan interfaces, to run BAL services
 #    and to trigger DHCP requets on eth2.VLAN_ID_1 and eth3.VLAN_ID_2 interfaces.
 #
 # Globals:
 #    None
 #
 # Arguments:
 #    None
 #
 # Returns:
 #    None
 #------------------------------------------------------------------------------
 start_olt_services() {
     start_dev_mgmt_service
     create_vlan_tagged_Iface
     setup_dhcpd_configuration
     setup_nw_configuration
     start_openolt_service
 }

 #------------------------------------------------------------------------------
 # Function Name: copy_config_files
 # Description:
 #    This function copy config files to /broadcom directory
 #
 # Globals:
 #     BRCM_DIR
 #
 # Arguments:
 #    None
 #
 # Returns:
 #    None
 #------------------------------------------------------------------------------
 copy_config_files() {
     info_message "copying config files to ${BRCM_DIR}"
     # if [ "${OLT_MODEL}" != ${ASF16_MODEL} ]; then
     #     [ -f /qax.soc ] && cp "/qax.soc" "${BRCM_DIR}/"
     # fi
     # [ -f /config.bcm ] && cp "/config.bcm" "${BRCM_DIR}/"
     [ -f /vlan.config ] && cp "/vlan.config" "${BRCM_DIR}/"
 }

 # Execution starts from here
 does_logger_exist
 if [ $? -eq 0 ]; then
     if [ "${OLT_MODEL}" = ${ASF16_MODEL} ]; then
         # check if debian package is already installed.
         dpkg -l | grep ${ASFVOLT16}
         if [ $? -ne 0 ]; then
             # installs openolt debian package for asfvolt16 model
             dpkg -i ${BAL_OPENOLT_DEB_16}
         fi
     else
         dpkg -l | grep ${ASGVOLT64}
         if [ $? -ne 0 ]; then
             # installs openolt debian package for asgvolt64 model
             dpkg -i ${BAL_OPENOLT_DEB_64}
         fi
     fi
     copy_config_files
     start_olt_services
 else
     error_message "logger does not exist"
     exit 1
 fi
	#!/bin/bash

	#Copyright 2018-present Open Networking Foundation
	#
	#Licensed under the Apache License, Version 2.0 (the "License");
	#you may not use this file except in compliance with the License.
	#You may obtain a copy of the License at
	#
	#http://www.apache.org/licenses/LICENSE-2.0
	#
	#Unless required by applicable law or agreed to in writing, software
	#distributed under the License is distributed on an "AS IS" BASIS,
	#WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
	#See the License for the specific language governing permissions and
	#limitations under the License.

	### BEGIN INIT INFO
	# Provides: start_inband_oltservices.sh
	# Required-Start: $all
	# Required-Stop: $network $local_fs $syslog
	# Default-Start: 2 3 4 5
	# Default-Stop: 0 1 6
	# Short-Description: Sets up inband management channel and starts device management and Openolt services
	# Description:
	# This script does the following things
	# 1) Extracts bal package and keep the files in appropriate paths.
	# 2) Starts svk_init which installs required drivers needed by the MAC devices
	# 3) Starts device management daemon which initializes all maple, qumran chip sets
	# and brings up access terminal.
	# 4) Sets up inband management channel
	# 5) Creates inband vlan tagged interface which will be used to communicate to
	# Openolt service from vOLTHA via NNI
	# 6) Sets up dhcp-client-identifier in "/etc/dhcp/dhclient.conf" for each inband
	# tagged interface so that it can obtain IP address from DHCP server
	# 7) Sets up DHCP IP configuration in "/etc/network/interfaces" for inband tagged
	# interface so that it can initiate DHCPREQUEST to DHCP server once network
	# restart triggered.
	# 8) Starts openolt service which enables all PON and NNI interfaces and creates
	# respective PON and NNI schedulers and Queues.
	### END INIT INFO

	#------------------------------------------------------------------------------
	# GLOBAL VARIABLES
	#------------------------------------------------------------------------------

	# Root path where required bal directories are located
	BRCM_OPT_DIR='/opt/bcm68620'
	BRCM_DIR='/broadcom'

	# olt service files
	SVK_INIT_FILE="${BRCM_OPT_DIR}/svk_init.sh"

	# vlan config file
	VLAN_CONFIG_FILE="${BRCM_DIR}/vlan.config"
	DHCLIENT_CONF="/etc/dhcp/dhclient.conf"

	# olt serial number
	SERIAL_NUMBER="/sys/devices/virtual/dmi/id/product_serial"

	OLT_MODEL=$(cat /sys/devices/virtual/dmi/id/board_name)
	NETWORK_INTERFACE="/etc/network/interfaces"
	BAL_OPENOLT_DEB_16="/openolt_asfvolt16.deb"
	BAL_OPENOLT_DEB_64="/openolt_asgvolt64.deb"

	DEV_MGMT_DAEMON="dev_mgmt_daemon -d -pcie"
	OPENOLT="openolt"
	ASFVOLT16="asfvolt16"
	ASGVOLT64="asgvolt64"
	ASF16_MODEL="ASXvOLT16"

	# vlan id for asfvolt16
	ASFVOLT16_VLAN_ID_ETH2=

	# vlan id for asgvolt64
	ASGVOLT64_VLAN_ID_ETH1=

	# File used to set/get argument to openolt service
	OPENOLT_ARG_INPUT_FILE=/etc/default/openolt

	# Wait time for BAL to get ready
	WAIT_TIME_BAL_READY=20

	#------------------------------------------------------------------------------
	# Function Name: does_logger_exist
	# Description:
	# This function check if logger exist and executable.
	#
	# Globals:
	# None
	#
	# Arguments:
	# None
	#
	# Returns:
	# returns 0 if exist and executable else 1
	#------------------------------------------------------------------------------
	does_logger_exist() {
	cmd=/usr/bin/logger
	if [ -x ${cmd} ]; then
	return 0
	else
	return 1
	fi
	}

	#------------------------------------------------------------------------------
	# Function Name: info_message
	# Description:
	# This function print the info message information to the console
	#
	# Globals:
	# None
	#
	# Arguments:
	# string message
	#
	# Returns:
	# None
	#------------------------------------------------------------------------------
	info_message() {
	echo "INFO: $1"
	logger -p user.info "$1"
	}

	#------------------------------------------------------------------------------
	# Function Name: error_message
	# Description:
	# This function print the error message information to the console
	#
	# Globals:
	# None
	#
	# Arguments:
	# string message
	#
	# Returns:
	# returns 1
	#------------------------------------------------------------------------------
	error_message() {
	echo "ERROR: $1"
	logger -p user.err "$1"
	return 1
	}

	#------------------------------------------------------------------------------
	# Function Name: get_vlan_ids
	# Description:
	# This function facilitates to fetch vlan id from vlan configuration file
	# located at /broadcom/vlan.config
	#
	# Globals:
	# VLAN_CONFIG_FILE, ASFVOLT16_VLAN_ID_ETH2, ASFVOLT16_VLAN_ID_ETH3,
	# ASGVOLT64_VLAN_ID_ETH1, ASGVOLT64_VLAN_ID_ETH2
	#
	# Arguments:
	# None
	#
	# Returns:
	# None
	#------------------------------------------------------------------------------
	get_vlan_ids() {
	# Read vlan.config file to fetch vlan id information
	if [ -f ${VLAN_CONFIG_FILE} ]; then
	ASFVOLT16_VLAN_ID_ETH2=$(awk '/asfvolt16_vlan_id_eth2/{print $0}' ${VLAN_CONFIG_FILE} \| awk -F "=" '{print $2}')
	ASGVOLT64_VLAN_ID_ETH1=$(awk '/asgvolt64_vlan_id_eth1/{print $0}' ${VLAN_CONFIG_FILE} \| awk -F "=" '{print $2}')
	if [ -z ${ASFVOLT16_VLAN_ID_ETH2} ] \|\| [ -z ${ASGVOLT64_VLAN_ID_ETH1} ]; then
	error_message "ERROR: vlan ids not valid"
	exit 1
	fi
	else
	error_message "ERROR: ${VLAN_CONFIG_FILE} not found, using default value 4093"
	fi
	}

	#------------------------------------------------------------------------------
	# Function Name: setup_nw_configuration
	# Description:
	# This function read the "/broadcom/vlan.config" file to get VLAND IDs
	# for the interface eth1 and eth2 based on the OLT model and update
	# these VLAN ID to /etc/network/interfaces file for dhcp request.
	# Globals:
	# VLAN_CONFIG_FILE, ASFVOLT16_VLAN_ID_ETH2, ASGVOLT64_VLAN_ID_ETH1
	#
	# Arguments:
	# None
	#
	# Returns:
	# None
	#------------------------------------------------------------------------------
	setup_nw_configuration() {
	# Dynamic vlan entry in /etc/network/interfaces file
	# Should have only one entry in the file in case of multiple reboot
	if [ "${OLT_MODEL}" = ${ASF16_MODEL} ]; then
	set_dhcp_ip_configuration eth2 ${ASFVOLT16_VLAN_ID_ETH2}
	else
	set_dhcp_ip_configuration eth1 ${ASGVOLT64_VLAN_ID_ETH1}
	fi
	# Restart the networking services
	/etc/init.d/networking restart
	}

	#------------------------------------------------------------------------------
	# Function Name: set_dhcp_ip_configuration
	# Description:
	# This function facilitates setup_nw_configuration function and accepts interface
	# vlan id as an argumnet to modify network interfaces file
	#
	# Globals:
	# None
	#
	# Arguments:
	# None
	#
	# Returns:
	# None
	#------------------------------------------------------------------------------
	set_dhcp_ip_configuration() {
	interface=$1
	vlan_id=$2
	grep -q "iface ${interface}.${vlan_id}" $NETWORK_INTERFACE
	if [ $? -ne 0 ]; then
	echo "auto ${interface}.${vlan_id}" >>${NETWORK_INTERFACE}
	echo "iface ${interface}.${vlan_id} inet dhcp" >>${NETWORK_INTERFACE}
	fi
	}

	#------------------------------------------------------------------------------
	# Function Name: start_dev_mgmt_service
	# Description:
	# This function starts svk_init.sh script and device management service.
	# Device management service initializes all maple, qumran chip sets and
	# brings up access terminal.
	#
	# Globals:
	# SVK_INIT_FILE, BRCM_DIR, DEV_MGMT_DAEMON
	#
	# Arguments:
	# None
	#
	# Returns:
	# None
	#------------------------------------------------------------------------------
	start_dev_mgmt_service() {
	info_message "Starting device management service"
	chmod +x ${SVK_INIT_FILE}
	${SVK_INIT_FILE}

	# starts the device_management deamon and openolt services
	service dev_mgmt_daemon start
	service dev_mgmt_daemon status
	if [ $? -eq 0 ]; then
	info_message "${DEV_MGMT_DAEMON} service is running"
	setup_inband_mgmt_channel
	else
	error_message "${DEV_MGMT_DAEMON} is not running"
	exit 1
	fi
	}

	#------------------------------------------------------------------------------
	# Function Name: setup_inband_mgmt_channel
	# Description:
	# This function sets up inband management channel.
	#
	# Globals:
	# BRCM_DIR, ASFVOLT16_VLAN_ID_ETH2, ASGVOLT64_VLAN_ID_ETH1
	#
	# Arguments:
	# None
	#
	# Returns:
	# None
	#------------------------------------------------------------------------------
	setup_inband_mgmt_channel() {
	local interface_type="inband"

	# Extracting vlan ids from file
	get_vlan_ids

	cd ${BRCM_DIR}
	if [ "${OLT_MODEL}" = ${ASF16_MODEL} ]; then
	# Waiting till interface eth2 get initialized & RUNNING state
	check_interface_is_up eth2 $interface_type

	# wait for BAL to get ready
	sleep WAIT_TIME_BAL_READY

	# enabling in-band communication through broadcom API on NIC interface id 14 for eth2 interface
	echo "/Api/Set object=inband_mgmt_channel id=0 nni_intf={intf_type=nni intf_id=0} nic_intf_id=14 \
	vlan_id=${ASFVOLT16_VLAN_ID_ETH2} action=none" \| ./example_user_appl
	if [ $? -ne 0 ]; then
	error_message "Failed to enable in-band channel on NIC interface id 14 with vlan ${ASFVOLT16_VLAN_ID_ETH2}"
	fi
	else
	# Waiting till interface eth1 get initialized & RUNNING state
	check_interface_is_up eth1 $interface_type
	# wait for BAL to get ready
	sleep WAIT_TIME_BAL_READY
	# enabling in-band communication through broadcom API on NIC interface id 14 for eth1 interface
	echo "/Api/Set object=inband_mgmt_channel id=0 nni_intf={intf_type=nni intf_id=0} nic_intf_id=14 \
	vlan_id=${ASGVOLT64_VLAN_ID_ETH1} action=none" \| ./example_user_appl
	if [ $? -ne 0 ]; then
	error_message "Failed to enable in-band channel on NIC interface id 14 with vlan ${ASGVOLT64_VLAN_ID_ETH1}"
	fi
	fi
	}

	#------------------------------------------------------------------------------
	# Function Name: create_vlan_tagged_Iface
	# Description:
	# This function create the VLAN interfaces and brings them UP.
	#
	# Globals:
	# ASFVOLT16_VLAN_ID_ETH2, ASGVOLT64_VLAN_ID_ETH1
	#
	# Arguments:
	# None
	#
	# Returns:
	# None
	#------------------------------------------------------------------------------
	create_vlan_tagged_Iface() {
	if [ "${OLT_MODEL}" = ${ASF16_MODEL} ]; then
	# Adding vlan to the interface eth2
	ip link add link eth2 name eth2.${ASFVOLT16_VLAN_ID_ETH2} type vlan id ${ASFVOLT16_VLAN_ID_ETH2}
	ifconfig eth2.${ASFVOLT16_VLAN_ID_ETH2} up
	else
	# Adding vlan to the interface eth1
	ip link add link eth1 name eth1.${ASGVOLT64_VLAN_ID_ETH1} type vlan id ${ASGVOLT64_VLAN_ID_ETH1}
	ifconfig eth1.${ASGVOLT64_VLAN_ID_ETH1} up
	fi
	info_message "Inband tagged interfaces created succesfully"
	}

	#------------------------------------------------------------------------------
	# Function Name: setup_dhcpd_configuration
	# Description:
	# This function updates /etc/dhcp/dhclient.conf file for dhcp
	# request for eth2.ASFVOLT16_VLAN_ID_ETH2, eth3.ASFVOLT16_VLAN_ID_ETH3,
	# eth1.ASGVOLT64_VLAN_ID_ETH1 and eth2.ASGVOLT64_VLAN_ID_ETH2 interfaces
	#
	# Globals:
	# ASFVOLT16_VLAN_ID_ETH2, ASFVOLT16_VLAN_ID_ETH3, ASGVOLT64_VLAN_ID_ETH1,
	# ASGVOLT64_VLAN_ID_ETH2, DHCLIENT_CONF
	#
	# Arguments:
	# None
	#
	# Returns:
	# None
	#------------------------------------------------------------------------------
	setup_dhcpd_configuration() {
	if [ -f ${DHCLIENT_CONF} ]; then
	if [ -f ${SERIAL_NUMBER} ]; then
	serial_num=$(cat ${SERIAL_NUMBER})
	if [ "${OLT_MODEL}" = ${ASF16_MODEL} ]; then
	# dhcient.conf file should have only one entry for eth2.<ASFVOLT16_VLAN_ID_ETH2> interface
	set_dhclient_configuration eth2 ${ASFVOLT16_VLAN_ID_ETH2}
	else
	# dhcient.conf file should have only one entry for eth1.<ASGVOLT64_VLAN_ID_ETH1> interface
	set_dhclient_configuration eth1 ${ASGVOLT64_VLAN_ID_ETH1}
	fi
	else
	error_message "ERROR: serial number of olt not found"
	fi
	else
	error_message "ERROR: DHCP config file not found"
	fi
	}

	#------------------------------------------------------------------------------
	# Function Name: set_dhclient_configuration
	# Description:
	# This function updates dhclient conf file with in-band interfaces.
	#
	# Globals:
	# None
	#
	# Arguments:
	# None
	#
	# Returns:
	# None
	#------------------------------------------------------------------------------
	set_dhclient_configuration() {
	interface=$1
	vlan_id=$2
	grep -q "interface \"${interface}.${vlan_id}\"" $DHCLIENT_CONF
	if [ $? -ne 0 ]; then
	echo "interface \"${interface}.${vlan_id}\" {" >>$DHCLIENT_CONF
	echo " send dhcp-client-identifier \"${serial_num}.${vlan_id}\";" >>$DHCLIENT_CONF
	echo "}" >>$DHCLIENT_CONF
	fi
	}

	#------------------------------------------------------------------------------
	# Function Name: check_interface_is_up
	# Description:
	# This function checks if provided inband interface is up and running
	#
	# Globals:
	# None
	#
	# Arguments:
	# None
	#
	# Returns:
	# None
	#------------------------------------------------------------------------------
	check_interface_is_up()
	{
	interface=$1
	interface_type=$2
	count=0

	while true; do
	if [ $interface_type = "inband" ]; then
	ifconfig ${interface} \| grep 'RUNNING' &>/dev/null
	if [ $? -eq 0 ]; then
	info_message "${interface} is up and running"
	break
	fi
	elif [ $interface_type = "inband-tagged" ]; then
	while true; do
	ifconfig ${interface} \| grep 'RUNNING' &>/dev/null
	if [ $? -eq 0 ]; then
	ip=$(ifconfig $interface \| grep "inet addr" \| cut -d ':' -f 2 \| cut -d ' ' -f 1)
	if [ ! -z "$ip" ]; then
	info_message "${interface} is up and running with valid IP address"
	return 0
	else
	info_message "Inband interface ${interface} is not up, continuously retrying for DHCP IP assignment"
	info_message "Inband interface ${interface} is not up with valid IP hence not starting openolt service"
	sleep 10
	continue
	fi
	fi
	done
	fi
	done
	}

	#------------------------------------------------------------------------------
	# Function Name: stop_olt_services
	# Description:
	# This function informs about inband interface error status and stops device management service.
	#
	# Globals:
	# None
	#
	# Arguments:
	# None
	#
	# Returns:
	# None
	#------------------------------------------------------------------------------
	stop_olt_services()
	{
	error_message "Inband tagged interface $1 is not up with valid IP address"
	info_message "Not starting openolt service and stopping device menagement service"
	service dev_mgmt_daemon stop
	exit 1
	}

	#------------------------------------------------------------------------------
	# Function Name: start_openolt_service
	# Description:
	# This function checks whether inband interfaces are up with IP address, then
	# appends inband interface name to a file which later will be used by openolt
	# service as command line option then starts openolt service.
	# Openolt service enables all PON and NNI interfaces and creates respective PON
	# and NNI schedulers and Queues.
	#
	# Globals:
	# None
	#
	# Arguments:
	# None
	#
	# Returns:
	# None
	#------------------------------------------------------------------------------
	start_openolt_service()
	{
	info_message "Starting openolt service"
	local interface_type="inband-tagged"

	if [ "${OLT_MODEL}" = ${ASF16_MODEL} ]; then
	check_interface_is_up eth2.${ASFVOLT16_VLAN_ID_ETH2} $interface_type
	if [ $? -ne 0 ]; then stop_olt_services eth2.${ASFVOLT16_VLAN_ID_ETH2}; fi
	openolt_grpc_interface=eth2.${ASFVOLT16_VLAN_ID_ETH2}
	else
	check_interface_is_up eth1.${ASGVOLT64_VLAN_ID_ETH1} $interface_type
	if [ $? -ne 0 ]; then stop_olt_services eth1.${ASGVOLT64_VLAN_ID_ETH1}; fi
	openolt_grpc_interface=eth1.${ASGVOLT64_VLAN_ID_ETH1}
	fi

	# Inband interface name appended to this file. Interface name will be
	# used as command line argument by openolt service while running the binary.
	if [ -f "$OPENOLT_ARG_INPUT_FILE" ]; then
	info_message "$OPENOLT_ARG_INPUT_FILE exist"
	echo "gRPC_interface=$openolt_grpc_interface" > $OPENOLT_ARG_INPUT_FILE
	else
	info_message "$OPENOLT_ARG_INPUT_FILE does not exist, creating it"
	touch $OPENOLT_ARG_INPUT_FILE
	echo "gRPC_interface=$openolt_grpc_interface" > $OPENOLT_ARG_INPUT_FILE
	fi

	service openolt start
	service openolt status
	if [ $? -eq 0 ]; then
	info_message "${OPENOLT} service is running"
	else
	error_message "${OPENOLT} is not running"
	exit 1
	fi
	}

	#------------------------------------------------------------------------------
	# Function Name: start_olt_services
	# Description:
	# This function triggers services to create vlan interfaces, to run BAL services
	# and to trigger DHCP requets on eth2.VLAN_ID_1 and eth3.VLAN_ID_2 interfaces.
	#
	# Globals:
	# None
	#
	# Arguments:
	# None
	#
	# Returns:
	# None
	#------------------------------------------------------------------------------
	start_olt_services() {
	start_dev_mgmt_service
	create_vlan_tagged_Iface
	setup_dhcpd_configuration
	setup_nw_configuration
	start_openolt_service
	}

	#------------------------------------------------------------------------------
	# Function Name: copy_config_files
	# Description:
	# This function copy config files to /broadcom directory
	#
	# Globals:
	# BRCM_DIR
	#
	# Arguments:
	# None
	#
	# Returns:
	# None
	#------------------------------------------------------------------------------
	copy_config_files() {
	info_message "copying config files to ${BRCM_DIR}"
	# if [ "${OLT_MODEL}" != ${ASF16_MODEL} ]; then
	# [ -f /qax.soc ] && cp "/qax.soc" "${BRCM_DIR}/"
	# fi
	# [ -f /config.bcm ] && cp "/config.bcm" "${BRCM_DIR}/"
	[ -f /vlan.config ] && cp "/vlan.config" "${BRCM_DIR}/"
	}

	# Execution starts from here
	does_logger_exist
	if [ $? -eq 0 ]; then
	if [ "${OLT_MODEL}" = ${ASF16_MODEL} ]; then
	# check if debian package is already installed.
	dpkg -l \| grep ${ASFVOLT16}
	if [ $? -ne 0 ]; then
	# installs openolt debian package for asfvolt16 model
	dpkg -i ${BAL_OPENOLT_DEB_16}
	fi
	else
	dpkg -l \| grep ${ASGVOLT64}
	if [ $? -ne 0 ]; then
	# installs openolt debian package for asgvolt64 model
	dpkg -i ${BAL_OPENOLT_DEB_64}
	fi
	fi
	copy_config_files
	start_olt_services
	else
	error_message "logger does not exist"
	exit 1
	fi