blob: 0a7df4af5633a419dcda60224268bf66346ffdf1 [file] [log] [blame]
You Wang3e6beac2017-08-31 15:12:13 -07001
2# Copyright 2017-present Open Networking Foundation
3#
4# Licensed under the Apache License, Version 2.0 (the "License");
5# you may not use this file except in compliance with the License.
6# You may obtain a copy of the License at
7#
8# http://www.apache.org/licenses/LICENSE-2.0
9#
10# Unless required by applicable law or agreed to in writing, software
11# distributed under the License is distributed on an "AS IS" BASIS,
12# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
13# See the License for the specific language governing permissions and
14# limitations under the License.
15
16
Luca Prete14a44062017-05-08 15:52:53 -070017# Deployment configuration for a physical hardware POD
18---
19
20# this is used to generate the genconfig/cord-inv file
21headnode:
You Wang8d0bfb22017-08-31 16:49:16 -070022 ip: '10.192.4.62'
Luca Prete14a44062017-05-08 15:52:53 -070023 ansible_user: 'cord'
24 ansible_ssh_pass: 'cord'
25 ansible_ssh_port: 22
26
27common:
28 # set to the profile of cord you want to install
29 cord_profile: 'rcord'
30
Andy Bavier2218a722017-07-12 14:21:58 -070031 # cord dir is shared to corddev VM, causing permissions issues if these aren't set
32 credentials_dir: '/opt/credentials'
33 pki_dir: '/opt/pki'
34 ssh_pki_dir: '/opt/ssh_pki'
Luca Prete14a44062017-05-08 15:52:53 -070035
36 # all of these are written to genconfig/config.yml, and needs a rework
37
38 # Network address information for the head node:
39 #
40 # fabric_ip - the IP address and mask bits to be used to configure the network
41 # interface connected to the leaf - spine fabric
42 #
43 # management_ip - the IP address and mask bits to be used to configure the network
44 # interface connecting the head node to the POD internal
45 # management network. The head node will deliver DHCP addresses to
46 # the other compute nodes over this interface
47 #
48 # external_ip - the IP address and mask bits to be used to configure the network
49 # interface connecting the head node (and the POD) to the
50 # Internet. All traffic in the POD to external hosts will be
51 # NAT-ed through this interface
52 fabric_ip: '10.6.1.1/24'
53 management_ip: '10.6.0.1/24'
You Wang8d0bfb22017-08-31 16:49:16 -070054 external_ip: '10.192.4.62/20'
55 external_iface: 'enp4s0f1'
56 external_gw: '10.192.4.1'
Luca Prete14a44062017-05-08 15:52:53 -070057 skipTags:
58
59passwords:
60 compute_node: "ubuntu"
61 maas_admin: "admin"
62 maas_user: "cord"
63
64docker:
65 imageVersion: candidate
66
67otherNodes:
68 # Experimental
69 #
70 # Specifies the subnet and address range that will be used to allocate IP addresses
71 # to the compute nodes as they are deployed into the POD.
72 fabric:
73 network: 10.6.1.1/24
74 range_low: 10.6.1.2
75 range_high: 10.6.1.253