| |
| Zebra OSPF daemon for IPv6 network |
| |
| 2003/08/18 |
| |
| README for newer code is not yet. General usage should remain |
| the same. For further usage, see command helps by typing '?' |
| in vty, and then imagin ! ;p) Previous README contents follows. |
| |
| Zebra OSPF daemon for IPv6 network |
| |
| 2001/12/20 |
| |
| Zebra OSPF6d is OSPF version 3 daemon which is specified by |
| "OSPF for IPv6" (RFC 2740). |
| |
| *** NOTE *** |
| Zebra ospf6d is in development yet. It may lack some functionalities, |
| and may have some bugs. Use the latest version from the anoncvs |
| repository (http://www.zebra.org/cvs.html) ! |
| |
| This file README is like memo yet, so please feel free to ask |
| <yasu@sfc.wide.ad.jp> by E-mail. Patches will be appriciated. |
| |
| ospf6d's vty port was default to 2606/tcp. |
| Use commands below. |
| |
| VIEW NODE: |
| show ipv6 ospf6 |
| To see Router-ID, uptime of ospf6d, some statistics. |
| |
| show ipv6 ospf6 database ... |
| This command shows LSA database. You can specify |
| LS-type/LS-ID/Advertising-Router of LSAs. '*' is recognized. |
| |
| show ipv6 ospf6 interface ... |
| To see the status of the OSPF interface, and the configuration |
| like interface costs. |
| |
| show ipv6 ospf6 neighbor ... |
| Shows state of neighbors and choosed (Backup) DR on the I/F. |
| |
| show ipv6 ospf6 route (X::X) |
| This command shows internal routing table of the ospf6d. |
| Routes not calculated by OSPFv3 (like connected routes) |
| are not shown. If Address is specified (X::X), shows the route |
| that the address matches. |
| |
| show ipv6 ospf6 route redistribute (X::X) |
| Shows the routes advertised as AS-External routes by the router |
| itself. If Address is specified (X::X), shows the route |
| that the address matches. |
| |
| CONFIG NODE: |
| interface NAME |
| To enter INTERFACE NODE |
| |
| router ospf6 ... |
| To enter OSPF6 NODE |
| |
| INTERFACE NODE: |
| ipv6 ospf6 cost COST |
| Sets the interface's output cost. Depends on interface bandwidth by default. |
| |
| ipv6 ospf6 hello-interval HELLOINTERVAL |
| Sets the interface's Hello Interval. default 10 |
| |
| ipv6 ospf6 dead-interval DEADINTERVAL |
| Sets the interface's Router Dead Interval. default 40 |
| |
| ipv6 ospf6 retransmit-interval RETRANSMITINTERVAL |
| Sets the interface's Rxmt Interval. default 5 |
| |
| ipv6 ospf6 priority PRIORITY |
| Sets the interface's Router Priority. default 1 |
| |
| ipv6 ospf6 transmit-delay TRANSMITDELAY |
| Sets the interface's Inf-Trans-Delay. default 1 |
| |
| OSPF6 NODE: |
| router-id A.B.C.D |
| Sets the router's Router-ID |
| |
| interface NAME area AREA |
| Binds interface to specified Area, and start |
| sending OSPFv3 packets. |
| |
| auto-cost reference-bandwidth COST |
| Sets the reference bandwidth for cost calculations, where this |
| bandwidth is considered equivalent to an OSPF cost of 1, specified |
| in Mbits/s. The default is 100Mbit/s (i.e. a link of bandwidth |
| 100Mbit/s or higher will have a cost of 1. Cost of lower bandwidth |
| links will be scaled with reference to this cost). This |
| configuration setting MUST be consistent across all routers within |
| the OSPF domain. |
| |
| Sample configuration is in ospf6d.conf.sample. |
| |
| -- |
| Yasuhiro Ohara <yasu@sfc.wide.ad.jp> |
| Kunihiro Ishiguro <kunihiro@zebra.org> |
| |