| @node OSPFv2, OSPFv3, RIPng, Top |
| @comment node-name, next, previous, up |
| @chapter OSPFv2 |
| |
| OSPF version 2 is a routing protocol which described in |
| @asis{RFC2328} - @cite{OSPF Version 2}. OSPF is IGP (Interior Gateway |
| Protocols). Compared with RIP, OSPF can provide scalable network |
| support and faster convergence time. OSPF is widely used in large |
| networks such as ISP backbone and enterprise networks. |
| |
| @menu |
| * Configuring ospfd:: |
| * OSPF router:: |
| * OSPF area:: |
| * OSPF interface:: |
| * Redistribute routes to OSPF:: |
| * Showing OSPF information:: |
| * Debugging OSPF:: |
| @end menu |
| |
| @node Configuring ospfd, OSPF router, OSPFv2, OSPFv2 |
| @comment node-name, next, previous, up |
| @section Configuring ospfd |
| |
| There is no @command{ospfd} specific options. Common options can be |
| specified (@pxref{Common Invocation Options}) to @command{ospfd}. |
| @command{ospfd} needs interface information from @command{zebra}. So |
| please make it sure @command{zebra} is running before invoking |
| @command{ospfd}. |
| |
| Like other daemons, @command{ospfd} configuration is done in OSPF |
| specific configuration file @file{ospfd.conf}. |
| |
| @node OSPF router, OSPF area, Configuring ospfd, OSPFv2 |
| @comment node-name, next, previous, up |
| @section OSPF router |
| |
| To start OSPF process you have to specify the OSPF router. As of this |
| writing, @command{ospfd} does not support multiple OSPF processes. |
| |
| @deffn Command {router ospf} {} |
| @deffnx Command {no router ospf} {} |
| Enable or disable the OSPF process. @command{ospfd} does not yet |
| support multiple OSPF processes. So you can not specify an OSPF process |
| number. |
| @end deffn |
| |
| @deffn {OSPF Command} {ospf router-id @var{a.b.c.d}} {} |
| @deffnx {OSPF Command} {no ospf router-id} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {ospf abr-type @var{type}} {} |
| @deffnx {OSPF Command} {no ospf abr-type @var{type}} {} |
| @var{type} can be cisco|ibm|shortcut|standard |
| More information regarding the behaviour controlled by this command can |
| be found in draft-ietf-ospf-abr-alt-05.txt and |
| draft-ietf-ospf-shortcut-abr-02.txt |
| Quote: "Though the definition of the Area Border Router (ABR) |
| in the OSPF specification does not require a router with multiple |
| attached areas to have a backbone connection, it is actually |
| necessary to provide successful routing to the inter-area and |
| external destinations. If this requirement is not met, all traffic |
| destined for the areas not connected to such an ABR or out of the |
| OSPF domain, is dropped. This document describes alternative ABR |
| behaviors implemented in Cisco and IBM routers." |
| @end deffn |
| |
| @deffn {OSPF Command} {ospf rfc1583compatibility} {} |
| @deffnx {OSPF Command} {no ospf rfc1583compatibility} {} |
| This rfc2328, the sucessor to rfc1583, suggests according to section G.2 |
| (changes) in section 16.4 a change to the path preference algorithm that |
| prevents possible routing loops that were possible in the old version of |
| OSPFv2. More specificly it demands that inter-area paths and intra-area path |
| are now of equal preference but still both preferred to external paths. |
| @end deffn |
| |
| @deffn {OSPF Command} {passive interface @var{interface}} {} |
| @deffnx {OSPF Command} {no passive interface @var{interface}} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {timers spf <0-4294967295> <0-4294967295>} {} |
| @deffnx {OSPF Command} {no timers spf} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {refresh group-limit <0-10000>} {} |
| @deffnx {OSPF Command} {refresh per-slice <0-10000>} {} |
| @deffnx {OSPF Command} {refresh age-diff <0-10000>} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {auto-cost refrence-bandwidth <1-4294967>} {} |
| @deffnx {OSPF Command} {no auto-cost refrence-bandwidth} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {network @var{a.b.c.d/m} area @var{a.b.c.d}} {} |
| @deffnx {OSPF Command} {network @var{a.b.c.d/m} area @var{<0-4294967295>}} {} |
| @deffnx {OSPF Command} {no network @var{a.b.c.d/m} area @var{a.b.c.d}} {} |
| @deffnx {OSPF Command} {no network @var{a.b.c.d/m} area @var{<0-4294967295>}} {} |
| This command specifies the OSPF enabled interface. If the interface has |
| an address of 10.0.0.1/8 then the command below provides network |
| information to the ospf routers |
| @example |
| @group |
| router ospf |
| network 10.0.0.0/8 area 0 |
| @end group |
| @end example |
| the network command's mask length should be the same as the interface |
| address's mask. |
| @end deffn |
| |
| @node OSPF area, OSPF interface, OSPF router, OSPFv2 |
| @comment node-name, next, previous, up |
| @section OSPF area |
| |
| @deffn {OSPF Command} {area @var{a.b.c.d} range @var{a.b.c.d/m}} {} |
| @deffnx {OSPF Command} {area <0-4294967295> range @var{a.b.c.d/m}} {} |
| @deffnx {OSPF Command} {no area @var{a.b.c.d} range @var{a.b.c.d/m}} {} |
| @deffnx {OSPF Command} {no area <0-4294967295> range @var{a.b.c.d/m}} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {area @var{a.b.c.d} range IPV4_PREFIX suppress} {} |
| @deffnx {OSPF Command} {no area @var{a.b.c.d} range IPV4_PREFIX suppress} {} |
| @deffnx {OSPF Command} {area @var{a.b.c.d} range IPV4_PREFIX substitute IPV4_PREFIX} {} |
| @deffnx {OSPF Command} {no area @var{a.b.c.d} range IPV4_PREFIX substitute IPV4_PREFIX} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {area @var{a.b.c.d} virtual-link @var{a.b.c.d}} {} |
| @deffnx {OSPF Command} {area <0-4294967295> virtual-link @var{a.b.c.d}} {} |
| @deffnx {OSPF Command} {no area @var{a.b.c.d} virtual-link @var{a.b.c.d}} {} |
| @deffnx {OSPF Command} {no area <0-4294967295> virtual-link @var{a.b.c.d}} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {area @var{a.b.c.d} shortcut} {} |
| @deffnx {OSPF Command} {area <0-4294967295> shortcut} {} |
| @deffnx {OSPF Command} {no area @var{a.b.c.d} shortcut} {} |
| @deffnx {OSPF Command} {no area <0-4294967295> shortcut} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {area @var{a.b.c.d} stub} {} |
| @deffnx {OSPF Command} {area <0-4294967295> stub} {} |
| @deffnx {OSPF Command} {no area @var{a.b.c.d} stub} {} |
| @deffnx {OSPF Command} {no area <0-4294967295> stub} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {area @var{a.b.c.d} stub no-summary} {} |
| @deffnx {OSPF Command} {area <0-4294967295> stub no-summary} {} |
| @deffnx {OSPF Command} {no area @var{a.b.c.d} stub no-summary} {} |
| @deffnx {OSPF Command} {no area <0-4294967295> stub no-summary} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {area @var{a.b.c.d} default-cost <0-16777215>} {} |
| @deffnx {OSPF Command} {no area @var{a.b.c.d} default-cost <0-16777215>} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {area @var{a.b.c.d} export-list NAME} {} |
| @deffnx {OSPF Command} {area <0-4294967295> export-list NAME} {} |
| @deffnx {OSPF Command} {no area @var{a.b.c.d} export-list NAME} {} |
| @deffnx {OSPF Command} {no area <0-4294967295> export-list NAME} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {area @var{a.b.c.d} import-list NAME} {} |
| @deffnx {OSPF Command} {area <0-4294967295> import-list NAME} {} |
| @deffnx {OSPF Command} {no area @var{a.b.c.d} import-list NAME} {} |
| @deffnx {OSPF Command} {no area <0-4294967295> import-list NAME} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {area @var{a.b.c.d} authentication} {} |
| @deffnx {OSPF Command} {area <0-4294967295> authentication} {} |
| @deffnx {OSPF Command} {no area @var{a.b.c.d} authentication} {} |
| @deffnx {OSPF Command} {no area <0-4294967295> authentication} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {area @var{a.b.c.d} authentication message-digest} {} |
| @deffnx {OSPF Command} {area <0-4294967295> authentication message-digest} {} |
| @end deffn |
| |
| @node OSPF interface, Redistribute routes to OSPF, OSPF area, OSPFv2 |
| @comment node-name, next, previous, up |
| @section OSPF interface |
| |
| @deffn {Interface Command} {ip ospf authentication-key AUTH_KEY} {} |
| @deffnx {Interface Command} {no ip ospf authentication-key} {} |
| Set OSPF authentication key to a simple password. After setting @var{AUTH_KEY}, |
| all OSPF packets are authenticated. @var{AUTH_KEY} has length up to 8 chars. |
| @end deffn |
| |
| @deffn {Interface Command} {ip ospf message-digest-key KEYID md5 KEY} {} |
| @deffnx {Interface Command} {no ip ospf message-digest-key} {} |
| Set OSPF authentication key to a cryptographic password. The cryptographic |
| algorithm is MD5. KEYID identifies secret key used to create the message |
| digest. KEY is the actual message digest key up to 16 chars. |
| @end deffn |
| |
| @deffn {Interface Command} {ip ospf cost <1-65535>} {} |
| @deffnx {Interface Command} {no ip ospf cost} {} |
| Set link cost for the specified interface. The cost value is set to router-LSA's |
| metric field and used for SPF calculation. |
| @end deffn |
| |
| @deffn {Interface Command} {ip ospf dead-interval <1-65535>} {} |
| @deffnx {Interface Command} {no ip ospf dead-interval} {} |
| Set number of seconds for RouterDeadInterval timer value used for Wait Timer |
| and Inactivity Timer. This value must be the same for all routers attached |
| to a common network. The default value is 40 seconds. |
| @end deffn |
| |
| @deffn {Interface Command} {ip ospf hello-interval <1-65535>} {} |
| @deffnx {Interface Command} {no ip ospf hello-interval} {} |
| Set number of seconds for HelloInterval timer value. Setting this value, |
| Hello packet will be sent every timer value seconds on the specified interface. |
| This value must be the same for all routers attached to a common network. |
| The default value is 10 seconds. |
| @end deffn |
| |
| @deffn {Interface Command} {ip ospf network (broadcast|non-broadcast|point-to-multipoint|point-to-point)} {} |
| @deffnx {Interface Command} {no ip ospf network} {} |
| Set explicitly network type for specifed interface. |
| @end deffn |
| |
| @deffn {Interface Command} {ip ospf priority <0-255>} {} |
| @deffnx {Interface Command} {no ip ospf priority} {} |
| Set RouterPriority integer value. Setting higher value, router will be more |
| eligible to become Designated Router. Setting the value to 0, router is no |
| longer eligible to Designated Router. |
| The default value is 1. |
| @end deffn |
| |
| @deffn {Interface Command} {ip ospf retransmit-interval <1-65535>} {} |
| @deffnx {Interface Command} {no ip ospf retransmit interval} {} |
| Set number of seconds for RxmtInterval timer value. This value is used |
| when retransmitting Database Description and Link State Request packets. |
| The default value is 5 seconds. |
| @end deffn |
| |
| @deffn {Interface Command} {ip ospf transmit-delay} {} |
| @deffnx {Interface Command} {no ip ospf transmit-delay} {} |
| Set number of seconds for InfTransDelay value. LSAs' age should be |
| incremented by this value when transmitting. |
| The default value is 1 seconds. |
| @end deffn |
| |
| @node Redistribute routes to OSPF, Showing OSPF information, OSPF interface, OSPFv2 |
| @comment node-name, next, previous, up |
| @section Redistribute routes to OSPF |
| |
| @deffn {OSPF Command} {redistribute (kernel|connected|static|rip|bgp)} {} |
| @deffnx {OSPF Command} {redistribute (kernel|connected|static|rip|bgp) @var{route-map}} {} |
| @deffnx {OSPF Command} {redistribute (kernel|connected|static|rip|bgp) metric-type (1|2)} {} |
| @deffnx {OSPF Command} {redistribute (kernel|connected|static|rip|bgp) metric-type (1|2) route-map @var{word}} {} |
| @deffnx {OSPF Command} {redistribute (kernel|connected|static|rip|bgp) metric <0-16777214>} {} |
| @deffnx {OSPF Command} {redistribute (kernel|connected|static|rip|bgp) metric <0-16777214> route-map @var{word}} {} |
| @deffnx {OSPF Command} {redistribute (kernel|connected|static|rip|bgp) metric-type (1|2) metric <0-16777214>} {} |
| @deffnx {OSPF Command} {redistribute (kernel|connected|static|rip|bgp) metric-type (1|2) metric <0-16777214> route-map @var{word}} {} |
| @deffnx {OSPF Command} {no redistribute (kernel|connected|static|rip|bgp)} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {default-information originate} {} |
| @deffnx {OSPF Command} {default-information originate metric <0-16777214>} {} |
| @deffnx {OSPF Command} {default-information originate metric <0-16777214> metric-type (1|2)} {} |
| @deffnx {OSPF Command} {default-information originate metric <0-16777214> metric-type (1|2) route-map @var{word}} {} |
| @deffnx {OSPF Command} {default-information originate always} {} |
| @deffnx {OSPF Command} {default-information originate always metric <0-16777214>} {} |
| @deffnx {OSPF Command} {default-information originate always metric <0-16777214> metric-type (1|2)} {} |
| @deffnx {OSPF Command} {default-information originate always metric <0-16777214> metric-type (1|2) route-map @var{word}} {} |
| @deffnx {OSPF Command} {no default-information originate} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {distribute-list NAME out (kernel|connected|static|rip|ospf} {} |
| @deffnx {OSPF Command} {no distribute-list NAME out (kernel|connected|static|rip|ospf} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {default-metric <0-16777214>} {} |
| @deffnx {OSPF Command} {no default-metric} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {distance <1-255>} {} |
| @deffnx {OSPF Command} {no distance <1-255>} {} |
| @end deffn |
| |
| @deffn {OSPF Command} {distance ospf (intra-area|inter-area|external) <1-255>} {} |
| @deffnx {OSPF Command} {no distance ospf} {} |
| @end deffn |
| |
| @deffn {Command} {router zebra} {} |
| @deffnx {Command} {no router zebra} {} |
| @end deffn |
| |
| @node Showing OSPF information, Debugging OSPF, Redistribute routes to OSPF, OSPFv2 |
| @comment node-name, next, previous, up |
| @section Showing OSPF information |
| |
| @deffn {Command} {show ip ospf} {} |
| @end deffn |
| |
| @deffn {Command} {show ip ospf interface [INTERFACE]} {} |
| @end deffn |
| |
| @deffn {Command} {show ip ospf neighbor} {} |
| @deffnx {Command} {show ip ospf neighbor INTERFACE} {} |
| @deffnx {Command} {show ip ospf neighbor detail} {} |
| @deffnx {Command} {show ip ospf neighbor INTERFACE detail} {} |
| @end deffn |
| |
| @deffn {Command} {show ip ospf database} {} |
| @end deffn |
| |
| @deffn {Command} {show ip ospf database (asbr-summary|external|network|router|summary)} {} |
| @deffnx {Command} {show ip ospf database (asbr-summary|external|network|router|summary) @var{link-state-id}} {} |
| @deffnx {Command} {show ip ospf database (asbr-summary|external|network|router|summary) @var{link-state-id} adv-router @var{adv-router}} {} |
| @deffnx {Command} {show ip ospf database (asbr-summary|external|network|router|summary) adv-router @var{adv-router}} {} |
| @deffnx {Command} {show ip ospf database (asbr-summary|external|network|router|summary) @var{link-state-id} self-originate} {} |
| @deffnx {Command} {show ip ospf database (asbr-summary|external|network|router|summary) self-originate} {} |
| @end deffn |
| |
| @deffn {Command} {show ip ospf database max-age} {} |
| @end deffn |
| |
| @deffn {Command} {show ip ospf database self-originate} {} |
| @end deffn |
| |
| @deffn {Command} {show ip ospf refresher} {} |
| @end deffn |
| |
| @deffn {Command} {show ip ospf route} {} |
| @end deffn |
| |
| @node Debugging OSPF, , Showing OSPF information, OSPFv2 |
| @comment node-name, next, previous, up |
| @section Debugging OSPF |
| |
| @deffn {Command} {debug ospf packet (hello|dd|ls-request|ls-update|ls-ack|all) (send|recv) [detail]} {} |
| @deffnx {Command} {no debug ospf packet (hello|dd|ls-request|ls-update|ls-ack|all) (send|recv) [detail]} {} |
| @end deffn |
| |
| @deffn {Command} {debug ospf ism} {} |
| @deffnx {Command} {debug ospf ism (status|events|timers)} {} |
| @deffnx {Command} {no debug ospf ism} {} |
| @deffnx {Command} {no debug ospf ism (status|events|timers)} {} |
| @end deffn |
| |
| @deffn {Command} {debug ospf nsm} {} |
| @deffnx {Command} {debug ospf nsm (status|events|timers)} {} |
| @deffnx {Command} {no debug ospf nsm} {} |
| @deffnx {Command} {no debug ospf nsm (status|events|timers)} {} |
| @end deffn |
| |
| @deffn {Command} {debug ospf lsa} {} |
| @deffnx {Command} {debug ospf lsa (generate|flooding|refresh)} {} |
| @deffnx {Command} {no debug ospf lsa} {} |
| @deffnx {Command} {no debug ospf lsa (generate|flooding|refresh)} {} |
| @end deffn |
| |
| @deffn {Command} {debug ospf zebra} {} |
| @deffnx {Command} {debug ospf zebra (interface|redistribute)} {} |
| @deffnx {Command} {no debug ospf zebra} {} |
| @deffnx {Command} {no debug ospf zebra (interface|redistribute)} {} |
| @end deffn |
| |
| @deffn {Command} {show debugging ospf} {} |
| @end deffn |
| |