vendor/github.com/opencord/omci-lib-go/generated/dot1agmaintenancedomain.go

/*
 * Copyright (c) 2018 - present.  Boling Consulting Solutions (bcsw.net)
 * Copyright 2020-present Open Networking Foundation

 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at

 * http://www.apache.org/licenses/LICENSE-2.0

 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */
/*
 * NOTE: This file was generated, manual edits will be overwritten!
 *
 * Generated by 'goCodeGenerator.py':
 *              https://github.com/cboling/OMCI-parser/README.md
 */

package generated

import "github.com/deckarep/golang-set"

// Dot1AgMaintenanceDomainClassID is the 16-bit ID for the OMCI
// Managed entity Dot1ag maintenance domain
const Dot1AgMaintenanceDomainClassID ClassID = ClassID(299)

var dot1agmaintenancedomainBME *ManagedEntityDefinition

// Dot1AgMaintenanceDomain (class ID #299)
//	In [IEEE 802.1ag], a maintenance domain (MD) is a context within which configuration fault
//	management (CFM) connectivity verification can occur. Individual services (maintenance
//	associations, MAs) exist within an MD. An MD is created and deleted by the OLT. The MD ME is
//	specified by [IEEE 802.1ag] in such a way that the same provisioning can be used for all
//	associated systems in a network; the OMCI definition accordingly avoids ONU-specific information
//	such as pointers.
//
//	Relationships
//		Several MDs may be associated with a given bridge, at various MD levels, and a given MD may be
//		associated with any number of bridges.
//
//	Attributes
//		Managed Entity Id
//			This attribute uniquely identifies an instance of this ME. The values 0 and 0xFFFF are reserved.
//			(R, setbycreate) (mandatory) (2-bytes)
//
//		Md Level
//			This attribute ranges from 0..7 and specifies the maintenance level of this MD. Higher numbers
//			have wider geographic scope. (R,-W, setbycreate) (mandatory) (1-byte)
//
//		Md Name Format
//			This attribute specifies one of several possible formats for the MD name attribute. (R,-W,
//			setbycreate) (mandatory) (1-byte)
//
//		MD Name 1
//			These two attributes may be regarded as a 50-byte octet string whose value is the left-justified
//			maintenance domain name. The MD name may or may not be a printable character string, so an octet
//			string is the appropriate representation. If the MD name format specifies a DNS-like name or a
//			character string, the string is null-terminated; otherwise, its length is determined by the MD
//			name format. If the MD has no name (MD name format-=-0), this attribute is undefined. Note that
//			binary comparisons of the MD name are made in other CFM state machines, so blanks, alphabetic
//			case, etc., are significant. Also, note that the MD name and the MA name must be packed (with
//			additional bytes) into 48-byte CFM message headers. (R,-W) (mandatory if MD name format is not
//			1) (25-bytes * 2 attributes)
//
//		MD Name 2
//			These two attributes may be regarded as a 50-byte octet string whose value is the left-justified
//			maintenance domain name. The MD name may or may not be a printable character string, so an octet
//			string is the appropriate representation. If the MD name format specifies a DNS-like name or a
//			character string, the string is null-terminated; otherwise, its length is determined by the MD
//			name format. If the MD has no name (MD name format-=-0), this attribute is undefined. Note that
//			binary comparisons of the MD name are made in other CFM state machines, so blanks, alphabetic
//			case, etc., are significant. Also, note that the MD name and the MA name must be packed (with
//			additional bytes) into 48-byte CFM message headers. (R,-W) (mandatory if MD name format is not
//			1) (25-bytes * 2 attributes)
//
//		Maintenance Domain Intermediate Point Half Function Mhf Creation
//			Maintenance domain intermediate point half function (MHF) creation: This attribute determines
//			whether an associated bridge creates an MHF for this MD, under circumstances defined in
//			clause-22.2.3 of [IEEE 802.1ag]. This attribute is an enumeration with the following values.
//
//			1	None
//
//			2	Default (IEEE 802.1ag term). The bridge can create MHFs on an associated VID on any port
//			through which the VID can pass, where: i) there are no lower active MD levels or ii) there is a
//			maintenance association end point (MEP) at the next lower active MD level on the port.
//
//			3	Explicit. The bridge can create MHFs on an associated VID on any port through which the VID
//			can pass, but only if an MEP exists at some lower maintenance level.
//
//			(R,-W, setbycreate) (mandatory) (1-byte)
//
//		Sender Id Permission
//			This attribute determines the contents of the sender ID type-length-value (TLV) included in CFM
//			messages transmitted by maintenance points (MPs) controlled by this MD. Chassis ID and
//			management address information is available from the dot1ag chassismanagement info ME. The
//			attribute is an enumeration with the following values.
//
//			1	None: the sender ID TLV is not to be sent.
//
//			2	Chassis: the chassis ID length, chassis ID subtype, and chassis ID fields of the sender ID TLV
//			are to be sent, but not the management address fields.
//
//			3	Manage: the management address fields of the sender ID TLV are to be sent, but the chassis ID
//			length is to be transmitted with the value 0, and the chassis ID subtype, and chassis ID fields
//			are not to be sent.
//
//			4	ChassisManage: all chassis ID and management address fields are to be sent.
//
//			(R,-W, setbycreate) (mandatory) (1-byte)
//
type Dot1AgMaintenanceDomain struct {
	ManagedEntityDefinition
	Attributes AttributeValueMap
}

func init() {
	dot1agmaintenancedomainBME = &ManagedEntityDefinition{
		Name:    "Dot1AgMaintenanceDomain",
		ClassID: 299,
		MessageTypes: mapset.NewSetWith(
			Create,
			Delete,
			Get,
			Set,
		),
		AllowedAttributeMask: 0xfc00,
		AttributeDefinitions: AttributeDefinitionMap{
			0: Uint16Field("ManagedEntityId", PointerAttributeType, 0x0000, 0, mapset.NewSetWith(Read, SetByCreate), false, false, false, 0),
			1: ByteField("MdLevel", UnsignedIntegerAttributeType, 0x8000, 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, 1),
			2: ByteField("MdNameFormat", UnsignedIntegerAttributeType, 0x4000, 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, 2),
			3: MultiByteField("MdName1", OctetsAttributeType, 0x2000, 25, toOctets("AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA=="), mapset.NewSetWith(Read, Write), false, false, false, 3),
			4: MultiByteField("MdName2", OctetsAttributeType, 0x1000, 25, toOctets("AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA=="), mapset.NewSetWith(Read, Write), false, false, false, 4),
			5: ByteField("MaintenanceDomainIntermediatePointHalfFunctionMhfCreation", UnsignedIntegerAttributeType, 0x0800, 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, 5),
			6: ByteField("SenderIdPermission", UnsignedIntegerAttributeType, 0x0400, 0, mapset.NewSetWith(Read, SetByCreate, Write), false, false, false, 6),
		},
		Access:  CreatedByOlt,
		Support: UnknownSupport,
	}
}

// NewDot1AgMaintenanceDomain (class ID 299) creates the basic
// Managed Entity definition that is used to validate an ME of this type that
// is received from or transmitted to the OMCC.
func NewDot1AgMaintenanceDomain(params ...ParamData) (*ManagedEntity, OmciErrors) {
	return NewManagedEntity(*dot1agmaintenancedomainBME, params...)
}