| # Copyright 2020 - present Open Networking Foundation |
| # |
| # Licensed under the Apache License, Version 2.0 (the "License"); |
| # you may not use this file except in compliance with the License. |
| # You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, software |
| # distributed under the License is distributed on an "AS IS" BASIS, |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| # See the License for the specific language governing permissions and |
| # limitations under the License. |
| |
| *** Settings *** |
| Documentation Test various failure scenarios |
| Suite Setup Setup Suite |
| Test Setup Setup |
| Test Teardown Teardown |
| #Suite Teardown Teardown Suite |
| Library Collections |
| Library String |
| Library OperatingSystem |
| Library XML |
| Library RequestsLibrary |
| Library ../../libraries/DependencyLibrary.py |
| Resource ../../libraries/onos.robot |
| Resource ../../libraries/voltctl.robot |
| Resource ../../libraries/voltha.robot |
| Resource ../../libraries/utils.robot |
| Resource ../../libraries/k8s.robot |
| Resource ../../variables/variables.robot |
| Resource ../../libraries/power_switch.robot |
| |
| *** Variables *** |
| ${POD_NAME} flex-ocp-cord |
| ${KUBERNETES_CONF} ${KUBERNETES_CONFIGS_DIR}/${POD_NAME}.conf |
| ${KUBERNETES_CONFIGS_DIR} ~/pod-configs/kubernetes-configs |
| #${KUBERNETES_CONFIGS_DIR} ${KUBERNETES_CONFIGS_DIR}/${POD_NAME}.conf |
| ${KUBERNETES_YAML} ${KUBERNETES_CONFIGS_DIR}/${POD_NAME}.yml |
| ${HELM_CHARTS_DIR} ~/helm-charts |
| ${VOLTHA_POD_NUM} 8 |
| ${NAMESPACE} voltha |
| ${DEFAULTSPACE} default |
| # For below variable value, using deployment name as using grep for |
| # parsing radius pod name, we can also use full radius pod name |
| ${RESTART_POD_NAME} radius |
| ${timeout} 60s |
| ${of_id} 0 |
| ${logical_id} 0 |
| ${has_dataplane} True |
| ${teardown_device} False |
| ${scripts} ../../scripts |
| |
| # Per-test logging on failure is turned off by default; set this variable to enable |
| ${container_log_dir} ${None} |
| |
| *** Test Cases *** |
| Verify OLT after rebooting physically - MultipleOLT |
| [Documentation] Test the physical reboot of the OLT |
| ... Prerequisite : Subscriber are authenticated/DHCP/pingable state |
| ... Test performs a physical reboot on one of the OLTs, performs "reboot" from the OLT CLI |
| ... Validates that ONU on other OLTs are still functional |
| [Tags] functional MultiOlt-PhysicalOLTReboot |
| [Setup] Start Logging MultipleOlt-PhysicalOLTReboot |
| [Teardown] Run Keywords Collect Logs |
| ... AND Stop Logging MultipleOlt-PhysicalOLTReboot |
| Delete All Devices and Verify |
| # Add OLT device |
| setup |
| # Performing Sanity Test to make sure subscribers are all AUTH+DHCP and pingable |
| Run Keyword If ${has_dataplane} Clean Up Linux |
| Wait Until Keyword Succeeds ${timeout} 2s Perform Sanity Test |
| # Execute the test when the number of OLTs are greater than one |
| Pass Execution If ${olt_count} == 1 Skipping test: just one OLT |
| # Reboot the first OLT from the list of olts - rebooting from the OLT CLI |
| ${olt_user}= Get From Dictionary ${list_olts}[0] user |
| ${olt_pass}= Get From Dictionary ${list_olts}[0] pass |
| ${olt_ssh_ip}= Get From Dictionary ${list_olts}[0] sship |
| ${olt_serial_number}= Get From Dictionary ${list_olts}[0] sn |
| ${olt_device_id}= Get OLTDeviceID From OLT List ${olt_serial_number} |
| Run Keyword If ${has_dataplane} Login And Run Command On Remote System |
| ... sudo reboot ${olt_ssh_ip} ${olt_user} ${olt_pass} prompt=# |
| # validate that the ONUs on the other OLTs are still functional |
| Verify ping is successful for ONUs not on this OLT ${num_all_onus} ${olt_device_id} |
| Run Keyword And Ignore Error Collect Logs |
| # Validate that the ONUs on the rebooted OLT are not pingable |
| FOR ${I} IN RANGE 0 ${num_all_onus} |
| ${src}= Set Variable ${hosts.src[${I}]} |
| ${dst}= Set Variable ${hosts.dst[${I}]} |
| ${olt_serial_number}= Get From Dictionary ${list_olts}[0] sn |
| Continue For Loop If "${olt_serial_number}"!="${src['olt']}" |
| Run Keyword If ${has_dataplane} Run Keyword And Continue On Failure |
| ... Wait Until Keyword Succeeds 60s 2s |
| ... Check Ping False ${dst['dp_iface_ip_qinq']} ${src['dp_iface_name']} |
| ... ${src['ip']} ${src['user']} ${src['pass']} ${src['container_type']} ${src['container_name']} |
| END |
| # Wait for the rebooted OLT to come back up |
| ${olt_serial_number}= Get From Dictionary ${olt_ids}[0] sn |
| ${olt_user}= Get From Dictionary ${list_olts}[0] user |
| ${olt_pass}= Get From Dictionary ${list_olts}[0] pass |
| ${olt_ssh_ip}= Get From Dictionary ${list_olts}[0] sship |
| ${olt_device_id}= Get OLTDeviceID From OLT List ${olt_serial_number} |
| Run Keyword If ${has_dataplane} Wait Until Keyword Succeeds 120s 10s |
| ... Check Remote System Reachability True ${olt_ssh_ip} |
| Run Keyword And Continue On Failure Wait Until Keyword Succeeds 360s 5s |
| ... Validate OLT Device ENABLED ACTIVE |
| ... REACHABLE ${olt_serial_number} |
| # Waiting extra time for the ONUs to come up |
| Sleep 60s |
| Run Keyword And Ignore Error Collect Logs |
| Run Keyword If ${has_dataplane} Clean Up Linux |
| Wait Until Keyword Succeeds ${timeout} 2s Perform Sanity Test |
| # Deleting OLT after test completes |
| #Run Keyword If ${has_dataplane} Delete All Devices and Verify |
| END |
| |
| Verify OLT Soft Reboot - MultipleOLT |
| [Documentation] Test soft reboot of the OLT using voltctl command |
| ... Verifies that when one OLT is rebooted other ONUs on other OLTs are |
| ... still functional |
| [Tags] MultiOlt-OLTSoftReboot functional |
| [Setup] Start Logging MultiOlt-OLTSoftReboot |
| [Teardown] Run Keywords Collect Logs |
| ... AND Stop Logging MultiOlt-OLTSoftReboot |
| ... AND Delete All Devices and Verify |
| #Delete All Devices and Verify |
| #Setup |
| ## Performing Sanity Test to make sure subscribers are all AUTH+DHCP and pingable |
| #Run Keyword If ${has_dataplane} Clean Up Linux |
| #Wait Until Keyword Succeeds ${timeout} 2s Perform Sanity Test |
| # Execute the test when the number of OLTs are greater than one |
| Pass Execution If ${olt_count} == 1 Skipping test: just one OLT |
| # Reboot the first OLT |
| ${olt_user}= Get From Dictionary ${list_olts}[0] user |
| ${olt_pass}= Get From Dictionary ${list_olts}[0] pass |
| ${olt_ssh_ip}= Get From Dictionary ${list_olts}[0] sship |
| ${olt_serial_number}= Get From Dictionary ${list_olts}[0] sn |
| ${olt_device_id}= Get OLTDeviceID From OLT List ${olt_serial_number} |
| Run Keyword And Continue On Failure Wait Until Keyword Succeeds 360s 5s |
| ... Validate OLT Device ENABLED ACTIVE |
| ... REACHABLE ${olt_serial_number} |
| # Reboot the OLT using "voltctl device reboot" command |
| Reboot Device ${olt_device_id} |
| Run Keyword And Ignore Error Collect Logs |
| # validate that the ONUs on the other OLTs are still functional |
| Verify ping is successful for ONUs not on this OLT ${num_all_onus} ${olt_device_id} |
| #Verify that ping fails for the ONUs where the OLT has been rebooted |
| FOR ${I} IN RANGE 0 ${num_all_onus} |
| ${src}= Set Variable ${hosts.src[${I}]} |
| ${dst}= Set Variable ${hosts.dst[${I}]} |
| ${olt_serial_number}= Get From Dictionary ${list_olts}[0] sn |
| Continue For Loop If "${olt_serial_number}"!="${src['olt']}" |
| Run Keyword If ${has_dataplane} Run Keyword And Continue On Failure |
| ... Wait Until Keyword Succeeds 60s 2s |
| ... Check Ping False ${dst['dp_iface_ip_qinq']} ${src['dp_iface_name']} |
| ... ${src['ip']} ${src['user']} ${src['pass']} ${src['container_type']} ${src['container_name']} |
| END |
| # Check OLT state of the rebooted OLT |
| ${olt_serial_number}= Get From Dictionary ${list_olts}[0] sn |
| ${olt_ssh_ip}= Get From Dictionary ${list_olts}[0] sship |
| ${olt_device_id}= Get OLTDeviceID From OLT List ${olt_serial_number} |
| # Wait for the OLT to come back up |
| Run Keyword If ${has_dataplane} Wait Until Keyword Succeeds 120s 10s |
| ... Check Remote System Reachability True ${olt_ssh_ip} |
| # Check OLT states |
| Run Keyword And Continue On Failure Wait Until Keyword Succeeds 360s 5s |
| ... Validate OLT Device ENABLED ACTIVE |
| ... REACHABLE ${olt_serial_number} |
| # Waiting extra time for the ONUs to come up |
| Sleep 60s |
| Run Keyword And Ignore Error Collect Logs |
| #Check after reboot that ONUs are active, authenticated/DHCP/pingable |
| Run Keyword If ${has_dataplane} Clean Up Linux |
| Wait Until Keyword Succeeds ${timeout} 2s Perform Sanity Test |
| |
| |
| *** Keywords *** |
| Setup Suite |
| [Documentation] Set up the test suite |
| Common Test Suite Setup |
| #power_switch.robot needs it to support different vendor's power switch |
| ${switch_type}= Get Variable Value ${web_power_switch.type} |
| Run Keyword If "${switch_type}"!="" Set Global Variable ${powerswitch_type} ${switch_type} |
| |
| Clear All Devices Then Create New Device |
| [Documentation] Remove any devices from VOLTHA and ONOS |
| # Remove all devices from voltha and nos |
| Delete All Devices and Verify |
| # Execute normal test Setup Keyword |
| Setup |