| # SPDX-FileCopyrightText: 2022 Open Networking Foundation <support@opennetworking.org> |
| # |
| # SPDX-License-Identifier: BSD-3-Clause |
| |
| basic: |
| cell_id: 100 |
| mme_address: 172.21.143.206 |
| mme_port: 36412 |
| plmn_list: "305010" |
| pci_list: "100,101" |
| allow_enodeb_transmit: False |
| |
| carrier_number: 2 |
| carrier_agg_enable: False |
| |
| # Automation Configuration Server |
| acs: |
| # To enable/disable to connect the management server (ACS) |
| cwmp_enable: True |
| # Define to enable/disable a periodic inform |
| periodic_inform_enable: True |
| # Interval of a preiodic inform send to ACS |
| periodic_inform_interval: 180 |
| |
| cell: |
| # If True, 64QAM is allowed [TS 36.331] |
| enable64qam: True |
| # Physical Cell ID for cell 1 and cell 2 |
| pci1: 100 |
| pci2: 101 |
| # Tracking Area Code for cell 1 and cell 2 |
| tac1: 501 |
| tac2: 502 |
| # Downlink/Uplink bandwidth |
| downlink_bandwidth: 25 |
| uplink_bandwidth: 25 |
| # EARFCN for 1st frequency band |
| earfcn_downlink1: 55440 |
| earfcn_uplink1: 55440 |
| # EARFCN for 2nd frequency band |
| earfcn_downlink2: 55640 |
| earfcn_uplink2: 55640 |
| # EARFCN for 1st + 2nd frequency band |
| earfcn_downlink_list: "55440,55640" |
| earfcn_uplink_list: "55440,55640" |
| # First/Second Frequency Band Indicator |
| frequency_band_1: 48 |
| frequency_band_2: 48 |
| # Frequency Band List |
| frequency_band_list: "48, 48" |
| # The DL/UL subframe configuration |
| subframe_assignment: 2 |
| # The TDD special sub-frame pattern [TS 36.331 sec 6.3.2] |
| special_subframe_pattern: 7 |
| |
| # The real TX power |
| tx_power: 20 |
| # Tunnel type |
| tunnel_type: "Device.IP.Interface.1.IPv4Address.1." |
| |
| |
| # Femtocell Access Point Control Parameters |
| fap_control: |
| # The administrative state of LTE FAP |
| # If True, the cell unlock and enable RF to serve traffic |
| admin_state: False |
| # Radio Resource Management |
| is_ca_frequency_contiguous: 0 |
| |
| # Radio Environment Map Parameters |
| rem: |
| primary_source: "FREE_RUNNING" |
| |
| # Spectrum Access System (SAS) |
| sas: |
| # If True, eNodeB will be admistrated by SAS |
| sas_enable: True |
| # If True, it indicates device configuration was signed by CPI key |
| cpi_enable: True |
| # If True, add manufacturer name as prefix of Serial Number |
| manufacturer_prefix_enable: True |
| # The SAS server address |
| sas_server_url: "https://sas.goog/v1.2/" |
| # The username registered to SAS |
| sas_uid: "aether" |
| # Define device's SAS category [CFR 96.39(c)] |
| sas_category: "A" |
| # PAL or GAA |
| sas_channel_type: "GAA" |
| # The device's certification name, it uses to communicate with SAS server |
| sas_cert_subject: "ENODEBD_CONFIGURED_SAS_CERT" |
| # Location: indoor / outdoor |
| sas_location: "indoor" |
| # AGL or AMSL |
| sas_height_type: "AGL" |
| # FCC ID of device |
| sas_fccid: "ENODEBD_CONFIGURED_FCCID" |
| # RECEIVED_POWER_WITH_GRANT / RECEIVED_POWER_WITHOUT_GRANT |
| sas_measure_capability: "RECEIVED_POWER_WITHOUT_GRANT" |
| # Your CPI name |
| sas_cpi_name: "ONF_CPI" |
| # Your CPI Certification ID |
| sas_cpi_id: "GOOG-999999" |
| # Device antenna parameters |
| sas_antenna_azimuth: 0 |
| sas_antenna_downtilt: 0 |
| sas_antenna_gain: 5 |
| sas_antenna_beamwidth: 360 |
| # The signature of configuration |
| sas_cpi_signature_data: "ENODEBD_CONFIGURED_CPI_SIGNED_DATA" |