| paul | 718e374 | 2002-12-13 20:15:29 +0000 | [diff] [blame^] | 1 | |
| 2 | Zebra OSPF daemon for IPv6 network |
| 3 | |
| 4 | 2001/12/20 |
| 5 | |
| 6 | Zebra OSPF6d is OSPF version 3 daemon which is specified by |
| 7 | "OSPF for IPv6" (RFC 2740). |
| 8 | |
| 9 | *** NOTE *** |
| 10 | Zebra ospf6d is in development yet. It may lack some functionalities, |
| 11 | and may have some bugs. Use the latest version from the anoncvs |
| 12 | repository (http://www.zebra.org/cvs.html) ! |
| 13 | |
| 14 | This file README is like memo yet, so please feel free to ask |
| 15 | <yasu@sfc.wide.ad.jp> by E-mail. Patches will be appriciated. |
| 16 | |
| 17 | ospf6d's vty port was default to 2606/tcp. |
| 18 | Use commands below. |
| 19 | |
| 20 | VIEW NODE: |
| 21 | show ipv6 ospf6 |
| 22 | To see Router-ID, uptime of ospf6d, some statistics. |
| 23 | |
| 24 | show ipv6 ospf6 database ... |
| 25 | This command shows LSA database. You can specify |
| 26 | LS-type/LS-ID/Advertising-Router of LSAs. '*' is recognized. |
| 27 | |
| 28 | show ipv6 ospf6 interface ... |
| 29 | To see the status of the OSPF interface, and the configuration |
| 30 | like interface costs. |
| 31 | |
| 32 | show ipv6 ospf6 neighbor ... |
| 33 | Shows state of neighbors and choosed (Backup) DR on the I/F. |
| 34 | |
| 35 | show ipv6 ospf6 route (X::X) |
| 36 | This command shows internal routing table of the ospf6d. |
| 37 | Routes not calculated by OSPFv3 (like connected routes) |
| 38 | are not shown. If Address is specified (X::X), shows the route |
| 39 | that the address matches. |
| 40 | |
| 41 | show ipv6 ospf6 route redistribute (X::X) |
| 42 | Shows the routes advertised as AS-External routes by the router |
| 43 | itself. If Address is specified (X::X), shows the route |
| 44 | that the address matches. |
| 45 | |
| 46 | CONFIG NODE: |
| 47 | interface NAME |
| 48 | To enter INTERFACE NODE |
| 49 | |
| 50 | router ospf6 ... |
| 51 | To enter OSPF6 NODE |
| 52 | |
| 53 | INTERFACE NODE: |
| 54 | ipv6 ospf6 cost COST |
| 55 | Sets the interface's output cost. default 1 |
| 56 | |
| 57 | ipv6 ospf6 hello-interval HELLOINTERVAL |
| 58 | Sets the interface's Hello Interval. default 10 |
| 59 | |
| 60 | ipv6 ospf6 dead-interval DEADINTERVAL |
| 61 | Sets the interface's Router Dead Interval. default 40 |
| 62 | |
| 63 | ipv6 ospf6 retransmit-interval RETRANSMITINTERVAL |
| 64 | Sets the interface's Rxmt Interval. default 5 |
| 65 | |
| 66 | ipv6 ospf6 priority PRIORITY |
| 67 | Sets the interface's Router Priority. default 1 |
| 68 | |
| 69 | ipv6 ospf6 transmit-delay TRANSMITDELAY |
| 70 | Sets the interface's Inf-Trans-Delay. default 1 |
| 71 | |
| 72 | OSPF6 NODE: |
| 73 | router-id A.B.C.D |
| 74 | Sets the router's Router-ID |
| 75 | |
| 76 | interface NAME area AREA |
| 77 | Binds interface to specified Area, and start |
| 78 | sending OSPFv3 packets. |
| 79 | |
| 80 | Sample configuration is in ospf6d.conf.sample. |
| 81 | |
| 82 | -- |
| 83 | Yasuhiro Ohara <yasu@sfc.wide.ad.jp> |
| 84 | Kunihiro Ishiguro <kunihiro@zebra.org> |
| 85 | |